Sticky timer; turn the K3 on at a set time each day.
Rick WA6NHC
Smell Czech correction happens
> On Apr 6, 2019, at 2:12 PM, Dick Dickinson wrote:
>
> Sticky Noise Blanker.through on/off cycle and band changes.
>
>
>
>
>
> Dick - KA5KKT
>
> _
Sticky Noise Blanker.through on/off cycle and band changes.
Dick - KA5KKT
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
The KX2 now allows 4 separate programmable functions when the "PFn" key is
pressed. That would be a nice feature on the K3 for the PF1 and PF2 buttons.
There are many times now when I disconnect the USB cable from the rig as I
have found a large (10 to 20 dB) increase in noise floor on some bands w
I use 0 through 9 on the K2 and K3 as permanent "jump to band;
configure appropriately" memories. This normally works great, but I have a
frustrating habit of accidentally pressing STORE or V->M when I mean to
press RCL or M->V, and there go my settings. I'm not expecting a K2
update :)
Did you try turning the VOX Delay down to zero?
Worked for me when running remotely!
73 Dwight NS9I
On 3/11/2016 1:12 PM, charlie carroll wrote:
I use the internal K3 message memories when operating as DX in an ssb contest.
One of the biggest problem I face is the delay both in initiating the
I am curious what you are you using the memories for? I really never
noticed any delay but during 300/hour rates I think it is way easier to
just to speak.
John KK9A
charlie carroll k1xx at k1xx.com
Fri Mar 11 13:12:02 EST 2016
I use the internal K3 message memories when operating as DX in an
I use the internal K3 message memories when operating as DX in an ssb contest.
One of the biggest problem I face is the delay both in initiating the message
(from an external application) and the delay between the end of the message and
back in the receive mode. From experiments, both of these
The KAT500 relay switch over between two in-band segments is driving
me nuts. A lot of DXpeditions on 160 use 1823.0Khz for transmit
listening up 1-5khz. Every time the K3 goes from A RX to B TX, and back
again, it involves a cur-chunk from the KAT500 whether the tuner is in
Auto or Manual. I
I wonder if the following is something that is possible to implement via a
change in firmware:
Allow an antenna to be active on RX Out regardless of whether the K3 is
turned on or not?
73, Yngvi TF3Y
--
http://www.tf3y.net
__
Elecraft
Let's close this thread for now in the interest of keeping list traffic volume
under control.
73,
Eric
List moderator etc.
elecraft.com
On 2/19/2015 2:44 PM, Rick Bates, WA6NHC wrote:
Tap 5 to make it sticky (repeatable) the next time period (which could be
hourly too?)
Rick, WA6NHC
On Feb 1
Rohmer; elecraft@mailman.qth.net
Subject: Re: [Elecraft] Elecraft K3 Feature Request - Main: ALARM - Tap 4 to
activate reminder to ID
I kinda like that one
From: Dwayne Rohmer
To: elecraft@mailman.qth.net
Sent: Thursday, February 19, 2015 1:25 PM
Subject: [Elecraft] Elecraft K3 Feature
Tap 5 to make it sticky (repeatable) the next time period (which could be
hourly too?)
Rick, WA6NHC
iPad = small keypad = typos = sorry ;-)
> On Feb 19, 2015, at 10:25 AM, Dwayne Rohmer wrote:
>
> K3 Feature Request
>
> MAIN: ALARM - Tap 4 to activate reminder to ID (two beeps every ten minu
Years ago, one of the Heath accessories [to the SB3xx twins I think] had
a large [like 2.5 cm high] "ID" indicator that came on every 10 min.
Don't remember how it was reset, PTT?
MAIN:ALARM - Tap 5 to activate Conelrad monitor.
73,
Fred K6DGW
- Northern California Contest Club
- CU in the 50
> To: Dwayne Rohmer; elecraft@mailman.qth.net
> Subject: Re: [Elecraft] Elecraft K3 Feature Request - Main: ALARM - Tap 4 to
> activate reminder to ID
>
> I kinda like that one
> From: Dwayne Rohmer
> To: elecraft@mailman.qth.net
> Sent: Thursday, February 19, 2015 1:25 PM
&g
Elecraft
Sent: Thursday, February 19, 2015 12:50 PM
To: Dwayne Rohmer; elecraft@mailman.qth.net
Subject: Re: [Elecraft] Elecraft K3 Feature Request - Main: ALARM - Tap 4 to
activate reminder to ID
I kinda like that one
From: Dwayne Rohmer
To: elecraft@mailman.qth.net
Sent: Thursday, February
I kinda like that one
From: Dwayne Rohmer
To: elecraft@mailman.qth.net
Sent: Thursday, February 19, 2015 1:25 PM
Subject: [Elecraft] Elecraft K3 Feature Request - Main: ALARM - Tap 4 to
activate reminder to ID
K3 Feature Request
MAIN: ALARM - Tap 4 to activate reminder to ID (two
K3 Feature Request
MAIN: ALARM - Tap 4 to activate reminder to ID (two beeps every ten minutes)
73,
Dwayne WV5I
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post
QTA my "feature request." Thanks Matt, exactly what I was looking for.
73,
Fred K6DGW
- Northern California Contest Club
- CU in the 50th Running of the Cal QSO Party 3-4 Oct 2015
- www.cqp.org
On 2/4/2015 4:31 PM, Matt Zilmer wrote:
I think SPLIT SV does this. It should preserve your RIT an
I think SPLIT SV does this. It should preserve your RIT and XIT
settings on a per-band basis. You'll find the setting at
CONFIG:SPLT SV.
73,
matt
W6NIA
On Wed, 04 Feb 2015 16:00:17 -0800, you wrote:
>Would it be possible to have an option that will either work the way it
>does now, or wil
Would it be possible to have an option that will either work the way it
does now, or will preserve the SPLIT setting if you make a quick QSY to
another band and then come back?
I'm officially on the "Didn't Get The 'UP' Memo" list as a result of a
quick check of 30 and return to 20. I did rea
Override / Bypass for RX and TX EQ. One button macro or similar.
73,
Dick - KA5KKT
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft
The "put the K3 in TEST mode" has the additional advantage of requiring no
additional work for someone who just turns the VOX off when not actively
using the powered-up radio. Just push-and-hold a different button.
--
*Michael D. Adams* (N1EN)
Poquonock, Connecticut | m...@n1en.org
On Thu, Mar
DUH,
what an excellent idea, and such a simple fix
I with draw my misguided request
(optional of course, didn't realize I needed to say that)
and I apologize for any fear of change it may have fostered in some
GB all
On 3/21/2013 3:44 PM, Don Wilhelm wrote:
Sam,
Could I offer a suggestion?
Maybe I'm misunderstanding the request, but it doesn't seem like
a good idea to me.
Imagine I'm on 6m during a contest with CW in SSB enabled.
I'm keying the radio with the computer, so I have the VOX-QSK
button set to PTT. I'm on phone, but I want to answer someone
on CW. So now I won't be able
mail.com]
> Sent: Thursday, March 21, 2013 1:45 PM
> To: elecraft@mailman.qth.net
> Subject: [Elecraft] K3 feature request 'CW in SSB' change
>
> I run my K3 with 'CW in SSB' enabled
> this is found under CONFIG: CW WGHT
> Tap 1 to select SSB -CW (default) or S
craft-boun...@mailman.qth.net] on
behalf of Sam Morgan [k5oai@gmail.com]
Sent: Thursday, March 21, 2013 1:45 PM
To: elecraft@mailman.qth.net
Subject: [Elecraft] K3 feature request 'CW in SSB' change
I run my K3 with 'CW in SSB' enabled
this is found under CONFIG: CW WGHT
Tap 1
Sam,
Could I offer a suggestion? Hold the right side of the mode button to
put the K3 into TX TEST to prevent any RF from going out if the K3 is
falsely triggered into transmit.
73,
Don W3FPR
On 3/21/2013 2:45 PM, Sam Morgan wrote:
I run my K3 with 'CW in SSB' enabled
this is found under C
I use CW when in SSB when on 6m a lot, but I jeep the paddles in a
clear area where nothing can touch them except my thumb and
forefinger. Even then I bump them anyway.
Joe is right! We don't need changes to the K3 to protect us from
making mistakes.
73,
Tom
Amateur Radio Operator N5GE
ARRL Lif
I wholeheartedly agree with Joe, such a change would completely remove the
value of the feature.
73 Stephen G4SJP
On 21 March 2013 19:13, Joe Subich, W4TV wrote:
>
> Please *DON'T!* disable CW in SSB when SSB VOX is off. I never use
> VOX on phone and use CW in SSB regularly. This requested
Please *DON'T!* disable CW in SSB when SSB VOX is off. I never use
VOX on phone and use CW in SSB regularly. This requested change
would break CW in SSB for anyone who does not use VOX on phone.
73,
... Joe, W4TV
On 3/21/2013 2:45 PM, Sam Morgan wrote:
I run my K3 with 'CW in SSB' enabl
I run my K3 with 'CW in SSB' enabled
this is found under CONFIG: CW WGHT
Tap 1 to select SSB -CW (default) or SSB +CW (allows CW in SSB modes)
My problem is, while in SSB,
I often use the [VOX-QSK] button to turn the mike/vox off,
because I am trying to prevent any unintended transmissions.
all
- N6KR, Elecraft
Subject: [Elecraft] [K3] Feature Request
If you activate Noise Reduction (NR) on a mode (like CW), NR is on for all
modes on that band. Request NR to follow both mode and band. For example,
if you have NR selected for 40m CW, and change to LSB, NR is OFF (unless
previously
If you activate Noise Reduction (NR) on a mode (like CW), NR is on for
all modes on that band. Request NR to follow both mode and band. For
example, if you have NR selected for 40m CW, and change to LSB, NR is
OFF (unless previously activated for that mode).
Thanks,
- 73, John, N0TA
___
While we're talking about feature requests for the K3,
I'd like to have the possibility to have the text decode in the vfoB
area stay there, and not quickly return to displaying frequency as soon
as the other station stops transmitting. An additional entry for the
DISP menu should be ok. If this f
: [Elecraft] K3 feature request, separate monitor tx-audio levels for
speakers and line-out
Recording of TX audio is possible since:
MCU 2.72 / DSP 1.98, 12-9-2008
Misc. Changes:
** LINE OUT INCLUDES TX AUDIO: LINE OUT (*nor* menu setting) now includes
transmit sidetone and speech/data monitor audio
Recording of TX audio is possible since:
MCU 2.72 / DSP 1.98, 12-9-2008
Misc. Changes:
** LINE OUT INCLUDES TX AUDIO: LINE OUT (*nor* menu setting) now includes
transmit sidetone and speech/data monitor audio.
The monitor audio level is the same for the speakers (headphone) as for the
line-out
> haven't noticed that effect on my K3 and actually when just tested it
> now I don't hear anything other than a very faint click when the
> speaker switches off (I have PF2 programmed to toggle SPKR+PH). Maybe
> it's only on some K3's?
Toggle SPKR+PH with audio (e.g. WWV) at normal listening lev
Joe,
On 9 March 2012 22:29, Joe Subich, W4TV wrote:
]What Wayne would need to do is mute the speaker (shutdown the speaker
> amplifier) during transmit - and only for voice (AM, FM, SSB) modes.
> However, if you notice the shutdown behavior of the speaker amplifier
> it does not turn off instant
> I wonder if it could be done in the firmware, if it's possible, I'd
> appreciate an entry on the todo list :)
Headphone and Speaker audio share a common source (the same digital to
analog converter). There is no a separate audio feed for headphone and
speakers (K3 Schematics package, pg 28 and
I guess the subject line says it all - I would like to hear my audio
feedback in the headphones but not through the speaker, so as to not create
distortion/feedback, I wonder if it could be done in the firmware, if it's
possible, I'd appreciate an entry on the todo list :)
Any comments/suggestions
To go from CW to SSB requires no knob spinning at all,
Just set two of the memory buttons, one for each mode,
and they are band dependent so each band has its own
settings. That way it changes modes, filters, freq etc all
in one push of the button.
Operates somewhat like band stacking, if you w
Greetings -- This is probably well known to mose but for those who may be
interested in changing frequencies/modes within a band...What I do is assign
each band to a button 160-10 -- buttons 1 thru 9. (6 meters on 0). Then
when I am on a given band, I use the DVR/memory buttons to save additional
I also would very much like to have a feature like this.
--
View this message in context:
http://elecraft.365791.n2.nabble.com/K3-feature-request-auto-changing-tuning-rate-tp7339826p7342864.html
Sent from the Elecraft mailing list archive at Nabble.com.
___
I use direct frequency entry: quick and simple.
Ron AC7AC
-Original Message-
i do tire of spinning that know from ssb to cw.
what's the harm if it can be shut off??
pse ...when you have some spare time wayne
bill ny9h/3
10:41 AM 3/3/2012, Jim McDonald wrote:
>I would lik
i do tire of spinning that know from ssb to cw.
what's the harm if it can be shut off??
pse ...when you have some spare time wayne
bill ny9h/3
10:41 AM 3/3/2012, Jim McDonald wrote:
>I would like that too. I think either Icom or Ten-Tec that does that.
>
>Icom does a good job on tu
If it's selectable and I can turn it off, fine. My FT-847 does this and
I hate it. K3 works just fine for me, however I get only one vote.
73,
Fred K6DGW
TDY Lake Havasu City AZ [until tomorrow]
On 3/3/2012 3:51 PM, Don Wilhelm wrote:
> The K3 tuning rate is already selectable per mode. See t
I would like to see that function as well. User selectable of course, so no
one would go crazy.
73 de Sebastian, W4AS
On Mar 3, 2012, at 11:16 AM, Joe Subich, W4TV wrote:
>
> On 3/3/2012 10:51 AM, Don Wilhelm wrote:
>> The K3 tuning rate is already selectable per mode. See the Config
>> men
On 3/3/2012 10:51 AM, Don Wilhelm wrote:
> The K3 tuning rate is already selectable per mode. See the Config
> menu for VFO CRS.
It's not the coarse rate that is an issue for me, although it would
certainly be nice for it to step up to 1 KHz if I really spun the
VFO. What I'd prefer is ability t
I'd never use it, but if it can be added and menu selectable (on/off),
what the heck...no skin off my back.
What I do, if want to make a big frequency excursion on the same
band/mode is simply use the "keypad" to enter the frequency in the
range I want to target. But honestly, since I mostly use
The K3 tuning rate is already selectable per mode. See the Config menu
for VFO CRS.
In addition, there are the FINE/COARSE and RATE buttons to help you with
the tuning rate.
Please -- no dynamic tuning for me, it drives me crazy.
73,
Don W3FPR
On 3/3/2012 10:41 AM, Jim McDonald wrote:
> I wo
I would like that too. I think either Icom or Ten-Tec that does that.
Icom does a good job on tuning rates, with a slow rate for CW and RTTY
(switch selectable) and a faster rate for SSB.
I change the K3's tuning rate for CW/RTTY to 1 kHz and back to 2 kHz for SSB
with the same with a macro in D
When spinning the dial, how about an option that it kicks into FAST
automatically after a few spins above a certain rate?
Barry W2UP
--
View this message in context:
http://elecraft.365791.n2.nabble.com/K3-feature-request-auto-changing-tuning-rate-tp7339826p7339826.html
Sent from the Elecraft mai
Sent: Saturday, July 02, 2011 11:54 AM
To: W6SX Hank Garretson
Cc: elecraft@mailman.qth.net
Subject: Re: [Elecraft] K3 Feature Request
Neat idea, Hank!
On Fri, Jul 1, 2011 at 4:23 PM, W6SX Hank Garretson wrote:
>
> It would be wonderful if there were a CONFIG option to have CWT SPOT
>
Neat idea, Hank!
On Fri, Jul 1, 2011 at 4:23 PM, W6SX Hank Garretson wrote:
>
> It would be wonderful if there were a CONFIG option to have CWT SPOT
> zero beat using RIT instead of VFO A. This would be very useful
> during contests when CQing.
>
>
--
Rick Tavan N6XI
Truckee, CA
__
It would be wonderful if there were a CONFIG option to have CWT SPOT
zero beat using RIT instead of VFO A. This would be very useful
during contests when CQing.
73,
Hank, W6SX
Mammoth Lakes, California
Elevation 8083 feet in John Muir's Range of Light
_
Chasing a rare one operating split on RTTY, I will use the SUB RX and two
MMTTY windows so that I can see what's going on up in frequency. I'll have
the bandwidth narrow on VFO A and wide on the SUB RX. Sometimes I'll hunt
for a clear spot and sometimes I'll hunt for the station being worked.
Occa
Behalf Of Edward Dickinson, III
Sent: Friday, January 28, 2011 8:22 AM
To: Elecraft Reflector
Subject: Re: [Elecraft] K3 Feature Request
No.
73,
Dick - KA5KKT
-
David Gilbert wrote:
You&#x
No.
73,
Dick - KA5KKT
-
David Gilbert wrote:
You're kidding, right?
On 1/27/2011 7:30 PM, Edward Dickinson, III wrote:
> 10 Minute Timer - Sound, 'Beep, Beep, Beep.' Alternate, Flash or Dim
I sure hope so!
Gary
On Fri, Jan 28, 2011 at 5:34 PM, David Gilbert wrote:
>
> You're kidding, right?
>
>
>
> On 1/27/2011 7:30 PM, Edward Dickinson, III wrote:
>> 10 Minute Timer - Sound, 'Beep, Beep, Beep.' Alternate, Flash or Dim
>> Display and/or Panel Lights. Reset Timer. Countdown on cl
You're kidding, right?
On 1/27/2011 7:30 PM, Edward Dickinson, III wrote:
> 10 Minute Timer - Sound, 'Beep, Beep, Beep.' Alternate, Flash or Dim
> Display and/or Panel Lights. Reset Timer. Countdown on clock display.
>
>
> 73,
> Dick - KA5KKT
>
>
> ___
-Original Message-
From: Edward Dickinson, III [mailto:edd...@windstream.net]
Sent: Thursday, January 27, 2011 9:50 PM
To: 'elecraft@mailman.qth.net'
Subject: Re: [Elecraft] K3 Feature Request
...as a reminder for requisite station identification.
73,
Dic
Why would you want this?
On Thu, 2011-01-27 at 21:30 -0500, Edward Dickinson, III wrote:
> 10 Minute Timer - Sound, 'Beep, Beep, Beep.' Alternate, Flash or Dim
> Display and/or Panel Lights. Reset Timer. Countdown on clock display.
>
> 73,
--
73
Brendan EI6IZ
___
10 Minute Timer - Sound, 'Beep, Beep, Beep.' Alternate, Flash or Dim
Display and/or Panel Lights. Reset Timer. Countdown on clock display.
73,
Dick - KA5KKT
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elec
The only change in f/w was to the S-Meter calibration on 144 Mhz. there
was no change in sensitivity and the gain of the K144XV is fixed in h/w.
We are revisiting the cal level for the S-Meter on 144 MHz.
73, Eric
www.elecraft.com
---
On 11/10/2010 5:36 AM, w...@comcast.net wrote:
> Now that th
Now that the K144XV is available and a lot of us are planning to use it to
drive microwave transverters, it would be really nice if there was some way to
easily adjust IF gain. I know there was a gain change after 3.97 so it appears
this is available in the firmware. Is there a way that along wi
transmitter site in San
Antonio before Waterman sold the stations for a much higher
calling in Ham Radio!
I coudda been a contendah on 3.625 with that box! :)
-lu-w4lt-
Message: 25
Date: Wed, 6 Oct 2010 09:55:06 -0400
From: "George & Jan"
Subject: Re: [Elecraft] K3 Feature Reques
Good information on the Symmetra-Peak and phase rotation/scrambling
can be found here: http://www.w3am.com/8poleapf.html and a discussion
of AM symmetry with info on the "all pass filter" (phase rotation)
here: http://www.tonnesoftware.com/appnotes/allpass/allpass.html.
I suspect the rotation wou
Years ago in a land far far away we discontinued using the Semetra-Peak
(sp??) on AM in favor of the then new CBS Labs audio processers (
Audimax/Volumax (sp??)) which did a much better job of increasing the
average modulation with far fewer artifacts.
We did retain the boom mic phase reversal s
using electrets
on AM.
If a phase scrambler were part of the K3's DSP, any thought as to how much
DSP resource utilization is required?
Paul, W9AC.
- Original Message -
From: "Tim Tucker"
To:
Sent: Wednesday, October 06, 2010 12:34 AM
Subject: Re: [Elecraft] K3 Feature Req
> >
> > -lu-w4lt-
> >
> > Message: 37
> > Date: Tue, 05 Oct 2010 17:39:37 -0700
> > From: Jim Brown
> > Subject: Re: [Elecraft] K3 Feature Request
> > To: elecraft@mailman.qth.net
> > Message-ID:<4cabc549.6000...@audiosystemsgroup.com>
> &
> Message: 37
> Date: Tue, 05 Oct 2010 17:39:37 -0700
> From: Jim Brown
> Subject: Re: [Elecraft] K3 Feature Request
> To: elecraft@mailman.qth.net
> Message-ID:<4cabc549.6000...@audiosystemsgroup.com>
> Content-Type: text/plain; charset=ISO-8859-1; format=flowed
>
>
Or, he could scour E-Bay for a Kahn Symetra-Peak!
-lu-w4lt-
Message: 37
Date: Tue, 05 Oct 2010 17:39:37 -0700
From: Jim Brown
Subject: Re: [Elecraft] K3 Feature Request
To: elecraft@mailman.qth.net
Message-ID: <4cabc549.6000...@audiosystemsgroup.com>
Content-Type: text/plain; charset=ISO-
On 10/5/2010 5:58 PM, Tim Tucker wrote:
> OK, thanks for the education. I'm not an RF engineer, but every product on
> the market I've come across (doesn't mean much) and discussion I've read
> (start withhttp://www.nu9n.com/am.html) calls what I'm talking about as
> phase inversion. They could
OK, thanks for the education. I'm not an RF engineer, but every product on
the market I've come across (doesn't mean much) and discussion I've read
(start with http://www.nu9n.com/am.html) calls what I'm talking about as
phase inversion. They could all be using the wrong term for all I know.
I c
On 10/5/2010 5:11 PM, Tim Tucker wrote:
> incorrect phase orientation
The correct word to say what you mean is POLARITY, NOT PHASE. Phase is
a continuously valued function, and has the units of degrees. Polarity
is the word that describes whether the waveform is inverted or not.
Changing the
For AM users, could we get the ability to invert the voice phase as a
feature of the K3? This would allow us to make sure that the audio phase
orientation is correct where the positive peaks are always greater than the
negative peaks. Even better, it would be cool if the rig could auto detect
an
The CW to Data is a VERY neat feature. Nice way to be able to work RTTY with
my currently minimal setup. However, the 4 second idle at the end of the
xmsn is WAY too long. I understand the ..-- option to end it, but a CONFIG
setting to adjust it would be great to have.
Tnx,
Barry W2UP
--
View
...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Tom W8JI
Sent: Friday, July 23, 2010 6:41 AM
To: Brett Howard; Bob Naumann
Cc: elecraft@mailman.qth.net; 'Andy Wood'
Subject: Re: [Elecraft] K3 Feature Request - Stopping CW Memory Playback
with PTT
> While t
From: Gary Gregory [mailto:garyvk...@gmail.com]
Sent: Friday, July 23, 2010 4:44 AM
To: Brett Howard
Cc: Bob Naumann; elecraft@mailman.qth.net; Andy Wood
Subject: Re: [Elecraft] K3 Feature Request - Stopping CW Memory Playback
with PTT
Andy,
If tapping the Footswitch (PTT) stops transmitting
> While this is true I still feel that any KEY_IN source be it PTT or VOX
> or the paddles it should interrupt the memory keyer.
Makes total sense to me. Any call for another transmission source, VOX, PTT,
external key line input, or paddles, should halt automatic transmissions.
__
;m sure
> you'd
> > find more convenient.
> >
> > 73,
> >
> > Bob W5OV
> >
> >
> >
> > -Original Message-
> > From: elecraft-boun...@mailman.qth.net
> > [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Andy Wood
> 73,
>
> Bob W5OV
>
>
>
> -Original Message-
> From: elecraft-boun...@mailman.qth.net
> [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Andy Wood
> Sent: Thursday, July 22, 2010 9:57 PM
> To: elecraft@mailman.qth.net
> Subject: [Elecraft] K3
e CW which I'm sure you'd
find more convenient.
73,
Bob W5OV
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Andy Wood
Sent: Thursday, July 22, 2010 9:57 PM
To: elecraft@mailman.qth.net
Subject: [Elecraft
I have recently entered into the world of CW and participated in my first
contest using both SSB and CW modes. I noticed that you cannot stop the CW
memory playback by activating the PTT (either from a microphone attached to
the front panel or a footswitch plugged in the rear). It could only be
st
One would think we would have automatic offsets. Can't be that hard to do.
Keith, K5ENS
--
View this message in context:
http://elecraft.365791.n2.nabble.com/K3-Feature-request-Repeater-Offset-Or-not-saved-per-VFO-tp5258091p5265008.html
Sent from the Elecraft mailing list archive at Nabble.co
Ditto.
Bill
K9YEQ
K2 and KX1 field tester, K3 and modules
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Jeff Cochrane -
VK4BOF
Sent: Monday, July 05, 2010 6:35 PM
To: elecraft@mailman.qth.net
Subject: [Elecraft] [K3
Hi everyone,
I don't know if this has been asked for before, nor do I know if indeed
it can be implemented but I'd like to see each VFO save its splits etc
when changing between VFO A & B.
To illustrate what I mean, I currently have 146.675MHz FM with a -600KHz
offset setup in VFO A.
I also ha
...@woodtech.net.au]
Sent: Sunday, June 20, 2010 9:54 PM
To: elecraft@mailman.qth.net
Subject: [Elecraft] K3 Feature Request - Independant Selection of Mic Gain
F/R
It would be nice to be able to independently select mic gain for front or
rear panel input. Currently, changing one also changes the other
p...73
>
>
>
>
>
>
>> Date: Mon, 21 Jun 2010 05:46:33 -0700
>> From: k...@comcast.net
>> To: elecraft@mailman.qth.net
>> Subject: [Elecraft] K3 Feature request
>>
>>
>> If you happened to read W3IZ's review of the FTDX9000MP in the Ju
> The contour...
>
> The reason I chose 400Hz is because unlike the contour which can variably
> move through the entire pass band area (600Hz - 900Khz) , with the K3 you
> only get a specific Freq. settings for each EQ setting.
In CW mode you also have DUAL PB which tracks your PITCH setting.
ady...
If you need further explaination please feel free to email me off the group...73
> Date: Mon, 21 Jun 2010 05:46:33 -0700
> From: k...@comcast.net
> To: elecraft@mailman.qth.net
> Subject: [Elecraft] K3 Feature request
>
>
> If you happened to read W3IZ'
On Mon, 21 Jun 2010 05:46:33 -0700 (PDT), Mike K2MK
wrote:
Even though it's a review, it sounds like marketing gibberish to me.
I get the same effect when using the .05 DSP CW filter in my 9 lb K3.
BT 73 ES GUD LUK
DE N5GE,
QCWA LIFE MEMBER 35102 AR SK
n...@n5ge.com
http://www.n5ge.com
>
>If
Andy,
I use DXLab's Commander, its rig control module, with its user-defined
sequences to do this. They are DXLab's equivalent of K3 macros. I have one
to switch between the two mic inputs and set the TXEQ for each.
My setup has a PR781 on the front input and a Heil Proset Plus on the rear.
I h
Er, try "xfil"? Or the "width" knob?
;)
73,
LS
W5QD
--
View this message in context:
http://elecraft.365791.n2.nabble.com/K3-Feature-request-tp5204093p5204192.html
Sent from the Elecraft mailing list archive at Nabble.com.
__
Elecraft
If you happened to read W3IZ's review of the FTDX9000MP in the July QST you
will find an interesting comment on page 46. I don't know what it is but I
want it on my K3. Here's the quote:
"When activated, the contour acts like a super duper ninja CW filter that
makes the desired signal sound as if
Thanks Dick. I didn't think of that possibility.
Andy VK4KY
--
View this message in context:
http://elecraft.365791.n2.nabble.com/K3-Feature-Request-Independant-Selection-of-Mic-Gain-F-R-tp5202780p5202888.html
Sent from the [K3] mailing list archive at Nabble.com.
_
You might be able to use a pair of command macros to set the gain and
select front or rear microphone.
This isn't quite what you asked for, but one of the motivations for
offering command macros was to allow you to do something like this.
Dick, K6KR
Sent from my iPhone
On Jun 20, 2010, at 7
It would be nice to be able to independently select mic gain for front or
rear panel input. Currently, changing one also changes the other. It would
be nice to be able to set, say, rear panel input to low gain (rP.L) and
front panel input to high gain (FP.H) independently. I find the
computer-type
On Thu, 17 Jun 2010 10:12:53 -0700 (PDT), pd0psb wrote:
Paul,
Thank you for the correction. After reading the wiki link I realized that my
graphic artist and typesetter father was wrong when he told me that!
BT 73 ES GUD LUK
DE N5GE,
QCWA LIFE MEMBER 35102 AR SK
n...@n5ge.com
http://www.n5ge
>If you wish to continue this discussion with me please, let's do it through
>private emails, not on the reflector.
Tom, I'v sent you the qwerty link privately.
But this topic was about a query, not qwerty :-)
The query was about a scalable IF gain/AGC threshold, compensating the
higher bandnois
1 - 100 of 182 matches
Mail list logo
