back on properly so keep the solder to a minimum.
Regards
Malcolm
G0MIC
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net
Can some one who has a pair of these tell me if there is any electronic noise
reduction circuitry in the headphones or is it by physical isolation only
please?
Sorry to be off topic
Malcolm
G0MIC
__
Elecraft mailing list
Home: http
ing the voltages when keying say 50 Watts. Measuring the drop
along
each wire of the cable should show where the problem lies.
Regards
Malcolm
G0MIC
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/ele
KRX3 module, still in original shipping package from Aptos. Would prefer
UK/European buyer. Email me off list for details.
73 Mal G4KFT
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.q
Downloaded HRD (again) and note that there is no support for the K3, the
only Elecraft radio is the K2. Has this been withdrawn? Seem to remember
my last play with HRD that the K3 was an radio option?
Mal G4KFT K3 #263
___
Elecraft mailing list
Post t
Ordered a K3 on 2nd May, nothing heard here either
Mal, G4KFT
Raj Dewan, N2RD wrote:
Now that is interesting. Vic G7PYR reports that his order placed on
May 4 is being filled. I ordered with 50% deposit on May 2 and I've
not even heard from them yet...
Raj, N2RD
[EMAIL PROTECTED] wrote
All of a sudden, I'm getting a strange icon on every band change. It
appears momentarily only. Looks like an antenna symbol with a bar across
the top.
Has anyone any idea what this icon represents, it's probably due to some
menu change I've inadvertently made, not seen it previously.
Thanks
Thank David, had already assigned a name to ANT1, this icon is still
present to the left of the antenna name. It's not causing any problems,
I'm just curious as to what the hell it is/
Thanks
David Pratt wrote:
In a recent message, Malcolm Rothwell <[EMAIL PROTECTED]> wrot
After seeing various posts on this subject, thought I'd give it a try.
Unfortunately when I opt for factory defaults and click on "Calibrate" I get
the following error message : E0400E3 ERR DSE on the K3 display and on the
K3 utility I see "DSP command response did not arrive". The radio is
perfor
values on the 80m bandpass and low pass. Looked for solder joints on L3,
L4, L16, L17. Checked filter settings. Any suggestions very welcome.
Thanks
Malcolm, K1VZ
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to
I found the error on 80m so problem now resolved. Now I have a 20m
problem!
Malcolm, K1VZ
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http
with heat or pulling but I think it
may also have been a component fault. No blame attached to anyone but hope
this helps others. Happy building. What a great radio!
73, Malcolm, K1VZ
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You
white thin film which
appears to be attached at LED ends of the diffuser only. Looking at the
instructions it appears to say that I should not remove any of these. Help
please. Do I remove the top one which looks awful, both or none?
Thanks
Malcolm, K1VZ
ate guidance.
Regards
Malcolm
G0MIC
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
14 matches
Mail list logo