On 12/5/2014 11:34 AM, Mark Johnsen wrote:
> I am in the process of working through my Supermax Aniliam Crusader M
> conversion to Mesa 5i25/7i77.
You could re-use the control panel from the Anilam system. It
communicates to the computer via an RS232C interface. The board with the
large DIP chip
On 12/5/2014 12:49 PM, Dave Cole wrote:
> OpenCV is on my watch list as well.
> I just sent out an estimate for a pick and place using a 3 axis gantry
> robot with gripper and rotator along with some other machinery.
> It's PLC driven at the moment. It needs move around 1200 parts to do a
> full
Hi Marius
I f you don't have an aversion to M$, then have a look at Roborealm.com .
It's a very versatile program, and has many interfacing options. You could
run it on a second pc and have a serial link to process commands.
Also, have a look at this camera. Resolution and colour is quite good.
A
On 12/05/2014 03:27 AM, andy pugh wrote:
> It has been reported on the forum that if you have a 2.6 installed
> version of LinuxCNC and also a run-in-place Master version, then even
> after running scripts/rip-environment the "comp" command will invoke
> the 2.6 version, and install into the 2.6 ve
On 12/05/2014 10:26 PM, Gene Heskett wrote:
> Silly Q then. The D525MW board probably has only one usb
> interface, and since my mouse as also plugged into it,
> limiting it to USB1.1 speeds, would I gain video speed by
> sticking a ps2 mouse on the machine, thereby removing the
> speed limitat
Trying to get the spindle running. What should I be seeing on the spin
enable aand direction outputs voltage wise? Not getting anywhere with this
and I see no change in voltage even though it shows them active in Hal.
--
Do
On Sat, 6 Dec 2014, Jeremy Jones wrote:
> Date: Sat, 6 Dec 2014 14:18:40 -0500
> From: Jeremy Jones
> Reply-To: "Enhanced Machine Controller (EMC)"
>
> To: Emc-users@lists.sourceforge.net
> Subject: [Emc-users] 7i76 spindle output
>
> Trying to get the spindle running. What should I be seei
OK got it. Was a little confused there. Guess I was used to wiring up the i
/o's.
On Dec 6, 2014 2:35 PM, "Peter C. Wallace" wrote:
> On Sat, 6 Dec 2014, Jeremy Jones wrote:
>
> > Date: Sat, 6 Dec 2014 14:18:40 -0500
> > From: Jeremy Jones
> > Reply-To: "Enhanced Machine Controller (EMC)"
> >
OK I got it working and I got the speeds calibrated. Any reason why when I
go ccw may speeds are way off? Doubt I will ever go that direction so its
not a big deal but it doesn't make any sense.
On Dec 6, 2014 2:35 PM, "Peter C. Wallace" wrote:
> On Sat, 6 Dec 2014, Jeremy Jones wrote:
>
> > Date
On 6 December 2014 at 21:06, Jeremy Jones wrote:
> Any reason why when I
> go ccw may speeds are way off?
That's normally due to using spindle-speed not spindle-speed-abs.
--
atp
If you can't fix it, you don't own it.
http://www.ifixit.com/Manifesto
I had ABS going and then I switched it over to scale like in the integrator
manual. I can try and switch it back.
On Dec 6, 2014 6:14 PM, "andy pugh" wrote:
> On 6 December 2014 at 21:06, Jeremy Jones wrote:
> > Any reason why when I
> > go ccw may speeds are way off?
>
> That's normally due to
I had this working fine. Changed some stuff around today but nothing
related to my limits. Now every time I home it searches, backs off and
finds the limit but then it shuts down because I'm on a limit switch.
Thoughts?
Also have to switch back to acmxis from gmoccapy to invoke the limit
override
On 12/06/2014 08:55 PM, Jeremy Jones wrote:
> I had this working fine. Changed some stuff around today but nothing
> related to my limits. Now every time I home it searches, backs off and
> finds the limit but then it shuts down because I'm on a limit switch.
> Thoughts?
>
>
In the [AXIS_x] section
Its been set to yes, ignore limits, on all axis since the beginning.
Checked that first. Not sure what has changed and its on all 3 axis now.
Well except z actually. Just x and y.
On Dec 6, 2014 11:17 PM, "Jon Elson" wrote:
> On 12/06/2014 08:55 PM, Jeremy Jones wrote:
> > I had this working fine
Maybe a restart will do it.
On Dec 7, 2014 12:44 AM, "Jeremy Jones" wrote:
> Its been set to yes, ignore limits, on all axis since the beginning.
> Checked that first. Not sure what has changed and its on all 3 axis now.
> Well except z actually. Just x and y.
> On Dec 6, 2014 11:17 PM, "Jon Elso
15 matches
Mail list logo
