in the fan
panel. I don’t need the actual size of the holes, just distances to centres.
Thanks in advance.
73,
Alan. G4GNX
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net
're filled with screws and nuts, possibly a plug in the fan
panel. My K3 is in the 2000s, so is far too early for that.
I'll now print your dimensions for my archive and get drilling. :-)
Many thanks again.
73,
Alan. G4GNX
-Original Message-
From: Dave AD6A
Sent: Tuesday, J
Can someone tell me what the difference is between the KX3VA and the KX3VB
modules.
Has an upgrade kit been made available to convert the ‘A’ to the ‘B’ and do I
need it for my K3?
73,
Alan. G4GNX
__
Elecraft mailing list
Home: http
d a UK shipping address, I would be willing to provide it and you
would have to collect from the Brighton (South Coast) area of the UK. Send
me a PM if you need this.
73,
Alan. G4GNX
-Original Message-
From: Martin Sole
Sent: Saturday, February 25, 2017 4:52 AM
To: elecraft@mailman
TYVM. :-)
73,
Alan. G4GNX
-Original Message-
From: Andy McMullin
Sent: Saturday, February 25, 2017 10:36 AM
To: Alan. G4GNX
Cc: elecraft@mailman.qth.net
Subject: Re: [Elecraft] K2 kit ordering
An excellent summary Alan
?
I realise that I would need a cable with all pins connected, then snip out the
pins that should not be connected. I would happily buy another KPAK3AUX cable
from Elecraft, but for an item which is readily available in the UK, it’s not
really economical.
73,
Alan. G4GNX
them in the UK, also
Mouser, so I’ve ordered a new cable from Digi-Key.
The Elecraft distributors in the UK have the KPAK3AUX kit, but they won’t sell
just the cable on its own, so you end up paying for parts you don’t need.
73,
Alan. G4GNX
From: Bob Wilson, N6TV
Sent: Saturday, March 4
use the (converted) Astatic with my K3, I wonder if this
value seems sensible to maintain the correct bias and prevent max bias current
going over 10mA?
73,
Alan. G4GNX
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman
mic plugged in?
As both microphones are electrets, the only way I can think of getting round it
temporarily is to turn the bias off on the rear panel mic, when using the front
panel mic, which is inconvenient and not a ‘clean’ solution.
73,
Alan. G4GNX
Absolutely sure, Bill.
This happened once before with our club's K3 and it was definitely the
issue.
Today on my own K3, I was in QSO and I simply muffled the rear panel
microphone with my hand and the issue went away. The monitor was set at
zero.
73,
Alan. G4GNX
-Original Me
I will do that Bill. I'm sure it's was never intended to work that way. I
can't think of any reason it should, so it's either a bug or something I'm
doing wrong.
73,
Alan. G4GNX
-Original Message-
From: Nr4c
Sent: Wednesday, March 15, 2017 7:47 PM
To:
results, with some being
seemingly unrelated.
73,
Alan. G4GNX
-Original Message-
From: Fred Jensen
Sent: Thursday, March 16, 2017 7:58 PM
To: elecraft@mailman.qth.net
Subject: [Elecraft] K3 - Intermittent FP switches
Related question: My K3 [S/N 642] which I built from the kit has
Also, same facilities as KPA500 and built in KAT1500 tuner.
73,
Alan. G4GNX
-Original Message-
From: Gerald Manthey
Sent: Friday, March 17, 2017 5:24 PM
To: Eric Swartz - WA6HHQ, Elecraft
Cc: elecraft@mailman.qth.net
Subject: Re: [Elecraft] Linear thoughts
Super quiet fans! Full
n the device, Windows should recognise it and link it to the
driver.
Why go to Radio Shack for a cable. Surely it's better to give Elecraft the
business by ordering one direct from them?
73,
Alan. G4GNX
-Original Message-
From: WP4CW via Elecraft
Sent: Saturday, March 18, 2017 6:58
dministrator", then follow any prompts.
Be aware that Windows 10 has a nasty habit of hiding prompts behind other
things, so it's best to make sure you have no other apps running, that could
cover any prompts.
Plug in your USB cable and you should be good to go.
73,
Alan. G4GNX
-O
Have you tried accessing the Device Manager via Control Panel to check
whether a port is being assigned when the USB cable is connected to the PC
and the K3?
73,
Alan. G4GNX
-Original Message-
From: Richard Lawn
Sent: Saturday, March 18, 2017 7:58 PM
To: WP4CW
Cc: elecraft
present, but I may have the
CONFIG: KAT500Y set, so I wonder if the K3 displays the symbols when it sends
band change information to the KAT500?
73,
Alan. G4GNX
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Have you actually tried the device on another PC? Could be that it's
coincidentally died.
73,
Alan. G4GNX
-Original Message-
From: Richard Lawn
Sent: Sunday, March 19, 2017 2:00 PM
To: Elecraft@mailman.qth.net
Subject: Re: [Elecraft] k3 not Seen By Computer after OS upgrade
T
Jim.
What Mic Gain and Compression settings do you use with the CM500 headset?
A friend said that he uses MIC=40 and CMP=20, but Howard at Elecraft thinks
that's far too high.
I found that I can get the correct ALC response using Mic=11 and CMP=20.
73,
Alan. G4GNX
-Original Me
Thanks Bill.
That tends to suggest that my setting of 11 is not too far off.
73,
Alan. G4GNX
-Original Message-
From: Bill Frantz
Sent: Sunday, March 26, 2017 8:32 PM
To: Alan. G4GNX
Cc: elecraft@mailman.qth.net
Subject: Re: [Elecraft] RF in Microphone
I use MIC = 8 or 9 and
ne.
Does anyone know if it's possible to change the mic gain setting as part of
a macro and possibly compression levels as well?
73,
Alan. G4GNX
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elec
person or animal could get near the area
whilst the power was on, but I was quite surprised to see how many
earthworms had scuttled their way to the surface.
73,
Alan. G4GNX
-Original Message-
From: Phil Hystad
Sent: Sunday, April 2, 2017 6:31 PM
To: Mike Rhodes
Cc: Elecraft Reflector
copied to the other one and even when
I changed one to it's opposite, that got copied to the other one.
I have yet to verify this as I haven't had time to do so, but I'm hoping it
was just a senior moment illusion. :-)
73,
Alan. G4GNX
-Original Message-
From: To
it seems to have gone past the threshold for long-winded (boring) posts per
thread!
73,
Alan. G4GNX
-Original Message-
From: Bill Johnson
Sent: Tuesday, April 4, 2017 2:22 AM
To: Lynn W. Taylor, WB6UUT ; elecraft@mailman.qth.net
Subject: Re: [Elecraft] [OT] Re: reply to digest
the K3 'real' port number (specified in
Edgeport) within LP-Bridge, but to turn LP-Bridge off when I want to update
firmware and just point the K3 Utility to the K3 'real' port number
directly.
Does this seem like a reasonable thing to d
Thanks Don.
Just trying to be ultra careful as I'll be using the same PC and port and
don't want to brick the K3.
73,
Alan. G4GNX
-Original Message-
From: Don Wilhelm
Sent: Wednesday, April 5, 2017 12:13 PM
To: Alan. G4GNX ; elecraft@mailman.qth.net
Subject: Re: [Elecr
Ha. I've not managed it yet Don, but I read of others occasionally in panic.
I realise that there's a firmware force procedure, but as you say, I don't
want the panic or a heart attack. :-)
One thing I always do is to backup all settings after a permanent change.
7
fe experiences and constructive comparisons of the suites that
are available for use with the K3, peripherals and other software, to help
me decide the best way to go.
73,
Alan. G4GNX
__
Elecraft mailing list
Home: http://ma
round inside one, with a fluorescent tube lit up like Darth Vader!
I asked about tuning for low VSWR and they said they didn't bother much.
What comes back simply goes up again for another try. :-)
73,
Alan. G4GNX
-Original Message-
From: David Woolley
Sent: Saturday, April 22,
observe for changes under test.
73,
Alan. G4GNX
-Original Message-
From: Victor Rosenthal 4X6GP
Sent: Thursday, May 4, 2017 3:07 PM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] K3 with subrx - intermittent main RX problem and pwr
out
Well, I had a relay fail on my KAT3 board. I
is to observe ANTI-STATIC precautions. Use a wrist strap specially made for
the job and preferably use an anti-static mat. DO NOT EVER connect yourself
directly to any anti-static ground source - you could DIE!
73,
Alan. G4GNX
-Original Message-
From: Matt Zilmer
Sent: Thursday, Ma
You can order and download the book in pdf format for $20. Why not help save
the planet? :-)
73,
Alan. G4GNX
-Original Message-
From: Irwin Darack
Sent: Saturday, May 6, 2017 4:52 PM
To: elecraft@mailman.qth.net ; ke9uw
Subject: Re: [Elecraft] K3/K3s Macro Book
I am hoping they
th it very well too.
:-)
I don't expect a radio of any sort to show that accuracy and I must admit to
hardly ever checking the K3's time. It would only be important to me if I
had to set alarms by it.
73,
Alan. G4GNX
-Original Message-
From: Rose
Sent: Sunday, August 28, 2
I believe that the IC7100 has the facility, but it's an option.
73,
Alan. G4GNX
-Original Message-
From: Phil Wheeler
Sent: Sunday, August 28, 2016 6:06 PM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] KXBC3 clock drift & On-Board GPS
As a matter of curiosity bec
, then you are portable.
Something also often used is "static mobile". This suffix does not exist and
IMO sounds rather silly.
73,
Alan. G4GNX
-Original Message-
From: rick jones via Elecraft
Sent: Wednesday, September 7, 2016 9:40 PM
To: Elecraft@mailman.qth.net
Subject: [E
I don't know about other countries but in the UK we have (or at least had) a
"MA" suffix, which stands for Maritime Anchored.
73,
Alan. G4GNX
-Original Message-
From: Fred Jensen
Sent: Wednesday, September 7, 2016 10:46 PM
To: elecraft@mailman.qth.net
Subject: Re:
speaker with a
better device. I don’t really want to start campaigning to purchase an external
speaker for the K3 because it’s another ‘lump’ that needs to be carted around
to club meetings and events.
Thoughts?
73,
Alan. G4GNX
s and discuss some other
topic - LOUDLY. The only answer there seems to be headphones. The same goes
for filed days/contests.
Perhaps we should start to wind this thread up now before it outstays its
welcome? :-)
73,
Alan. G4GNX
-Original Message-
From: Don Wilhelm
Sent: Sa
FWIW they should be easy to find in the UK at Namrick - The Nut and Bolt
Shop, in Hove.
http://www.namrick.co.uk/
73,
Alan. G4GNX
-Original Message-
From: Dave B via Elecraft
Sent: Wednesday, January 18, 2017 8:48 AM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] KAT500
)
so it doesn't have to cost a fortune.
Also, by delving inside your rig, you will learn a lot about "how it ticks".
73,
Alan. G4GNX
-Original Message-
From: Don Wilhelm
Sent: Sunday, January 29, 2017 3:09 AM
To: abulling...@comcast.net ; elecraft
Subject: Re: [Elecraft
rises above 60 degrees C, but the fan doesn't cut in. Does anyone know
if this is normal behavior and what temperatures I should expect to see?
I have tested the fan via the Menu function and it works as expected.
73,
Alan. G4GNX
occurs on a different antenna.
73,
Alan. G4GNX
-- Original Message --
From: "Michael Walker"
To: "Elecraft@mailman.qth.net"
Sent: 10/04/2020 22:48:17
Subject: Re: [Elecraft] KPA 500
This is going to cause a big sh*t storm :) and about 900 emails before
Wayne shu
Chris, you cab buy Perspex polish, but I'm not sure where from right
now. Perhaps eBay?
73,
Alan. G4GNX
-- Original Message --
From: "Chris Cox, N0UK"
To: elecraft@mailman.qth.net
Sent: 14/04/2020 18:14:24
Subject: [Elecraft] PX3 acrylic scratch removal
Can anyone r
Me too. Let's see if this one makes it.
73,
Alan. G4GNX
-- Original Message --
From: "Lou Laderman"
To: elecraft@mailman.qth.net
Sent: 16/05/2020 00:45:17
Subject: [Elecraft] Test
Sorry for the bandwidth, having posting is
Thanks for the confirmation.
There's a filter setting for own message delivery. Mine's set to ON. :-)
I also got my own message back, so I don't know why it wasn't working
before.
73,
Alan. G4GNX
-- Original Message --
From: "Hisashi T Fujinaka"
staff of other companies is next to zero. c) Elecraft support
is second to none. Direct support from other companies is often mediocre
to zero. d) I don't know about other company's staff as I never get to
speak to them, but Elecraft are such a nice bunch of people! (Eric can I
have a
A500 temperature rise is somewhat expected, I feel it's a
bit higher over a short period than I would like and may be due to
reflected power.
73,
Alan. G4GNX
-- Original Message --
From: "David Olean"
To: "Peter Dougherty"
Cc: elecraft@mailman.qth.net
been suggested that lack of AC power may be the cause. That should
be a safe thing to check, without opening the KPA500.
Stay safe - send it back to Elecraft. :-)
73,
Alan. G4GNX
-- Original Message --
From: "Tom Berry"
To: elecraft@mailman.qth.net
Sent: 05/06/2020 17:04:41
S
ucts, including a couple of KPA500s,
and the manual clearly indicates screwing the lid down, before powering
up. There's a good reason for that.
My apologies to the OP. I have no wish to offend you.
73,
Alan. G4GNX
-- Original Message --
From: "Jim Brown"
To: elecra
and very little to do with Elecraft. Please remove it.
73,
Alan. G4GNX
-- Original Message --
From: "Christian Friess"
To: elecraft@mailman.qth.net
Sent: 20/06/2020 18:05:44
Subject: Re: [Elecraft] I'm building a personal email list
I wish that too.
It looks l
oticed a small difference when
using it. Once/if I get the MFJ untit to work, I may then buy one of the
more expensive noise eliminators.
73,
Alan. G4GNX
-- Original Message --
From: g...@gmx.net
To: "Elecraft Reflector"
Sent: 29/06/2020 18:18:30
Subject: [Elecraft] Diversit
The setting for the PA module is probably re-set to NOT INSTALLED.
73,
Alan. G4GNX
-- Original Message --
From: "Bill DeVore"
To: elecraft@mailman.qth.net
Sent: 26/07/2020 20:39:51
Subject: [Elecraft] K3S in QRP mode
I recently did a Parameter Initialization on my K3S
Sorry for the bandwidth.
I just sent two reply messages to this list and they have not appeared
and are not in the archive.
Just generating a new message from scratch. Please ignore.
73,
Alan. G4GNX
__
Elecraft mailing list
Home
r questions when they have
answers. I think other Elecraft staff also keep a weather eye on it.
I didn't setup the K4 group to take over from any Elecraft group, it's
just to separate out K4 traffic from any other Elecraft product, in
response to a request from other prospectiv
iss
anything and cope with traffic that doesn't concern me.
Being a member of several groups allows me to compartmentalise my
interest in multiple products from the same source.
Not trying to 'push' an agenda. Just my personal point of view.
73,
Alan. G4GNX
-- Original
Hehehehe.
Fooled you Rich.
I already changed the subject line. :-D
However, I do agree. Many people are lazy and occasionally some forget,
but once the thread drifts off-topic, I really wish they would change
the subject line.
73,
Alan. G4GNX
-- Original Message --
From: "
What's the problem Steve? November is when I created the group. It's at:
https://groups.io/g/Elecraft-K4
Ring any bells? ;-)
73,
Alan. G4GNX
-- Original Message --
From: "stephen shearer"
To: elecraft@mailman.qth.net
Sent: 28/08/2020 16:26:37
Subject: Re: [E
piece of cable and it just failed.
Unfortunately this is not the sort of fault that can be detected in its
development stage by a low power antenna analyser, it needs a fair
amount of power.
This long tale may just give you some clues to your possible issue on
160m although on a different pow
Malwarebytes reports the link to the radio as insecure with a Trojan, so
I can't see it.
73,
Alan. G4GNX
-- Original Message --
From: "John Harper"
To: "Elecraft list"
Sent: 03/09/2020 18:58:37
Subject: [Elecraft] Is the Lab599 TX500 a "rip-off" o
#x27;float'.
I'd be very surprised if Elecraft had connected the negative supply to
chassis ground inside the KX3 either.
73,
Alan. G4GNX
-- Original Message --
From: "Ian Liston-Smith"
To: "elecraft@mailman.qth.net" ; "Mike Morrow"
Sent: 0
e the use of the
reverse polarity diode. The KX3 circuit diagram is not entirely clear.
73,
Alan. G4GNX
-- Original Message --
From: "Andy Durbin"
To: "elecraft@mailman.qth.net"
Sent: 05/09/2020 19:59:14
Subject: [Elecraft] New KX3 reverse voltage smoke
"If
I'd bet quite a lot that it will only be 50% because most contributors
are too lazy to change the header.
73,
Alan. G4GNX
-- Original Message --
From: "David Gilbert"
To: elecraft@mailman.qth.net
Sent: 07/09/2020 00:52:45
Subject: Re: [Elecraft] With the K4 coming
you setup an AH-4
cable between the rig and tuner. Page 15 of the KAT500 shows how to do
this.
73,
Alan. G4GNX
-- Original Message --
From: "Russell Domareck via Elecraft"
To: "elecraft@mailman.qth.net"
Sent: 12/09/2020 22:04:29
Subject: [Elecraft] K1ZTE - KAT5
each time you
transmit, it should detect the band/frequency and switch to the
appropriate memory.
Memory settings are retained after power down.
73,
Alan. G4GNX
-- Original Message --
From: "Ted Edwards W3TB"
To: "KENT TRIMBLE"
Cc: "elecraft@mailman.qth.net&
. It would of course
be possible to make your own.
73,
Alan. G4GNX
-- Original Message --
From: "w4sc"
To: "elecraft@mailman.qth.net"
Sent: 12/09/2020 23:06:37
Subject: Re: [Elecraft] K1ZTE - KAT500
There may be a clue here
https://kg3v.com/2019/03/03/cant-use-t
00 to the tuner, except for
the RF connection. That way you know that the IC-7300 is only outputting
its intended tuning power and will protect itself.
73,
Alan. G4GNX
-- Original Message --
From: "KENT TRIMBLE"
To: "elecraft@mailman.qth.net"
Sent: 13/09/
The KAT500 retains matched memories for each band/frequency per antenna.
So yes, you have 3 solutions per band/frequency. It has quite a lot of
memories. :-D
73,
Alan. G4GNX
-- Original Message --
From: "w4sc"
To: "elecraft@mailman.qth.net"
Sent: 13/09/2020
For goodness sake, please trim your posts!!! ;-(
73,
Alan. G4GNX
-- Original Message --
From: ccolema...@gmail.com
To: elecraft@mailman.qth.net
Sent: 14/09/2020 21:10:47
Subject: Re: [Elecraft] Elecraft Digest, Vol 197, Issue 18
Sent from my iPhone
On Sep 14, 2020, at 11:03 AM
It really would help if folks were not too lazy to change the subject
line to reflect the actual content. Then we could all decide for
ourselves whether to bother to start reading it.
73,
Alan. G4GNX
-- Original Message --
From: "Jim Sheldon"
To: "Charlie T
ISTR you remove the center strengthening bar (plain aluminum) and it
will probably help to remove the side panel. Then it's a matter of
gentle 'wiggling'.
73,
Alan. G4GNX
-- Original Message --
From: "Grant Youngman"
To: "Tom Fitzpatrick"
Cc: &
racteristic which has resulted in a high current node
which has generated the heat.
You may well be right that your balun is not faulty, but you should
check it anyway as well as checking out all the other aspects of the
installation. If you can, replace the feeder. You may be surpris
. :-)
73,
Alan. G4GNX
-- Original Message --
From: "Bill Coleman"
To: "Alan - G4GNX"
Cc: "Elecraft"
Sent: 14/10/2020 13:39:06
Subject: Re: [Elecraft] [K3] Issue with HI CUR on 12m
I was not seeing any SWR shifts on this antenna. A check with an o
itor, but can't be bothered to learn the correct
terminology. :-)
73,
Alan. G4GNX
-- Original Message --
From: "Jim Brown"
To: elecraft@mailman.qth.net
Sent: 14/10/2020 17:57:31
Subject: Re: [Elecraft] [K3] Issue with HI CUR on 12m
On 10/14/2020 6:19 AM, Alan - G4GNX wrot
rstand the terms they are using, otherwise we get into
meaningless arguments and false advice.
RG213 is a commonly used co-axial cable:
https://www.awcwire.com/productspec.aspx?id=rg213-coaxial-cable
73,
Alan. G4GNX
-- Original Message --
From: j...@kk9a.com
To: elecraft@mailman.qt
to
unbalanced transformer".
In the light of that, I apologise. My information regarding a balun is
useless to you. Sorry to have wasted your time.
BTW I also don't understand where the 1KW rating came from.
73,
Alan. G4GNX
-- Original Message --
From: "Bill Co
No sweat Bill. Sh*t happens. :-D
73,
Alan. G4GNX
-- Original Message --
From: "Bill Coleman"
To: "Alan - G4GNX"
Cc: "Elecraft"
Sent: 14/10/2020 18:55:01
Subject: Re: [Elecraft] [K3] Issue with HI CUR on 12m
In this case, it wasn’t RG-213, but RG-303
I changed the insert for an electret, turn on K3 bias and it works fine.
73,
Alan. G4GNX
-- Original Message --
From: "David F. Reed"
To: "Elecraft Reflector"
Sent: 16/10/2020 17:39:30
Subject: [Elecraft] K3 and Astatic mic?
Anybody have any luck getting a old
r. Don't do anything if you're tired. Plenty of space. Plenty of
light. The right tools and a suitable container for parts.
73,
Alan. G4GNX
-- Original Message --
From: "Jim Spikes N4KH"
To: Elecraft@mailman.qth.net
Sent: 20/10/2020 00:59:06
Subject: [Elecraft] KPA500
Then perhaps someone needs to educate Elecraft not to specify use of a
torque wrench, in their assembly instructions. ;-)
73,
Alan. G4GNX
-- Original Message --
From: "Bert"
To: elecraft@mailman.qth.net
Sent: 20/10/2020 05:15:21
Subject: Re: [Elecraft] KPA500 Transformer
ourse is to get back on
to Elecraft and tell them you think the transformer's faulty.
In the meantime, I guess the only thing you can do is either not use it,
or wear headphones and try to ignore it.
73,
Alan. G4GNX
On 2020-10-20 8:11, jimn4kh wrote:
I wasn't my intention to r
Guys. My comment was sarcastic and has a smiley on the end of it.
Elecraft know what they're doing and I would not expect anyone to tell
them they got it wrong!
73,
Alan. G4GNX
-- Original Message --
From: "Nr4c"
To: "Alan - G4GNX"
Cc: "Elecraft Refl
My CM500 certainly has an electret insert and it came with a separate
plug-in battery bias pack.
Unfortunately the ear pads are starting to deteriorate. Have you had to
replace yours? If so, with what? ISTR I read somewhere that new separate
pads are not available.
73,
Alan. G4GNX
Thanks Charlie.
Fortunately the flaking is only around the periphery, not the part that
touches the ear, so I have a little time yet.
I'll do a search for Velour and see what I can find.
73,
Alan. G4GNX
-- Original Message --
From: "Charlie T"
To: elecraft@mailm
May I suggest checking all your PSUs. I had the same issue once and it
turned out to be the PSU running a tuner. I binned the PSU and installed
a tried and tested new one. No more issues.
73,
Alan. G4GNX
-- Original Message --
From: "Victor Rosenthal"
To: "Elecraft R
KPA500 again
for over an hour (on SSB) and have had no issues.
I've not checked the manuals as to whether the original action is a
safety feature or a bug.
73,
Alan. G4GNX
-- Original Message --
From: "Mike Dodd"
To: elecraft@mailman.qth.net
Sent: 14/11/2020 01:59:57
l set up a high energy field that can destroy the
SDRPlay.
73,
Alan. G4GNX
-- Original Message --
From: "Jim McDonald"
To: "Elecraft Reflector (elecraft@mailman.qth.net)"
Sent: 14/11/2020 16:31:42
Subject: [Elecraft] K3S RX OUT
Can an SDR, such as a SDRPlay RSP
Yes they do. :-)
A little expensive for what it is, but it will do the job.
73,
Alan. G4GNX
-- Original Message --
From: "Bill Steffey NY9H"
To: "Alan - G4GNX" ; "Elecraft Reflector
(elecraft@mailman.qth.net)"
Sent: 14/11/2020 16:48:22
Subject: R
This happened to me last week, although it may not have been a
flashover.
Have you power cycled the K3?
Mine would not output any power after the KPA500 faulted, even when I
turned the KPA500 off. No barefoot power, zilch.
I power cycled the K3 and all restored itself.
73,
Alan. G4GNX
Hi Gernot.
I just downloaded it and will 3D print it as soon as I can.
Looks like a good design and a useful feature.
73,
Alan. G4GNX
-- Original Message --
From: g...@gmx.net
To: elecraft@mailman.qth.net
Sent: 22/12/2020 23:07:32
Subject: [Elecraft] K3 Main knob friction adjustment
Hi Gernot.
I'll hold off with the printing for now.
Still very interested to try out a fully working version.
Something I never thought of designing myself. :-)
73,
Alan. G4GNX
-- Original Message --
From: g...@gmx.net
To: elecraft@mailman.qth.net
Sent: 23/12/2020 00:22:17
Su
Oh God, please don't let us degenerate to this on a Ham Radio group.
73,
Alan. G4GNX
-- Original Message --
From: "Wes"
To: elecraft@mailman.qth.net
Sent: 26/12/2020 01:17:29
Subject: Re: [Elecraft] Genius vs. Stupidity
If you were woke, you'd know that the
yet. I'll be using a mini-whip which comes
recommended for the job. Again though, the MFJ has its limitations when
there are multiple noise sources.
From reports I've read, some people find them great and others not so.
Take a look at a couple of YouTube videos, that might help
n and used as necessary,
several times a week. I have had no issues so far. ;-)
BTW any would-be burglars reading this, don't bother - we have a very
good security system, linked to the Police. :-D
73,
Alan. G4GNX
-- Original Message --
From: "Joseph Shuman via Elecraft&
I can't see that working.
When a renter defaults and does a runner, Elecraft would have to layout
a lot in recovery fees and maybe even end up with a pile of junk for
their trouble.
It might work in a very small country or if they had a physical presence
in all states.
73,
Alan.
The deposit is usually to cover minor damage when an item is returned.
It would have to be as high or higher than the cost to buy a new one, or
the renter could be well out of pocket.
Most would-be renters would be unlikely to want to shell out $400+ as a
deposit.
73,
Alan. G4GNX
Check for dry joints on the wiring to all of the antenna connectors.
73,
Alan. G4GNX
-- Original Message --
From: davein...@comcast.net
To: "elecraft@mailman.qth.net"
Sent: 07/04/2021 23:41:44
Subject: [Elecraft] KAT-500 Increasingly Erratic
I Have a KAT500/KPA 500 co
Is there an update to the KPA500 firmware that reflects the K4?
73,
Alan. G4GNX
-- Original Message --
From: "Bob Wilson, N6TV"
To: "James F. Boehner, MD"
Cc: "Elecraft Reflector"
Sent: 30/04/2021 05:38:24
Subject: Re: [Elecraft] K4 interface to KPA-15
AFAICR The KAT500 follows the K3, not the KPA500, as long as the Aux-bus
cable is connected. I can certainly hear the relays click on the KAT500
when I tune the K3 across a frequency threshold point.
73,
Alan. G4GNX
-- Original Message --
From: p...@xs4all.nl
To: "ele
Thanks Wayne.
I'm sure we all appreciate how busy you must be.
It seems like a reasonable compromise and will help to keep K4 only
subjects separated from other Elecraft product discussions.
73,
Alan. G4GNX
-- Original Message --
From: "Wayne Burdick"
To: &quo
Right above your unsubscribe message is an Unsubscribe link to click on.
:-)
Juste au-dessus de votre message de désabonnement se trouve un lien de
désabonnement sur lequel cliquer. :-)
73,
Alan. G4GNX
-- Original Message --
From: "Jack F6AJW"
To: Elecraft@mailman.qt
1 - 100 of 104 matches
Mail list logo