Mike,
That problem sounds a bit like the Calibration of the Reference
Oscillator is off a bit. See tha manual and use the Zero-Beating method
as instructed.
There is a chance it will help, but no harm if it does not.
If you did not get the paper manual, download it from Elecraft.
73,
Don
Mike,
Do you have the Noise Blanker turned on? That will create some
"strange" sounds in the audio.
73,
Don W3FPR
On 8/17/2021 5:10 PM, Mike Kholodov via Elecraft wrote:
Listening to the K3S audio had become very fatiguing for me as of late. It
sounds like hum or carrier is m
All,
I was reminded that I should have added that CW and SSB are low duty
cycle modes while FT8 and several other data modes are high duty cycle
and will produce more heat.
The 'finger test' I mentioned is suitable for any mode.
73,
Alternate AF Gain Wiring Modification. You can download the
instructions from the Elecraft website.
73,
Don W3FPR
On 8/16/2021 10:27 AM, Mike Seiffert wrote:
Hi Folks,
I have an Elecraft K2/100 (S/N 01136) given to me by father (SK) some years
ago. I am finally finding some time again for ham
continuous duty and use 1/2 the normal full power output, but I suggest
doing the test I referred to as a specific power limit for your
particular K2.
73,
Don W3FPR
On 8/13/2021 3:38 PM, Aaron K5ATG wrote:
What is the recommended highest power level for a QRP Elecraft K2 to
operate on digital modes
Carter,
Contact support for further assistance.
73,
Don W3FPR
On 8/13/2021 6:43 AM, Carter Craigie wrote:
My thanks to the three fine Elecrafters who sent me suggestions to fix
my KXPA100 amplifier. I tried their suggestions, but no joy.
The problem I have?
After months of fine operation in
email off-reflector (direct email
and take {Elecraft} out of the subject line.
The troubleshooting details are not likely of interest to the rest of
the list. You can summarize the results to the list when it is resolved.
73,
Don W3FPR
On 8/12/2021 1:22 PM, jerry wrote:
On 2021-08-08 09:49, D
Carter,
Check/replug and check again the RJ45 plug on the back of the KXPA100.
It must be locked in place. You should hear a light click as it is
fully seated in its socket.
73,
Don W3FPR
On 8/12/2021 12:42 PM, Carter Craigie wrote:
My problems all started when I moved my Elecraft KX3
That won't work - the KPA100 must be physically removed to keep the base
K2 from using the KPA100 wattmeter.
73,
Don W3FPR
On 8/8/2021 1:54 PM, Frank Krozel wrote:
Just power the radio, not the PA
-73- Frank KG9H
kg9hfr...@gmail.com <mailto:kg9hfr...@gmail.com>
On Aug 8,
long as the KPA100 is installed on the
base K2 - reducing the power to less than 12 watts does not take it out
of line.
CAL CUR should be set at 3.5 amperes with the KPA100 installed. That
(and the current display) is the current drawn by only the base K2, and
not to the KPA100.
73,
Don
vertical board near the left rear corner. You
should see the male header easily.
If you have a saved configuration file, load it, and I think your K3
will come back to life.
73,
Don W3FPR
On 8/8/2021 11:30 AM, Richard Isaacs via Elecraft wrote:
As mentioned, one day it worked, overnight
get to the headphone
jack, take a look at https://www.qsl.net/wy3a/Replace_K2_Headphone_Jack.htm.
73,
Don W3FPR
On 8/7/2021 2:05 PM, jerry wrote:
All,
My new K2/100 has a scratchy volume control knob. Also, it still
makes noise
at full CCW. I suspect that the volume control mod was not done
solder remains in
the holes, heat the solder pad and push it out with a wooden toothpick.
73,
Don W3FPR
On 8/7/2021 1:48 AM, RVZ via Elecraft wrote:
Hi Guys,
I received a used K3/10 this week via UPS Ground and it arrived sick. The radio looks "Like New"
even though it's an old
connection to pin 6.
73,
Don W3FPR
On 8/5/2021 10:50 AM, Aaron K5ATG wrote:
I have been using a Signalink USB with my K2 and the last time I
hooked the SignaLink to the K2 there was a real bad feedback sound
every time the rig went into transmit. It received just fine. So I
contacted Tigertronics
Tom and all,
Elecraft still offers service on its legacy gear - KX1, K1, K2,
XVseries, so as long as repair parts are available, you can expect
service will be available for the K3/K3S in a similar manner.
73,
Don W3FPR
On 8/2/2021 9:26 AM, Thomas Donohue wrote:
Given the termination of
CW on the AM broadcast band - but that is just a
guess.
73,
Don W3FPR
On 7/26/2021 2:05 PM, Tom wrote:
Hi
I don't recall this happening before, but if I am tuned to a signal lets say
at 1.000 MHz in AM and then I switch to CW, the frequency display on the
radio changes to 1.600 MHz.
My K
occurs in just the base K2, hold your finger on the relays one by
one and see if you can detect which one is switching as you key the K2.
73,
Don W3FPR
On 7/24/2021 5:22 PM, K9SW wrote:
Recently bought a K2 and all was working well (silent QSK) until I moved from
one spot on the bench to
Doug,
The answer is "yes and no".
Set the sidetone pitch in the menu, then adjust capacitor C20 (BFO
adjust) to center the filter at 600 Hz.
You also need to adjust the Transmit Offset to match (adjust C13) - see
the manual for the procedure.
73,
Don W3FPR
On 7/23/2021 11:58 A
to hazards.
73,
Don W3FPR
On 7/21/2021 10:43 PM, Dave wrote:
Hi,
I am unsure what you are asking... If you are asking about fuse
values, I select values a bit above the max peak current I expect.
For my K3 I use a 30 amp fuse.
If you are asking about voltage drop, and want to know what
We used Vodka for cleaning VHF and UHF broadcast transmitters. Told by RCA
engineers that that is what was in their expensive bottles sold to radio
stations. Other alcohol agents left a residue that would eventually arc over.
Don, W4CBS
Sent from Yahoo Mail on Android
On Sat, Jul 17, 2021
a (do not flood the board),
and dry the area after application. Make certain ALL the flux was
removed from the area - if there is any residue, it can be conductive,
leading to leakage paths. Let it dry and look for 'whitish' stuff. If
there is any, you have not done a complete job.
is
complete. While solder flux is non-conductive, the flux plus the
cleaner may be conductive leading to resistive leakage paths. If you can
see any white stuff on the board, you have not done a complete job.
73,
Don W3FPR
On 7/14/2021 6:41 PM, Peter Eijlander (PA0PJE) wrote:
Yes Jerry
And discard those "Amazon Special" PL-259s. Use only quality
connectors. It is not worth it to use off-spec connectors - you are
witness to the pain and heartache they can cause.
73,
Don W3FPR
On 7/11/2021 4:52 PM, Dave wrote:
If it were me, I'd replace the SO-239 on the tun
nd like to do the 'wrist roll' when
operating the paddles - that means I need to have the handle(s) about
1.5 inches above the table. Tony has several varieties of both single
lever and dual lever paddles - he is a a quality machinist.
73,
Don W3FPR
On 7/8/2021 6:31 PM, Julia Tuttle w
KRX3A level
should be available on the Elecraft website.
The capacitor is a low profile large value tantalum type. It is
soldered near the center of the board.
73,
Don W3FPR
On 7/5/2021 1:53 PM, Paul GACEK via Elecraft wrote:
Happy 4th to all those that celebrate it/care about it.
I have
godsend.
73,
Don W3FPR
On 7/3/2021 7:57 PM, jerry wrote:
On 2021-07-03 11:03, VA1CQ wrote:
Any tips on removing them would be appreciated.
*** Crush them with a pair of pointy vise-grips? Of course, I'd try
desoldering them first. Hold the heat on a bit longer than seems
necessary, be
bars solid on the ALC meter with the
5th bar flashing. You may have up to 3 audio level controls to work
with. It is best to start with them all set to mid-range, then adjust
from there.
73,
Don W3FPR
On 7/3/2021 5:35 PM, doug dietz wrote:
Guys
I have k3 with all the options available
whatever tool works to crush the relay
cases.
73,
Don W3FPR
On 7/3/2021 2:03 PM, VA1CQ wrote:
Hi Don,
I have discovered I installed K1 and K2 backwards. The location bar on
each relay is facing in the opposite direction ("down") from the other
relays. The manual Parts Placement Drawi
I would advise you to download and install the latest FTDI drivers from
the FTDI website.
My understanding is that Win 10 does no longer include the FTDI drivers.
73,
Don W3FPR
On 7/2/2021 10:03 PM, Mike Dodd wrote:
My K3s, KPA500, and KAT500 are connected to my Win 8.1 Pro PC, and
everything
F Probe on
W6 and align the bandpass filters for maximum RF voltage on each band.
73,
Don W3FPR
On 7/2/2021 8:54 PM, VA1CQ wrote:
Hi Geert,
Coincidentally, while troubleshooting today I was listening to relays!
There is a different sound depending on whether one relay clicks or
more than one c
Frank,
That sounds like the 'finger dimple' from Elecraft. I don't know if
they are still available.
If you have the piece that fell off, glue it back on - I used E6000
adhesive with great success.
73,
Don W3FPR
On 7/2/2021 3:13 PM, Frank Krozel wrote:
I ended up with a f
'tweek' the bandpass
filter a bit, but it should be very close to correct.
Your name and call on your posts please - I know your call is in your
email address, but your name would make it a bit more personal.
73,
Don W3FPR
On 7/1/2021 5:34 PM, VA1CQ wrote:
Further troubleshooting of
- for X5 and X6 you will have to settle for a single grounding wire on
each, but it should be near the bottom.
The K2ATOB instructions call for soldering on both sides of the crystals
near the bottom, but it does not contain any instructions about changing
the crystals.
73,
Don W3FPR
On 7/1/2021
Jerry,
Yes, there is a bit of compromise between LSB and USB on the carrier
null, but it should not be much. Settle for a compromise position.
73,
Don W3FPR
On 6/30/2021 10:06 PM, jerry wrote:
So I got up at 5:30 this morning and continued stuffing the SSB
adapter card. Finished it up this
the computers on my network.
Recently I have been buying computers pre-loaded with Win 10 Pro.
73,
Don W3FPR
On 6/30/2021 5:09 PM, Paul Jewell wrote:
Hi Don,
I should have given more details -
* Running linux
* ftdi drivers are all installed, and the port of /dev/ttyUSB0 is
installed
download them from the
FTDI website.
Double check your homebrew KXSER cable. Did you get the RXD and TXD
connections right?
All in all, it should work quite nicely.
73,
Don W3FPR
On 6/30/2021 4:14 PM, Paul Jewell wrote:
Good evening,
I am trying to find a wiring layout for the kxusb cable. I
"If it ain't spark gap, it ain't real ham radio." Nuff said.
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by:
Those NE-2s have a high breakdown level. OK for vacuum tube equipment,
but too high for semi-conductors.
73,
Don W3FPR
On 6/29/2021 2:16 PM, Ray wrote:
In the Early days we used a NE-2 for front end Protection…..
Ray WA6VAB K3
*From: *Frank Krozel <mailto:kg9hfr...@gmail.com>
Frank,
Yes, you still need to disconnect. The polyphasers protect against
large spikes, but smaller ones get through.
73,
Don W3FPR
On 6/29/2021 11:10 AM, Frank Krozel wrote:
Folks after Field day with another manufacturer’s radio, I have a new to me
K2/100 coming in two days to use as my
If he is close to an airfield (of any type), then there are height
restrictions - but if you can assure the powers that be that your
antenna is not higher than trees or other objects in the vicinity, you
can get FAA approval.
73,
Don W3FPR
On 6/28/2021 7:06 PM, John Marvin wrote:
Note, I
are tuned correctly.
Once you get the KSB2 option installed, you can enter the BFO
frequencies suggested in the manual and then proceed to do a more
precise dial and BFO calibration.
The DAC steps for the BFO limits the precision that you can achieve, but
10 to 20 Hz is achievable.
73,
Don
there is an offset if
you try to use CW - no offset with SSB.
73,
Don W3FPR
On 6/28/2021 1:05 PM, jerry wrote:
All,
OK, I did it. Made up a counter probe from a hunk of
rg316, crimped a couple of dupont female clips onto the end,
put them in a shell, squished a dab of hot melt glue between the
closest to the left side panel.
73,
Don W3FPR
On 6/28/2021 11:00 AM, jerry wrote:
Hello all,
I note that my new ( to me ) K2 is not well set up on the BFO for
the narrow CW filters. It's fine for the 1.5kHz one, but the audio
passband is too high for all the narrower ones - so I c
ncy is not constantly remembered,
so if one turns the VFO knob and immediately powers down, the frequency
may not be remembered. The VFO is remembered only after a few seconds
of not changing.
73
Don W3FPR
On 6/27/2021 5:39 PM, Rich WC3T wrote:
Dumb question, and I’m no K2 expert — but did y
Ted,
Try 'counting to ten' before powering down.
If you move the VFO just before powering down, the VFO frequency may not
have been written to EEPROM yet, the process is not immediate.
73,
Don W3FPR
On 6/27/2021 5:21 PM, eda...@aya.yale.edu wrote:
I just finished debugging a K2 I
,
Don W3FPR
On 6/26/2021 4:58 PM, VA1CQ wrote:
Don,
A logical suggestion. I already have made the RF Probe and it's ready
to use. I was hoping the cause of no power might be something simpler.
I will start troubleshooting in my next work session.
Murray VA1CQ
On 6/26/2021 5:34 PM
,
Don W3FPR
On 6/26/2021 4:21 PM, VA1CQ wrote:
I am just completing the build of K2 Serial No. 6397. Everything was
going perfectly with all receiver tests and adjustments. Everything is
in spec.
Then I started the transmitter tests. I set the output power control
for 2.0 watts. Beginning on 40
://www.qsl.net/wy3a/Replace_K2_Headphone_Jack.htm.
Of course, you likely do not have to replace the headphone jack, but the
disassembly instructions are the same.
73,
Don W3FPR
On 6/26/2021 8:39 AM, jerry wrote:
Just for yuks, I opened it up to seewhat if the SSB adapter had
been installed
Many filters constructed using the newer crystals do not have that tilt,
especially at narrow filter widths.
Wide filter widths do have both tilt and passband ripple.
Having aligned almost 2000 K2s, I can say this with certainty.
73,
Don W3FPR
On 6/25/2021 6:06 PM, Louandzip via Elecraft
Jerry,
Look at the crystals again - if they are marked 4.9136-S they are the
new ones.
73,
Don W3FPR
On 6/25/2021 5:25 PM, Don Wilhelm wrote:
Jerry,
Yes, those are the older crystals. The new ones have a "-S" suffix on
the label.
73,
Don W3FPR
On 6/25/2021 5:00 PM, jerry
akes that
task easy.
You will need the internal counter probe if one was not included with
your K2, Elecraft does sell a kit of parts.
I can give you help with the Dial Calibration and Filter alignment.
73,
Don W3FPR
On 6/25/2021 4:08 PM, jerry wrote:
Hello all,
My new ( to me ) K2 arriv
Jerry,
Yes, those are the older crystals. The new ones have a "-S" suffix on
the label.
73,
Don W3FPR
On 6/25/2021 5:00 PM, jerry wrote:
So - looking at the crystal filter: the crystals are labelled thusly:
ECSX
4.9136
China
...I'm guessing these are t
After referring to both the Elecraft K3 manual and Steve Cady's version,
I'm confused. Is there a simple way to wipe all the KAT3 tuning memories?
Either way yes or no, could you please walk me through it?
73 Don NA6Z
K3 #5495
_
Jerry,
You likely will need other upgrade kits, not just the K2ATOBKT.
The instructions for the K2ATOBKT shows all the associated upgrade kits.
Yes, wait until you have the radio in hand. The only way to know what
upgrade kits have been installed is by physical inspection.
73,
Don W3FPR
On
crystals (for both the base
K2 and the KSB2 adapter.
73,
Don W3FPR
On 6/22/2021 8:51 AM, jerry wrote:
Greetings,
Name is Jerry, call KF6VB. Been a ham since 1970. For some
strange reason, my interest in amateur radio always peaks at the
bottom of the sunspot cycle. No, I don
a Field Test version.
There were some FT changes which added a few components to the bottom of
the board, those should remain in place.
73,
Don W3FPR
On 6/21/2021 2:05 PM, K9SW wrote:
I recently bought a K2/10 and realized that the serial number is 100, which is
a low number. I recall
the halves of
the connector, that is seldom necessary.
73,
Don W3FPR
On 6/17/2021 6:54 PM, Rich wrote:
[K3} - K3 Powerpole
The positive (red) Powerpole plastic on my K3 broke while pushing it back on
my desk.
Has anyone replaced the plastic covers without taking the K3 apart? If so I
would l
when
he was transmitting a dirty signal, that might bring an end to this
problem. In the meantime, it is up to other operators to call out dirty
signals.
Straight Key Night were some drag out their 1950s and 1960s rigs may be
an exception to this "rule".
73,
Don W3FPR
On 6/14/20
PJH,
You must run the calibration routine anytime you install or uninstall
the roofing filter.
73,
Don W3FPR
On 6/12/2021 3:19 PM, PATRICK HICKS wrote:
I have 2 KX3s that I intend to use in 2 different locations. One is an older
one that has a roofing filter and the newer one does not. I
not
recall that as a mod.
73,
Don W3FPR
On 6/10/2021 5:37 PM, Mike Cizek W0VTT wrote:
Greetings,
I recently purchased a used XV222 that had some modifications done in the
local oscillator circuit. The construction was very sloppy, but transverter
works OK most of the time. Power output is
did not have any TMP jacks
available).
Where you mount the SubRX IF out jack on the rear panel is an effort and
a choice for the owner.
73,
Don W3FPR
On 6/10/2021 4:08 PM, Jeff Goldman wrote:
I am looking for any information on hooking up a P3 to the sub-receiver in a
K3S. Any help would
a barrel".
I know this does not compare the IC-7300 to the FTDX10, but I thought it
to be a point of interest to some.
I wonder how many will be comparing the K4 to the K3 with on the air
experiences.
73,
Don W3FPR
On 6/8/2021 7:00 PM, Richard wrote:
Assuming you're a casual r
nes, check back on the control
board at Q1, Q2, Q3 and Q4 to determine where the problem might be.
73,
Don W3FPR
On 5/27/2021 4:15 PM, Josh Gibbs wrote:
My K2 (SN: 4073) suffered a sudden problem yesterday. I didn't notice
anything happening - one minute it was working normally and the ne
low
reading.
73,
Don W3FPR
On 5/24/2021 5:52 PM, Erik Tkal wrote:
Hi Don,
Everything appears correct and in place, already used magnification to
check, and individual resistors all seem to measure correctly. I
still think it's my multimeter in auto mode. I went back and retried
the in
Since that is the case, check the value of the resistors and check out
the soldering under magnification.
73,
Don W3FPR
On 5/24/2021 3:08 PM, Erik Tkal wrote:
Hi Don,
Nope, D3 and D4 are correct, and the LEDs check out per the test
Erik,
Check and double check the orientation of the diodes. That is the most
likely reason for you measurement results.
73,
Don W3FPR
On 5/23/2021 5:39 PM, Erik Tkal wrote:
I just assembled the T1 kit, but am having an issue in the final check phase of
the Control Board.
"Resis
eoff.
73,
Don W3FPR
On 5/19/2021 6:54 PM, Louandzip via Elecraft wrote:
I count beats. One beat in 1 second and I'm off 1 Hz. One beat in two seconds
and I'm off 1/2 Hz. Easiest done if the side tone and received signal are
adjusted to be close in amplitude and there's little/
Ronnie,
Yes they do, but due to Covid-19 and short staffing, it may take a while.
If you did not direct your email to supp...@elecraft.com, it may take a
while to get it from one email address to another until it finally hits
support.
73,
Don W3FPR
On 5/19/2021 6:22 PM, Ronnie Hull wrote
pare it to the difference between pulling the plug on a computer as
opposed to properly shutting it down. The pulling of the plug may lose
some of the configuration and current operational state of the K3.
73,
Don W3FPR
On 5/12/2021 6:42 PM, Mark N2QT via Elecraft wrote:
Is there much danger
It is not. mailman.qth.net may have changed its posture on HTML, but I
doubt that they will allow attachments.
73,
Don W3FPR
On 5/12/2021 5:08 PM, Edward H Russell wrote:
This is html. Is it blank?
__
Elecraft mailing list
Home
If it is in HTML, I wonder why the mailman.qth.net HTML stripper let it
through.
Email in HTML normally comes through blank.
73,
Don W3FPR
On 5/12/2021 3:51 PM, DAVID HEWITT wrote:
- This mail is in HTML. Some elements may be ommited in plain text. -
Hello there!
sorry to bother you,do you
Doug,
Peer into the side of the KPA100 (the side where the coax and power
connections are) - If you see blue toroid cores, the upgrade has been
done. If you can only see red toroid cores in about the middle of the
board, the lastest update is not installed.
73,
Don W3FPR
On 5/11/2021 1:00
Larry,
The KPA100UPKT totally revamps the T-R switch section on the KPA100, so
the answer is yes.
There is a chance that there may be a nasty spur when on 40 meters - at
about 8 MHz if you do not have the upgrade.
73,
Don W3FPR
On 5/10/2021 4:04 PM, Larry Dodson via Elecraft wrote:
I
screws without dropping the lockwashers
(they will stay on the screws if you are careful)
73,
Don W3FPR
On 5/10/2021 10:54 AM, JOHN LAWRENCE via Elecraft wrote:
Hi
any hands on experiences detail that might be useful if I do it myself when the
kit arrives. Thanks
John, W1QS
Lou,
Download the K2 A to B instructions and inspect your K2 to see which
mods have been installed.
Physical inspection is the only way I know to do it.
73,
Don W3FPR
On 5/10/2021 8:21 AM, Louandzip via Elecraft wrote:
One thing that's holding me up is doing the research to figur
.
73,
Don W3FPR
On 5/9/2021 5:36 PM, Geert Jan de Groot wrote:
On 09/05/2021 20:54, elecraft-requ...@mailman.qth.net wrote:
Don, W3FPR used to do much of this work on K2 transceivers, but he has
retired from that role. Dave, W8FGU has assumed Don's role. Alan, W3DVX
also provides such ser
Jeff,
Either would be more that adequate. You could also use RG58 if that is
better for you.
It does not have to have the high voltage ratings of RG8, and RG58 is
more flexible than RG8X.
No need for overkill.
73,
Don W3FPR
On 5/9/2021 6:49 PM, w...@flashdog.us wrote:
Hi Everyone,
Quick
vely since the SNs had not yet been assigned. The original K2 SN
was assigned at random - 1 chance in 100 and I got 0020 in that draw.
73,
Don W3FPR
On 5/9/2021 6:12 PM, Dave Van Wallaghen wrote:
Wel Don, I don't know about all that. I just try and stump you once in
awhile 😜 and you know I
help Dave when he runs into a weird problem, but his requests
for assistance have fallen off to a trickle in the past 6 months - I
think he is fully 'on board' and quite capable.
73,
Don W3FPR
On 5/9/2021 5:36 PM, Geert Jan de Groot wrote:
On 09/05/2021 20:54, elecraft-requ...@m
base of Q1 (on the top of the board) and insert a 1k resistor across the
trace cut.
That will calm ALC problems with the KSB2, and otherwise will do no harm.
73,
Don W3FPR
On 5/8/2021 1:44 PM, M Bak wrote:
Today I finished the KSB2 adapter and installed it into my K2. It worked
first time but was
Waiting with breath like bait... ;)
-
Don
W6CZ
DM07bk
--
Sent from: http://elecraft.365791.n2.nabble.com/
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post
Phil,
You may want to check out the Behringer mixers even though they may have
more inputs than you need. I don't know if any of the inputs support
Bluetooth natively.
They are low in price and work well.
73,
Don W3FPR
On 4/26/2021 10:06 AM, Phil Kane wrote:
Really OT but where else
Sorry for the wasted email. Problem with Win 10 drivers.
Final score: NA6Z 1; Win10 0
73 Don NA6Z
K3 #5495
On Sun, Apr 25, 2021 at 4:19 PM Don Putnick wrote:
> I'm having problems controlling my K3 with applications under Win 10.
> Truth in lending: Win 10 is on the Bootcamp part
I can't on the Win
10 side, but the connection is established. N1MM is a mixed bag. I can read
and control the VCOs but I can't get the macros to send CW.
I'd appreciate any suggestions anyone has to offer. Not urgent but
frustrating. I have until Fie
I know that the T1 can’t be used to tune an antenna above 6 meters, but can
it be used in the bypass mode?
--
Sent from: http://elecraft.365791.n2.nabble.com/
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecra
and dirty side down.
73,
Don W3FPR
On 4/25/2021 9:27 AM, eda...@aya.yale.edu wrote:
I never took a drafting class nor anything like it in high school, yet its
absence never hurt me professionally. Making a straight line is not a skill
required of a
Frank,
Just take the top cover off and look between the upper 2D connectors and
the Front Panel board.
73,
Don W3FPR
On 4/25/2021 10:34 AM, Frank Krozel wrote:
Thanks Don, will check today.
I also need to figure out which K2 need those small 3/8”x3/8” rubber
spacers in-between the PC
e new
encoder.
Order the new knob from Elecraft - they no longer have the older knob.
With the new knob, you need 3 fiber washers stacked.
73,
Don W3FPR
On 4/25/2021 9:00 AM, Frank Krozel wrote:
I am looking for a tuning knob for a K2 SN 5630
If I recall there were two different sizes of shafts,
, making changes until the
customer and I were satisfied about what they wanted me to build.
73,
Don W3FPR
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post
Since the K3 has stereo output, I suggest you look at the West Mountain
Radio ComSpeakers. They do a good job.
My K3 had 2 Radio Shack mini speakers on it, and the KX3 uses the
ComSpeakers. Great in all respects.
73,
Don W3FPR
The original poster asked about plugging in both the speakers
Yes, They call it ComSpkr and it is priced at $39.95.
It is a pair of "computer" speakers, but it is shielded so it does not
buzz when RF is present.
73,
Don W3FPR
On 4/24/2021 11:50 AM, NJMike wrote:
Can you confirm the West Mountain ComSpeaker is
#58410-950?
Since I’m a new K3S
Since the K3 has stereo output, I suggest you look at the West Mountain
Radio ComSpeakers. They do a good job.
My K3 had 2 Radio Shack mini speakers on it, and the KX3 uses the
ComSpeakers. Great in all respects.
73,
Don W3FPR
On 4/23/2021 6:01 PM, Rick Bates, NK7I wrote:
Regardless of
Get a replacement from Elecraft.
Which radio?
73,
Don W3FPR
On 4/23/2021 3:27 PM, Steve Fox wrote:
Hi
Anyone care to recommend an internal speaker replacement?
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman
Carter,
Do you also have VOX active? With both PTT and VOX on, that will happen.
On 4/21/2021 9:57 AM, Carter Craigie wrote:
I am setting up my KX3 for FT8 using a SignaLink USB interface. My computer
runs Windows 10.
For PTT, I have checked the CAT option.
When I do the test for CAT and PTT
John,
Deposit 1/2 the price now, or deposit the full price.
73,
Don W3FPR
On 4/20/2021 1:57 PM, John Simmons wrote:
What is the difference between 'half dupl' and full dupl'?
__
Elecraft mailing list
Home: http://
.
73,
Don W3FPR
On 4/17/2021 1:41 PM, David Pratt wrote:
I would be pleased to hear from anyone who has a crystal oven for the XV
series of transverters. The Elecraft part number is E980076. The oven
in my XV144 has gone open circuit
ve
fewer uses for macros - the K3 does it for you by default.
73,
Don W3FPR
On 4/16/2021 8:01 PM, Bob Applegate wrote:
A number of people have asked what I am trying to do with the macros, so here
is a quick explanation. In a normal day I'm switching between CW, digital and
sideband freq
ect sideband - it will be remembered.
If you are entering the macro into a computer application, then ignore
my suggestion - I only operate "by the buttons".
73,
Don W3FPR
On 4/16/2021 6:18 PM, Bob Applegate wrote:
I’ve been trying to set up a macro to automatically choose the correct s
,
Don W3FPR
On 4/16/2021 1:46 PM, r...@wc3t.us wrote:
As you get a round tuit, will these nuances make it into the other models in
the KX-line? I always hear of the strident warnings of factory restores
hammering the hard-won calibration data and have counted my lucky stars that
I have not had
Tommy,
I highly recommend that you get the proper screws from Elecraft to be
certain they are the correct length.
Hardware store screw are normally not available in black, so why mess up
the appearance of your KX2 with zinc plated screws.
73,
Don W3FPR
On 4/13/2021 11:36 AM, Tommy Judson
101 - 200 of 16095 matches
Mail list logo