Re: [Emc-users] rt_preempt 4.4.0 on jessie

On Wednesday 24 February 2016 13:38:16 sam sokolik wrote: > Seb put up some 686/amd64 -rt kernels. I threw it on a HP 8100 work > station. (2nd gen i5 with onboard intel graphics) > > deb http://highlab.com/~seb/linuxcnc jessie main > > It is pretty impressive. > Darn, I'm still on wheezy on

Re: [Emc-users] Information for spindle and drive Kollmorgen Ind

Thank you for the information. But I have some basic machines that work with linuxcnc. No problems. Today my machining center out of use I have in process an order. With linuxcnc I am independent Pierre finemeca.be 2016-02-24 19:42 GMT+01:00 Jeff Johnson : >

Re: [Emc-users] Seeks electrical schematics Cincinnati Milacron Arrow 750

ok thank you 2016-02-24 19:59 GMT+01:00 Stuart Stevenson : > yes > > On Wed, Feb 24, 2016 at 12:21 PM, Forum Deswysen > > wrote: > > > Hello Stuart, > > > > Thank you for the information. > > > > It is this site ??? > > http://www.fivesgroup.com/ >

Re: [Emc-users] Information for spindle and drive Kollmorgen Ind

** Hello, We have a machining center Cincinnati Milacron Arrow 750. The control of the machine is out of service and we will change it. I am searching information on the spindle motor and drive: High performance induction motor Model: 1-604-0006 Serie: 98F286-77 27A 3.7 KW

[Emc-users] rt_preempt 4.4.0 on jessie

Seb put up some 686/amd64 -rt kernels. I threw it on a HP 8100 work station. (2nd gen i5 with onboard intel graphics) deb http://highlab.com/~seb/linuxcnc jessie main It is pretty impressive. Onboard graphics run overnight http://imgur.com/fMuKwSP I installed a ati pci-e graphics card for

[Emc-users] Information for spindle and drive Kollmorgen Ind or Cincinnati

Hello, We have a machining center Cincinnati Milacron Arrow 750. The control of the machine is out of service and we will change it. I am searching information on the spindle motor and drive: High performance induction motor Model: 1-604-0006 Serie: 98F286-77 27A 3.7 KW Kollmorgen Ind or

Re: [Emc-users] Seeks electrical schematics Cincinnati Milacron Arrow 750

Hello Stuart, Thank you for the information. It is this site ??? http://www.fivesgroup.com/ Best regards Pierre 2016-02-22 21:37 GMT+01:00 Stuart Stevenson : > I realize you want the schematics as cheap as possible. I hope someone has > a set to give you. I would think you

[Emc-users] Need some math help

Greetings all; That code snippet I posted to the devel list, could use some help. These parts are nominally 2.05" wide, and I normally locate them in the vise so they are resting against a small bit of wood held across the end of the jaw opening as I clamp them up in the vise. However,

[Emc-users] One learns things by reading the docs

Greetings all; Skimming thru the doc pdf, under functions on page 204, I see there is an EXISTS[#] function that I propose to make use of. The one big file that carves the ends of all 4 major board parts of the blanket chest, uses just 2 variables at the top of the file to control which of

Re: [Emc-users] debian locks on boot

Your APU and chipset should work just fine with Debian and they already have. I'd try a fresh install and see if it works again. Then maybe run memtest for a few hours. It could be flaky hardware but I'd reformat and reinstall to rule out software being the problem first. Pay attention to any

Re: [Emc-users] debian locks on boot

On Wed, Feb 24, 2016 at 7:45 AM, Jim Craig wrote: > > Anyway about the computer > > CPU AMD E-450 APU with Radeon HD Graphics 1650 MHz > 4gb RAM > that's interesting, I have an AMD E350 that I just installed 32 bit Ubuntu 14.04 on and it runs fine so far. My

Re: [Emc-users] debian locks on boot

On 2/23/2016 10:21 PM, Jon Elson wrote: > On 02/23/2016 08:38 PM, Jim Craig wrote: >> I installed the iso image from 2.6.8 on my dads laptop. I had everything >> working the way I wanted it last night. I powered it down and then >> tonight when It boots up the system will lock up within 10 to 15