I got this error but this configuration was working before and I made
no changes. Can you help me?
~$ linuxcnc ~/linuxcnc/configs/sim.qtpyvcp/xyzab.ini
LINUXCNC - 2.9.0-pre0-4771-ged1f4ddf7
Machine configuration directory is
'/home/sel/linuxcnc/configs/sim.qtpyvcp'
Machine configuration file is '
Did you recently pull master?
You are using python 2.7 which isn’t supported in master anymore.
The updating documentation has steps required to change the configuration for
python related things.
> On 26. Jan 2022, at 16:03, Valerio Bellizzomi wrote:
>
> I got this error but this configuratio
Inductosyn has a major cost advantage over Accupins. It is a copper film bonded
to a steel backplate. It is a photo etch process like a circuit board.
The slider is the same process with a thin foil protection over it. The slider
provides sine and cosine, and the scale reads displacement. They
Which documentation?
thanks
On Wed, 2022-01-26 at 16:16 +0100, Rene Hopf via Emc-users wrote:
> Did you recently pull master?
> You are using python 2.7 which isn’t supported in master anymore.
> The updating documentation has steps required to change the
> configuration for python related thing
> On 26. Jan 2022, at 16:35, Valerio Bellizzomi wrote:
>
> Which documentation?
https://linuxcnc.org/docs/devel/html/getting-started/updating-linuxcnc.html#_python3_and_gtk3
>
> thanks
>
>
>> On Wed, 2022-01-26 at 16:16 +0100, Rene Hopf via Emc-users wrote:
>> Did you recently pull master
On Wed, 2022-01-26 at 16:42 +0100, Rene Hopf via Emc-users wrote:
> > On 26. Jan 2022, at 16:35, Valerio Bellizzomi
> > wrote:
> >
> > Which documentation?
>
> https://linuxcnc.org/docs/devel/html/getting-started/updating-linuxcnc.html#_python3_and_gtk3
thank you but this procedure did not wor
In the documentation for BSPI at
http://linuxcnc.org/docs/2.8/html/man/man9/hostmot2.9.html#BSPI there is a
reference to some man pages like man mesa_7i65, which prints the man page
when I issue the command for it,
But the documentation also refers to some other man pages for the the
following: man
On Wed, 26 Jan 2022 at 23:36, John Figie wrote:
> *1) what must I do to see these bspi man pages?*
Wel, they _should_ show up here at the bottom under "Hostmot2 API Calls"
https://linuxcnc.org/docs/2.8/html/
But they don't. Oddly.
They do appear in the old docs.
https://linuxcnc.org/docs/2.7/htm
On Wed, 26 Jan 2022 at 23:36, John Figie wrote:
> *3) in the 7i65 component there are some lines that refer to RTAPI but in
> my case I am planning on using the PREEMPT RT enabled kernel. Does the
> component work with either?*
The RTAPI is a wrapper that supplies a uniform interface (API) for a
I had some problems today with a small XL timing
pulley slipping on a NEMA17 stepper shaft due to
the set screw loosening after running for long
periods (multiple days). I drilled and tapped a
second set screw hole, and I can probably apply
some thread locker, but I got to wondering if it
would be
I assume everyone knows about these.
https://www.fennerdrives.com/trantorque/
Not cheap but tend to work.
Dave
On 1/26/22 8:30 PM, Ralph Stirling wrote:
I had some problems today with a small XL timing
pulley slipping on a NEMA17 stepper shaft due to
the set screw loosening after running for l
Take a grinder to the motor shaft and make a flat on it. Then tighten the
setscrew on the flat with some Loctite on the threads or a second setscrew
behind it if you have the room.
John
> -Original Message-
> From: Ralph Stirling [mailto:ralph.stirl...@wallawalla.edu]
> Sent: January-
On Thursday, January 27, 2022 12:45:22 AM EST dave engvall wrote:
> I assume everyone knows about these.
> https://www.fennerdrives.com/trantorque/
> Not cheap but tend to work.
>
> Dave
>
> On 1/26/22 8:30 PM, Ralph Stirling wrote:
> > I had some problems today with a small XL timing
> > pulley
13 matches
Mail list logo