Hi Curt,
Do you have the internal ATU in your K3s?
If so, disable it by putting it in Bypass mode
and repeat your experiment.
Does the Forward power meter show any
output power, and can you confirm the
actual output power with an external power
meter?
If you still have a very high SWR into a du
With a verified good dummy load and on any/all bands, using antenna one or
antenna two, I have a SWR reading of 99.9. I see no charred components.
It has not had a lightning strike Newest download has been installed. Can
anyone provide insight or direction for a solution?
N5CW
Curt
___
On 3/22/2024 7:07 PM, Carol Richards wrote:
Hello all,
I wish to thank the few ops who responded to my initial request for help in
getting my K3S to key. Unfortunately, I still have had no luck in curing my
problem. Since I can’t seem to get any locals in nj to help, I am hoping
someone out
Hello all,
I wish to thank the few ops who responded to my initial request for help in
getting my K3S to key. Unfortunately, I still have had no luck in curing my
problem. Since I can’t seem to get any locals in nj to help, I am hoping
someone out there who has a program like Team Viewer would
:35
To: elecraft@mailman.qth.net
Subject: [Elecraft] K3s problem
<<<< My K3s has been working wonderfully since bought new in 2015. I use it
for CW only and run it at 75 - 85 watts. It has a new problem on 15 meters
only. After a short period of transmission the power will disappe
My K3s has been working wonderfully since bought new in 2015. I use it
for CW only and run it at 75 - 85 watts. It has a new problem on 15 meters
only. After a short period of transmission the power will disappear. Turning
the power off and on restores full functions for another amount
Hi Jerry,
First, a couple of questions:
-- does the abrupt loss of power occur if you operate
with the TX PWR set to less than 12 watts on
15 meters? This engages only the low power
driver amplifier and takes the 100 watt PA module
out of the picture.
-- if you're operating on 15 meters at the
My K3s has been working wonderfully since bought new in 2015. I use it for CW
only and run it at 75 - 85 watts. It has a new problem on 15 meters only.
After a short period of transmission the power will disappear. Turning the
power off and on restores full functions for another amount of ti
Perhaps it is still on transmit. A leaky USB-Cable is picking up RF and
hold the PTT.
Just an idea...
Chris, DL2MDU
Am 22.09.2019 um 04:28 schrieb Dave Sublette:
I have had my K3s since January. I use it exclusively on CW. Twice in the
past ten days, in the middle of a QSO, I can hear noth
I have had my K3s since January. I use it exclusively on CW. Twice in the
past ten days, in the middle of a QSO, I can hear nothing when I stop
sending. No background noise. No signal. The quick fix is to turn the
unit off, then right back on.
There is at least an inch of cooling all around t
I contacted Elecraft Support as advised & Doug suggested I re-seat the
filters in the main board & the Sub Receiver.
Lo & behold,... the problem disappeared and audio from all filters is now
normal!
Thanks Doug
73 Ray G3XLG
__
Elecraf
My two narrowest filters have CONFIG -> FLx GN set to 6dB as opposed to
0dB for the others. Press the number keypad to select the appropriate
filter.
Martin, HS0ZED
On 02/04/2019 20:29, Ray Spreadbury via Elecraft wrote:
I have recently fitted a Sub Receiver & some additional filters to my n
Ray,
I doubt that there is anything else wrong. Each filter will vary in its
gain (actually loss) amount. The 4 dB stated in the menu listing for
the 400 and 250 Hz filters is only a starting point.
73,
Don W3FPR
On 4/2/2019 10:36 AM, Ray Spreadbury via Elecraft wrote:
I had done that Don
I had done that Don as per the Manual - 1-2dB for 400Hz & 3-4 dB for the
250Hz filter.
To get the right level of loudness I have had to add the max ie.8 dB. So, is
something else wrong?
Ray G3XLG
__
Elecraft mailing list
Home: http://m
Ray,
You can set the gain parameter (FLxGN) parameter in the menu to
compensate for that. Either use K3 Utility or set it manually in the
CONFIG menu.
73,
Don W3FPR
On 4/2/2019 9:29 AM, Ray Spreadbury via Elecraft wrote:
I have recently fitted a Sub Receiver & some additional filters to my
I have recently fitted a Sub Receiver & some additional filters to my new to
me K3S. I now have in the main RX, a 6K for AM, a 2.8K, 2.1K, 0.4K & 0.25K.
In the sub RX there is a 2.8K, 2.1K, 0.7K, 0.4K & 0.25K. I have a problem
with the 0.4K filter position in both receivers. Between about 0.45 & 0.
Don’t you hate it when the culprit is so simple?
Glad you found it.
Sent from my iPhone
...nr4c. bill
> On Mar 7, 2019, at 10:25 AM, John Stengrevics
> wrote:
>
> Thanks Bill. Yes, that seems to have been the problem.
>
> 73,
>
> John
> WA1EAZ
>
>> On Mar 7, 2019, at 10:24 AM, Nr4c wro
Thanks Bill. Yes, that seems to have been the problem.
73,
John
WA1EAZ
> On Mar 7, 2019, at 10:24 AM, Nr4c wrote:
>
> Check RIT/XIT.
>
> Sent from my iPhone
> ...nr4c. bill
>
>
>> On Mar 6, 2019, at 9:24 PM, John Stengrevics
>> wrote:
>>
>> I have been using my K3S on WSJT-X without an
Check RIT/XIT.
Sent from my iPhone
...nr4c. bill
> On Mar 6, 2019, at 9:24 PM, John Stengrevics wrote:
>
> I have been using my K3S on WSJT-X without any problems. Today, the
> frequency appears to have shifted .7 KHz low. That is, if I were on 50.313
> MHz FT8, I now have to tune to 50.3
I have been using my K3S on WSJT-X without any problems. Today, the frequency
appears to have shifted .7 KHz low. That is, if I were on 50.313 MHz FT8, I
now have to tune to 50.3137 to decode signals.
I would appreciate any suggestions.
Thanks,
John
WA1EAZ
_
20 matches
Mail list logo
