Hi K2-members;
I do have successfully build a K2/100,but now I like to do some experiments
with a analog S-meter device temporary in place of the standard K2 LED device.
Could someone give me some suggestions where I best,could pickup this 2 wire
S-meter signal for my analog indication
Hi Don;
Good morning,still on factory hier (nucleair powerplant near harbor of Antwerp)
I read a lot about,but do not found any documentation around,how to build of
modify this right led bar of th eK2 unit unit into a visible indicator for the
CW tuning aid !
I like to obtain this modificat
Hi other K2 - KAT 100 owners/builders .
Concerning the allignement of the SWR of the KAT 100 unit with use of C31(SWR
setup allign).
I only could obtain a critical minimum voltage value of 42mVDC on my DMM at pin
3 of the U5 chip in this tuner unit.
Does,some other guys have also those res
Hi K2 users;
I do found next K2-software stage ?
The K2 VFO memory does'nt take next two different VFO settings (example of two
different band settings) VFO A = 20M and VFO B = 17M
In this situation when we switch back to the other VFO,this switched VFO also
take the VFO frequency from the VFO
Hi K2 builders;
I just have finished with the build of my K2 CW/SSB base 10W vesion.
Before I will continue with the build-in my KPA100 unit I will do a whole K2
transmitter final allignement.
I already have done a receiver allignement so the band coils should be quit in
the naber for maximum po
Hi K2 builders;
I do have calibrate my S-meter following exactly what is tell in the building
manual.
I do have done this allignement "CW normal mode".
What I see while switching between CW reverse and USB and LSB mode is that the
right led indication does not indicate most right on other modes
Hi K2 members;
I do have assemble RF board part II starting at page 49 of manual
I have done the allignement test (see my previous E-mail around the results)
But I do only have noise from audio amp but do have no any receive sign's on
40M with antenne connected ?
I do ear nothing around 7000.0 M
Hi K2 builders;
In the main build manual of the K2 they refere on page 29 to fill the leaved
blank holes with components referering to the KSB2 unit page 16.
Those are :
- C4 to C8 0.01uF (103)
- Q3 2N3906
- RP3 10K (partnumber 77083103)
- R13 68K 1%
But regarding at KSB2 parts inventory this
top side of the
backlight unit witch I have fragil removed ..
This is not described yet in manual also !!!
If you forget to take a look on it,you could not removed it anymore once the
LCD unit himself is installed !!!
- Original Message -
From: Alan Price
To: Behiels JeanPierre
I K2 users
I am busy to assembel my front panel control board.
I am quit sure about how mounting the backpanel LCD light but I will be sure
before soldering it into the PCB board.
- I presume the "K" indication of the LCD backlight unit must be soldered into
the "+ (plus) indication on the fro
Hi K2 members;
I am building on a K2(100W) rig.
I near future I will take the rig in use on holidays.
I look for some compact power supply suggestions witch I can take easily in my
luggage during holiday for this purpose.
Has somebody any suggestions around, or some more useful information w
Hi K2 builders;
Could someone give my the datasheet or type number of this used encoder in the
K2 kit.
I like to obtain the mechanical dimensions from this part and his shaft ?
Thanks for the replys.
Regards Jean ON4AEF.
__
Elecraft ma
Hi Elecraft members
Is there any K2 builder witch could give me the exact diameter(mm or inches)
value of the standard delivered VFO dial knob of the K2 rig ,I like to now.
Regards Jean ON4AEF.
__
Elecraft mailing list
Home: http:/
Hi K2 members..
Due the years of production of the K2 rig and witch I folow a lot of time
Is there is nobody who had made the attention to change the LCD display readout
into a LED display reading ??
Personally I think the readebillity of a LED display (by eaxmple for the K2 in
geen ) looks even
14 matches
Mail list logo