We've now double checked this, and we have confirmed that the KXV3 pin length
has -not- changed between the KXV3A and the KXV3B. It is not necessary to trim
the pins during installation.
Its always been a tight fit, but not too difficult, to install this board set
as an upgrade. We checked
Last night I installed the new KXV3B board into my K3. Yes, the pins are
just a bit long - maybe 1/16 inch. Just long enough that the pins don't
clear the J66 socket as stated in the installation instructions.
But after several tries, I was finally able to do it without clipping the
leads or
I just removed the KIO3 modules and the rear panel to avoid having to
cut pins or bend boards. The fan panel had to be removed to access a
screw holding the rear panel to the KPA100 shield though.
Mike
KI0HA
On 6/16/2015 9:00 AM, NW0M wrote:
Last night I installed the new KXV3B board into
Subject: Re: [Elecraft] K3 KXV3B install problems
Thanks to Jim and Drew for the help.
I talked to Elecraft support.
I tried bending the pins, loosening the side and back panels, pins were
just
too long. With the KXV3B lined up and in position, and with the pins
behind
the header, the pins touched
, Fred, AE6QL
-Original Message-
From: Wayne Burdick n...@elecraft.com
Sent: Jun 12, 2015 11:08 AM
To: Udo Langenohl - DK5YA dk...@dk5ya.de
Cc: elecraft@mailman.qth.net
Subject: Re: [Elecraft] K3 KXV3B install problems
Hi Udo,
No one would ever be black listed, etc. We're just ramping up
Udo, I often have things arrive from Elecraft
without having received a shipping notice.
Seems odd, but not to worry :-)
73, Phil W7OX
On 6/12/15 12:10 PM, Udo Langenohl - DK5YA wrote:
Item is en route since June 10, says Elecraft
via support desk. Keeping my fingers crossed.
For whatever
: elecraft@mailman.qth.net
Subject: Re: [Elecraft] K3 KXV3B install problems
Hi Udo,
No one would ever be black listed, etc. We're just ramping up on multiple
products and options simultaneously, and there may be some minor delays on specific items.
73,
Wayne
N6KR
On Jun 12, 2015, at 12:52 AM
Langenohl - DK5YA dk...@dk5ya.de
Cc: elecraft@mailman.qth.net
Subject: Re: [Elecraft] K3 KXV3B install problems
Hi Udo,
No one would ever be black listed, etc. We're just ramping up on multiple
products and options simultaneously, and there may be some minor delays on
specific items.
73,
Wayne
N6KR
I'm I alone or am I black listed?
I really doubt you're blacklisted, but you are not alone. Check your
spam filter. Has your email system decided that the Elecraft reply was
spam?
Mark AD5SS
On Fri, Jun 12, 2015 at 2:52 AM, Udo Langenohl - DK5YA dk...@dk5ya.de wrote:
Lucky you are, Emory.
: Re: [Elecraft] K3 KXV3B install problems
Thanks to Jim and Drew for the help.
I talked to Elecraft support.
I tried bending the pins, loosening the side and back panels, pins were
just
too long. With the KXV3B lined up and in position, and with the pins
behind
the header, the pins touched
Having problems with install of the KXV3B upgrading from a KXV3A.
The pins are two long on the KXV3B, with BNC connectors up as far as they will
go in the rear slot?
I tried putting the pins in tilting the board with the BNC connectors not out
of the slot, it was too much of an angle, they will
The KXV3 boards are a tight fit. I've had mine in and out a few times
(replaced blown pin diodes) and finally figured out that I needed to
file the square cutout in the frame a bit at the top corners in order to
let the BNC jacks clear; I rounded the corners slightly with a needle file.
Also,
On Thu,6/11/2015 12:11 PM, ejk...@gmail.com wrote:
Having problems with install of the KXV3B upgrading from a KXV3A.
The pins are two long on the KXV3B, with BNC connectors up as far as they will
go in the rear slot?
I tried putting the pins in tilting the board with the BNC connectors not out
the new firmware.. thanks and 73
Emory WM3M
-Original Message-
From: Jim Brown
Sent: Thursday, June 11, 2015 4:12 PM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] K3 KXV3B install problems
On Thu,6/11/2015 12:11 PM, ejk...@gmail.com wrote:
Having problems with install of the KXV3B
@mailman.qth.net
Subject: Re: [Elecraft] K3 KXV3B install problems
Thanks to Jim and Drew for the help.
I talked to Elecraft support.
I tried bending the pins, loosening the side and back panels, pins were just
too long. With the KXV3B lined up and in position, and with the pins behind
the header, the pins
15 matches
Mail list logo