Re: [Emc-users] Lost fractions of a step

I suspect that if you were indeed to cut each tooth completely and sequentially you could get the spiral wave of material heat extending that would cause even stranger errors! In the effort to cut a little of each I would use the Fibonacci number applied to 360degrees - as I remember aprox. 137 de

Re: [Emc-users] NASA's 3D Printer

orations, FREE > > http://pubads.g.doubleclick.net/gampad/clk?id=157005751&iu=/4140/ostg.clktrk > ___ > Emc-users mailing list > Emc-users@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/emc-users > -- Tobias Gogolin Tel. D1 (49) 0151 5187 5210 Tel.

[Emc-users] Delta 3D printer with servo drive?

am suggesting small geared brushless motors, so I am hoping for an expert opion, and also groups, an wikis where maybe lists of the available motion controllers are offered? Thanks! Tobias Gogolin -- Download BIRT iHub F

Re: [Emc-users] Delta 3D printer with servo drive?

on done between linear delta motion control and Euclidean G-code, or is non Euclidean G-Code used? Thanks again for all the participation, and happy weekend! cheers Tobias! On Sat, Feb 21, 2015 at 2:44 PM, Viesturs Lācis wrote: > 2015-02-21 15:16 GMT+02:00 Tobias Gogolin : > > I am

[Emc-users] Questions about your Stepper kit

Hello EMC users, I am new to this issue (have been lurking for a while) but now plunged into the reality of having to (or wanting to) implement a EMC based system, as the Torchmate Plasma Stepper Controller we had was stolen by unqualified hand... I am wondering if this type of kit will work with

Re: [Emc-users] Questions about your Stepper kit

Regards > Roland > > > > On 31 July 2011 08:32, Tobias Gogolin wrote: > > > Hello EMC users, I am new to this issue (have been lurking for a while) > but > > now plunged into the reality of having to (or wanting to) implement a EMC > > based system, as the Torchm

Re: [Emc-users] Questions about your Stepper kit

r implemented a closed loop stepper controller in EMC? Thanks guys! On Tue, Aug 9, 2011 at 12:11 AM, gene heskett wrote: > On Tuesday, August 09, 2011 02:33:30 AM Tobias Gogolin did opine: > > > Thanks cogoman and Roland for replying, yes indeed that is a quite > > importan

Re: [Emc-users] Questions about your Stepper kit

Ok, maybe I should go directly to Nema 23 Servos, any recomendations for affordable units? Or actually I could adapt a different size too if that be found more appropriate! On Tue, Aug 9, 2011 at 10:53 AM, Peter C. Wallace wrote: > On Tue, 9 Aug 2011, Tobias Gogolin wrote: > > >

Re: [Emc-users] Questions about your Stepper kit

Thanks Andy, these keling servos are sweet, how do I drive them? And while your at it might you recommend some power supply? On Tue, Aug 9, 2011 at 2:56 PM, andy pugh wrote: > On 9 August 2011 19:32, Tobias Gogolin wrote: > > Ok, maybe I should go directly to Nema 23 Se

Re: [Emc-users] Questions about your Stepper kit

their application engineering? On Wed, Aug 10, 2011 at 2:28 AM, andy pugh wrote: > On 10 August 2011 07:52, Tobias Gogolin wrote: > > Thanks Andy, these keling servos are sweet, how do I drive them? > > Which ones are you looking at? Brushed or Brushless? > > How do yo

Re: [Emc-users] Questions about your Stepper kit

this week! On Wed, Aug 10, 2011 at 1:28 PM, Kirk Wallace wrote: > On Wed, 2011-08-10 at 12:25 -0700, Tobias Gogolin wrote: > > No problem if the servo solution is a bit more expensive than the > steppers, > > i do believe that i's the way to go for a more agile and useful

Re: [Emc-users] Questions about your Stepper kit

> _______ > Emc-users mailing list > Emc-users@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/emc-users > -- Tobias Gogolin Tel. Movistar (646) 124 32 82 Tel. Telcel (646) 160 58 99 skype: moontogo messenger: usert..