Hi Vic,
Look at the spreadsheet I provide at www.nk7z.net, the CLR SPLIT
function returns the P3 to center use.
--
73's, and thanks,
Dave
For software/hardware reviews see:
http://www.nk7z.net
For MixW support see:
https://groups.yahoo.com/neo/groups/mixw/info
For SSTV help see:
http://groups.y
I see. That will be very useful.
Now all I will need is a save/restore function for the center frequency
and the span. I use fixed mode and have set up those parameters
differently for each band. For example, on 18 MHz I have the center set
to 18.084 and the span to 32 kHz. That gives me a fi
The #RCF+002500 command moves the P3 center frequency to 2.5 kHz above
the K3 VFO A frequency.
It works in both tracking and fixed-tune mode, except that if it places
the VFO cursor off-screen in fixed-tune mode, the P3 may automatically
change its center frequency again to keep it on screen,
It looks like you are setting the span to 6 kHz. Then what exactly does
#RCF +002500 do?
I'm thinking this only works in tracking mode, not fixed mode -- correct?
73,
Vic, 4X6GP/K2VCO
Rehovot, Israel
http://www.qsl.net/k2vco/
On 27 Feb 2016 21:09, Dave Cole wrote:
A new command will be incorp
A new command will be incorporated into the next P3 software release--
RCF.
This new command allows one to move the P3 CENTER frequency around on
the P3 screen, via relative moves, as opposed to the current absolute
moves now available What can this do for you?
In the macro below:
SWT13;SWT
Having the LP-100A on the antenna side is by design. I'm not much
interested in monitoring the antenna VSWR in real time, but I do want to
know the power being delivered at the tail end of the station RF lineup.
The "light show" on the KAT500 and the KPA500 (if it's being used) as
well as the i
I had a similar problem -- even at low power levels, the W2 would
periodically spike a high-SWR and even show 2-3 bars of SWR when no signal
was present. I swapped out the 8-pin cable connecting the sensor to the
W2 and the problem went away. I re-crimped the connectors on the original
Randy,
If your LP100A is on the antenna side of your KAT500 then you are putting your
LP100A in the region of higher SWR if your antenna is not close to resonance.
I think you would want to put your LP100A in the inboard side of the KAT500 so
that you are properly showing the “tuned” SWR on th
I find this thread quite interesting. I too have been dealing with VSWR
"spurts". My TX lineup is similar to Phil's, but I don't have the TX
Monitor. After a recent station rewiring job I found I was having a
great deal of trouble with indicated VSWR jumping to high levels with
the amplifier on
Mike,
Thanks for the comment. I only have one K3 with one P3. My configuration is:
K3/P3 —> KPA500 —> TX Mon Sensor —> LP100A Sensor —> KAT500 —> 80-meter
Dipole
I first noticed the spike with the RED LEDs on both the KAT500 and the KPA500.
I was not looking
at the SWR display on the
Phil:
I have the same setup but only 1 x P3. A K3 and P3 on my left setup
and a K3 on the right setup using a MK2R+ and I noticed what you
mention only once. I was on 80m with
the Right K3 and I saw a brief Power and SWR spike on the Left P3 and
K3. I might have had a bit of SWR on the standal
Does this happy to anyone else with the new TX Monitor…?
My TX monitor sensor sits between my KPA500 and the KAT500 and since I have
installed it and had it up and running I have had more than my average spurts
of high SWR. For example, a key down may cause this spurt but just a moment
later t
If like me you have just upgraded to the latest version 1.50 beta and you
find that the SVGA behaves rather strangely, not remembering settings on
powering off etc., then you might have just sent 'all _new_ firmware' to
the P3 as opposed to sending 'all'.
Don't ask me how I know...
73, Stephen G4
Yeah right... Never going to happen... Hams are without a doubt the
cheapest people I have ever met.
--
Thanks and 73's,
For equipment, and software setups and reviews see:
www.nk7z.net
for MixW support see;
http://groups.yahoo.com/neo/groups/mixw/info
for Dopplergram information see:
http://gr
Have you looked at S Meter Lite Software?
http://www.seed-solutions.com/gregordy/Software/SMeterLite.htm
I've used it with a 2nd CAT port in microHAM Router, which I use with my
microKEYER II.
73, Jim N7US
-Original Message-
Alan,
The only complaint that I have about my K3s is th
It sounds like the EEPROM data got corrupted somehow. Try doing a
Parameter Initialization as described in the P3 Owner's Manual.
Alan N1AL
On Sat, 2012-12-01 at 16:35 -0500, jal2...@aol.com wrote:
> I just put together a new P3 and it isn't seeing the rig. It also will not
> see the computer
I just put together a new P3 and it isn't seeing the rig. It also will not see
the computer through the P3 Utility with the serial cable. If I unplug power
from the P3, I can see the K3 through the same cable using the K3 Utility (same
comport, 4). I am using an Aten usb adapter, but it works f
New P3/SVGA firmware is now available as a general release. This firmware is
currently shipping in all new factory built and kit P3's and SVGA boards.
If you are upgrading from a BETA release, please make sure data terminal
mode and fixed tune are turned OFF before upgrading. You will need ver
Thanks Tom,
73,
P3/SVGA team
--
View this message in context:
http://elecraft.365791.n2.nabble.com/New-P3-Software-and-Firmware-tp7507944p7537006.html
Sent from the Elecraft mailing list archive at Nabble.com.
__
Elecraft mailing lis
YAHO!
Great job Y'All
Amateur Radio Operator N5GE
ARRL Lifetime Member
QCWA Lifetime Member
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:
Great job guys.
73s Jim
JIM ROGERS, W4ATK
w4...@bellsouth.net
http://web.me.com/jimrogers_w4atk
K3/100 P3
K2/10
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Pos
M
> To: Elecraft@mailman.qth.net
> Subject: Re: [Elecraft] New P3 beta firmware
>
> Fred,
> It is a beta version so you will need to download from the P3
> beta ftp site
> ftp://ftp.elecraft.com/P3/firmware/beta/
> Then browse in the P3 utility to where you downloaded
Fred,
It is a beta version so you will need to download from the P3 beta ftp site
ftp://ftp.elecraft.com/P3/firmware/beta/
Then browse in the P3 utility to where you downloaded the zip file
(p3m0105.zip). I have a directory to keep the firmware so I can locate them
easily.
George
AI4VZ
- -
0:42 PM
> To: elecraft@mailman.qth.net; elecraft...@yahoogroups.com
> Subject: [Elecraft] New P3 beta firmware
>
> Beta version 1.05 of P3 firmware is now posted on the
> Elecraft web site.
> This adds some features to enhance the new fixed-tune mode,
> improvements
> in tran
Beta version 1.05 of P3 firmware is now posted on the Elecraft web site.
This adds some features to enhance the new fixed-tune mode, improvements
in transverter operation, more-accurate VFO cursor displays, and several
bug fixes.
One of the bugs was that upgrading between certain versions of firmw
I Love the P3, Bob. And, it will only get much better as the firmware
development continues and new hardware options are introduced. If you are
getting a K3, go for the P3 for sure.
As far as K3 options, it would help a lot in terms of recommendations if you
can be a little more specific about y
If you have the new P3 with the K3, please post some close-up photos of your
gear for all of us to view. Let us know how you like your new P3. What options
would you recommend if buying a factory assembled K3?
Thanks,
Bob Wilderman, K3SRO
_
27 matches
Mail list logo
