Re: [Emc-users] Intel Xeon, Real time performance

On 11/10/2015 1:10 PM, Karlsson & Wang wrote: > Old servers with intel Xeon are often for sale rather cheap, have anyone > tested how they perform in the latency test? Don't buy or accept a free server that doesn't have its drive trays. Every manufacturer uses different trays and usually changes

Re: [Emc-users] Fw: new message

On 11/11/15 00:55, andy pugh wrote: > I don't think it is actually either of us: This spam has been appearing on many lists and they have obviously got a mechanism to create an address book of 'valid' aliases with which to 'dive-bomb' each list :( Until such time as ISP's properly block email traf

Re: [Emc-users] Tool changer finally working on our mill project

Proportionally controlled hydraulic motor, with hard stops and limit switches at each stopping point of its travels. It takes about 2.5 seconds to make the 180 degree rotation. That is about as fast as I can get it to go, without having the tool shaking/rocking too badly when it stops to be exch

Re: [Emc-users] Tool changer finally working on our mill project

I guess that depends on how fast it rotates and how the tool is gripped. It also depends on whether the rotation is a DC motor with end stop switches or a servo with position reporting. No point in moving and decelerating to a stop, telling the unit to extend and then accelerating back up to the

[Emc-users] [SPAM] Fw: new message

Hey! New message, please read Christie Nichols -- ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforg

Re: [Emc-users] Fw: new message

On 11 November 2015 at 00:48, Gene Heskett wrote: > your, or Jack Coats, has an infected machine. I don't think it is actually either of us: Received: from catv-89-132-168-228.catv.broadband.hu ([89.132.168.228] It just has my name (or Jeff's name) and Jack's email address. -- atp If you can

Re: [Emc-users] Would this new item be of any use?

On Tuesday 10 November 2015 18:58:01 Bruce Layne wrote: > The resolution is determined by the number of teeth on the gear that > is being sensed by the two Hall effect sensors in that integrated > Honeywell sensor. For example, if you had a 100 tooth gear, you'd > have 400 quadrature state change

[Emc-users] [SPAM] Fw: new message

Hey! New message, please read Christie Nichols -- ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforg

[Emc-users] Fw: new message

Hey! New message, please read Christie Nichols -- ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sour

[Emc-users] [SPAM] Fw: new message

Hey! New message, please read Christie Nichols -- ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge

[Emc-users] [SPAM] Fw: new message

Hey! New message, please read Christie Nichols -- ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.source

[Emc-users] [SPAM] Fw: new message

Hey! New message, please read Christie Nichols -- ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.ne

[Emc-users] [SPAM] Fw: new message

Hey! New message, please read Christie Nichols -- ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.

Re: [Emc-users] Fw: new message

On Tuesday 10 November 2015 18:44:49 andy pugh wrote: your, or Jack Coats, has an infected machine. > Hey! > > > > New message, please read > > > > andy pugh > > -- >

Re: [Emc-users] Need a better wm/Gui for my machines

On Tuesday 10 November 2015 14:53:07 Dr. Nikolaus Klepp wrote: > Hi Gene! > > LOL ... I think the rinity mailinglist has an archive :-) > > Place this in your .bashrc if you run linuxcnc from commandline (all > in one line): > > alias linuxcnc="xrdb -all -query|sed -e 's#[A-Z_]*BACKGROUND# gray90#

[Emc-users] [SPAM] Fw: new message

Hey! New message, please read Smooth-On Inc. -- ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge

[Emc-users] [SPAM] Fw: new message

Hey! New message, please read Jeff Epler -- ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourcefor

[Emc-users] [SPAM] Fw: new message

Hey! New message, please read Jeff Epler -- ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net

[Emc-users] [SPAM] Fw: new message

Hey! New message, please read Jeff Epler -- ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.

[Emc-users] [SPAM] Fw: new message

Hey! New message, please read Trey Cox -- ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/list

[Emc-users] [SPAM] Fw: new message

Hey! New message, please read Jeff Epler -- ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourc

[Emc-users] [SPAM] Fw: new message

Hey! New message, please read j...@coats.org -- ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge

[Emc-users] Fw: new message

Hey! New message, please read andy pugh -- ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge

[Emc-users] Fw: new message

Hey! New message, please read andy pugh -- ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourcefo

[Emc-users] Fw: new message

Hey! New message, please read andy pugh -- ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.n

Re: [Emc-users] Would this new item be of any use?

The resolution is determined by the number of teeth on the gear that is being sensed by the two Hall effect sensors in that integrated Honeywell sensor. For example, if you had a 100 tooth gear, you'd have 400 quadrature state changes per revolution. A spindle speed sensor doesn't really need

Re: [Emc-users] Intel Xeon, Real time performance

25k? Should it be 25µ? I tried POS terminals, they have touch screen but delay is not good. > On 10 November 2015 at 20:10, Karlsson & Wang > wrote: > > Old servers with intel Xeon are often for sale rather cheap, have anyone > > tested how they perform in the latency test? > > I have a first

Re: [Emc-users] Would this new item be of any use?

On Tuesday 10 November 2015 14:07:34 andy pugh wrote: > On 10 November 2015 at 18:53, Greg Bentzinger wrote: > > Got an advert for this since I am an Allied customer and was > > wondering if this would be useful as a spindle sensor. > > > > http://www.alliedelec.com/lp/151110/honeywell/?utm_sour

Re: [Emc-users] Would this new item be of any use?

On Tuesday 10 November 2015 13:53:55 Greg Bentzinger wrote: > Got an advert for this since I am an Allied customer and was wondering > if this would be useful as a spindle sensor. > > http://www.alliedelec.com/lp/151110/honeywell/?utm_source=prod&utm_med >ium=email&utm_campaign=151110_product > Ce

Re: [Emc-users] Intel Xeon, Real time performance

On 10 November 2015 at 20:10, Karlsson & Wang wrote: > Old servers with intel Xeon are often for sale rather cheap, have anyone > tested how they perform in the latency test? I have a first-generation dual Xeon server as my lathe controller. I seem to recall that it was about 25k latency when I

Re: [Emc-users] Tool changer finally working on our mill project

You may need to have it retracted to clear another tool in an adjacent pocket in the turret. What if you put a large diameter tool, like a face mill, beside another? On Tue, Nov 10, 2015 at 4:54 PM, Dave Cole wrote: > If you rotate it with it extended it will have a lot more inertia, tend > to

Re: [Emc-users] Tool changer finally working on our mill project

If you rotate it with it extended it will have a lot more inertia, tend to throw the tool, and be harder on the rotator. If it was rotated with the tool retracted originally, there is likely a good reason why they did that. Dave On 11/10/2015 4:36 PM, r...@superiorroll.com wrote: > When I was

Re: [Emc-users] Tool changer finally working on our mill project

Good Day Top job really looks the part. Has the same shift pattern as my Matsuura MV 100V. Cheers john > Date: Tue, 10 Nov 2015 13:00:03 -0500 > From: petefro...@gmail.com > To: emc-users@lists.sourceforge.net > Subject: Re: [Emc-users] Tool changer finally working on our mill project > > Ver

Re: [Emc-users] Tool changer finally working on our mill project

When I was writing the ladder logic I followed the original sequence of events, but this does make sense, guess I've got some tweaking to do. Thanks Rick Original Message Subject: Re: [Emc-users] Tool changer finally working on our mill project From: "Pete Matos" Date: Tu

Re: [Emc-users] Tool changer finally working on our mill project

John I wondered the same thing but chalked it up to clearing the housing of the carousel...altho it does appear to have room. Pete On Tue, Nov 10, 2015 at 3:22 PM, John Dammeyer wrote: > Hi, > Any reason why you won't push the tool holder outwards once it clears the > carousel so that when it

Re: [Emc-users] Would this new item be of any use?

I too got that advertisement. If your spindle has a suitably fine gear on it I think it would work fine. You'd still need to add a second sensor for an index position in order to either thread or position the spindle for a toolchanger. John > -Original Message- > From: Greg Bentzinger [m

Re: [Emc-users] Tool changer finally working on our mill project

Hi, Any reason why you won't push the tool holder outwards once it clears the carousel so that when it arrives under the spindle it's already fully extended? Would save time on tool changes. Very nice though. John > -Original Message- > From: Pete Matos [mailto:petefro...@gmail.com] > Sen

[Emc-users] Intel Xeon, Real time performance

Old servers with intel Xeon are often for sale rather cheap, have anyone tested how they perform in the latency test? Nicklas Karlsson -- ___ Emc-users mailing list Emc-users@l

Re: [Emc-users] Need a better wm/Gui for my machines

Hi Gene! LOL ... I think the rinity mailinglist has an archive :-) Place this in your .bashrc if you run linuxcnc from commandline (all in one line): alias linuxcnc="xrdb -all -query|sed -e 's#[A-Z_]*BACKGROUND# gray90#' -e 's#[A-Z_]*FOREGROUND# Black#' -e 's#[A-Z_]*HIGHLIGHT# White#' -e 's#

Re: [Emc-users] Need a better wm/Gui for my machines

On Tuesday 10 November 2015 08:55:30 Dr. Nikolaus Klepp wrote: > Am Dienstag, 10. November 2015 schrieb Gene Heskett: > > On Tuesday 10 November 2015 07:34:46 Dr. Nikolaus Klepp wrote: > > > Am Dienstag, 10. November 2015 schrieb Gene Heskett: > > > > Good morning everybody; > > > > > > > > I am r

Re: [Emc-users] Would this new item be of any use?

On 10 November 2015 at 18:53, Greg Bentzinger wrote: > Got an advert for this since I am an Allied customer and was wondering if > this would be useful as a spindle sensor. > > http://www.alliedelec.com/lp/151110/honeywell/?utm_source=prod&utm_medium=email&utm_campaign=151110_product It looks pe

[Emc-users] Would this new item be of any use?

Got an advert for this since I am an Allied customer and was wondering if this would be useful as a spindle sensor. http://www.alliedelec.com/lp/151110/honeywell/?utm_source=prod&utm_medium=email&utm_campaign=151110_product

Re: [Emc-users] Tool changer finally working on our mill project

Very nice Rickcolor me jealous!! Pete On Tue, Nov 10, 2015 at 12:37 PM, Rick Lair wrote: > Here it is, after putting all the pieces together, and working the bugs > out, I finally got the tool change working using Andy Pugh's carousel > component to control the tool carousel, and a pretty h

[Emc-users] Tool changer finally working on our mill project

Here it is, after putting all the pieces together, and working the bugs out, I finally got the tool change working using Andy Pugh's carousel component to control the tool carousel, and a pretty healthy chunk of ladder logic to control everything else. All using Linuxcnc 2.7. Thanks for the hel

Re: [Emc-users] Need a better wm/Gui for my machines

On Tuesday 10 November 2015 08:55:30 Dr. Nikolaus Klepp wrote: > Am Dienstag, 10. November 2015 schrieb Gene Heskett: > > On Tuesday 10 November 2015 07:34:46 Dr. Nikolaus Klepp wrote: > > > Am Dienstag, 10. November 2015 schrieb Gene Heskett: > > > > Good morning everybody; > > > > > > > > I am r

Re: [Emc-users] Need a better wm/Gui for my machines

Am Dienstag, 10. November 2015 schrieb Gene Heskett: > On Tuesday 10 November 2015 07:34:46 Dr. Nikolaus Klepp wrote: > > > Am Dienstag, 10. November 2015 schrieb Gene Heskett: > > > Good morning everybody; > > > > > > I am running TDE on this box, and am quite happy with it. > > > > > > [...] > >

Re: [Emc-users] Need a better wm/Gui for my machines

On Tuesday 10 November 2015 07:34:46 Dr. Nikolaus Klepp wrote: > Am Dienstag, 10. November 2015 schrieb Gene Heskett: > > Good morning everybody; > > > > I am running TDE on this box, and am quite happy with it. > > > > [...] > > > > So on your machines with limited horsepower like the atoms, what

Re: [Emc-users] Need a better wm/Gui for my machines

On Tuesday 10 November 2015 07:34:46 Dr. Nikolaus Klepp wrote: > Am Dienstag, 10. November 2015 schrieb Gene Heskett: > > Good morning everybody; > > > > I am running TDE on this box, and am quite happy with it. > > > > [...] > > > > So on your machines with limited horsepower like the atoms, what

Re: [Emc-users] Need a better wm/Gui for my machines

Am Dienstag, 10. November 2015 schrieb Gene Heskett: > Good morning everybody; > > I am running TDE on this box, and am quite happy with it. > > [...] > > So on your machines with limited horsepower like the atoms, what wm/gui > family are you folks using? Hi Gene! As you might suspect, I'm ru

[Emc-users] Need a better wm/Gui for my machines

Good morning everybody; I am running TDE on this box, and am quite happy with it. The wm, I think its xfce, on the real machines, suffers from a utility for this, and a utility for that, that winds up having poor control of screen usage, tieing up two vertical spaces for all its buttons, none o

Re: [Emc-users] could Linux cnc control of unconventional ... hydraulic

On 11/9/2015 1:26 PM, Roland Jollivet wrote: > I don't see why it has be this way. Running a pump at full power past a > valve sounds daft. That's why the new pressbrakes, presses and injection > moulding machines use servo hydraulics. > > Simply put, you have a gear pump, and both ends go to a cyl