Re: [Flexradio] !.12.0 Digital modes and receive image on the SDR1000

Ross, Did you create a new database for v1.12.0 and are you using that one for the tests you are running? If you are, did you modify the database with the Database Migration tool? -Tim -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Ross Sent:

[Flexradio] 2nd receiver and ATU install

Hello I will receive my 2nd receiver board today but the ATU I ordered is on back order. Would it make the install easer to wait until the ATU arrives and install both at the same time. Thanks: Randy Pence N4JZY ___ FlexRadio Systems Mailing List

Re: [Flexradio] 2nd receiver and ATU install

The ATU mounts on top of the PA board (on top of the heat sink) and the RX2 mounts on the other side (bottom) of the heatsink on top of the TRX board. If you install the RX2 now, you will not have to remove it to install the ATU. I don't think it will make it any easier to wait, but it would

[Flexradio] Just asking

Before I hit the Flex bug and request boards, I have a question. Can the RX2 audio be split away from the RX1 audio and brought out separately, like to a new pair of VAC's, or to the LINE OUT on the back of the radio? Apparently, RX2's audio does not show up on the VAC when choosing VAC1 for

Re: [Flexradio] Just asking

Dave, You have lots of questions. Please see my comments below -Tim -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Dave Blaschke Sent: Friday, June 13, 2008 10:05 AM To: flexradio@flex-radio.biz Subject: [Flexradio] Just asking Before I hit the

Re: [Flexradio] Just asking

Dave, The best way to do that at the moment is to use the pan sliders. Put rx1 all the way to the left, and rx2 to the right. Then you need to route the audio back into the computer. This can be done from the power speaker out. Perhaps a bit inconvenient, but this approach does have lower

[Flexradio] Binder Clip in Radio

Hello I heard something rattling around in the radio while preparing to remove the top cover for 2nd receiver install. When I took the cover off I found a binder clip laying on the circuit board. Both of the silver arms that go on each side were missing. It would not be so bad but I can not use

Re: [Flexradio] Binder Clip in Radio

Darn it, I want a non-functional binder clip inside my SDR-1000! You 5000 guys get all the good stuff ;) Pete, N3EVL -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] radio.biz] On Behalf Of Randy Pence Sent: Friday, June 13, 2008 1:20 PM To:

Re: [Flexradio] Binder Clip in Radio

Actually, the clip has a function, but it is top secret high tech innovation. -Tim -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of [EMAIL PROTECTED] Sent: Friday, June 13, 2008 2:48 PM To: [EMAIL PROTECTED]; flexradio@flex-radio.biz Subject: Re:

Re: [Flexradio] Binder Clip in Radio

Tim Ellison wrote: Actually, the clip has a function, but it is top secret high tech innovation. Yet another hardware development outside of the 'Software' only ideal... ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz

Re: [Flexradio] FlexRadio Digest, Vol 38, Issue 13

Hi Folks New Release! Ross stated some differences between former versions. I am seeing the same. I have several different versions installed for my SDR1000's. So I can quick switch between them. Using the same computer soundcard, SDR settings, setup etc. So far all showed the same s/n and

Re: [Flexradio] FlexRadio Digest, Vol 38, Issue 13

I submitted a bug report on this one. The scaling on the panadapter is off by ~20 dbm from the S-meter. S-meter is right on with my Elecraft XG-1 signal source. Carl WC0V Chris Gerber wrote: Hi Folks New Release! Ross stated some differences between former versions. I am seeing the same.

Re: [Flexradio] FlexRadio Digest, Vol 38, Issue 13

Another thing I'm noticing in V1.12.0 is when I see a detected signal in the pan adapter, I'm also seeing a mirror image of the same signal either up or down frequency by about 10KHz. When tuning to these signals they sometimes merge but not always. Sometimes they can be detected at different

[Flexradio] marketing incentive

Flex should include a packet of this stuff to brush on our coax and antennas with each RX2 board sold. http://www.solarflux.com/Pages/Productinfo.html BTW: The RX2 instructions say: T-20 Torx driver (included with the radio) I sure didn't get onefortunately I have a couple of Torx Sets,

[Flexradio] got my RX2 installed

and it worked on the first try. Well actually it didn't, I still had to set it up Right now I have rx1 listening to 6 and rx2 listening to 20 digital Learning curve I'd like to have rx2 decode the rtty via WinWarbler. So far haven't figured out how to do that.

[Flexradio] bug reports for RX2

When I try to enter a bug report I get the following message: Server Error in '/' Application Using themed css files requires a header control on the page. (e.g. head runat=server /). Anyone know what this is? Dave, W5UN ___ FlexRadio Systems

Re: [Flexradio] Binder Clip in Radio

How soon will the BC-1 upgrade be available for the SDR-1000? David Ackrill wrote: Tim Ellison wrote: Actually, the clip has a function, but it is top secret high tech innovation. Yet another hardware development outside of the 'Software' only ideal...

Re: [Flexradio] !.12.0 Digital modes and receive image on the SDR1000

Ross, Also did you re-run all the calibrations? Including frequency, rx image, tx image, and PA. 73, Dudley WA5QPZ Tim Ellison wrote: Ross, Did you create a new database for v1.12.0 and are you using that one for the tests you are running? If you are, did you modify the database with

[Flexradio] 2008/June/14 FRF TeamSpeak audio

The 14/June Flex Radio Friends TeamSpeak zipped mp3 (1 hour 12 minutes) plus a text file of channel comments is available at: http://www.hamsdr.com/dnld.aspx?id=829 or http://www.hamsdr.com/dnld.aspx Mike - AA8K ___ FlexRadio Systems

Re: [Flexradio] Panadapter Settings

You might check the Display Tab in Setup.. Try changing the Align from Auto. 73, Dudley WA5QPZ Chris Gerber wrote: Hi Folks New Release! Ross stated some differences between former versions. I am seeing the same. I have several different versions installed for my SDR1000's. So I can

[Flexradio] SDR1000 Edirol FA66 - echo on transmit

Hi All I seem to be experiencing on transmit what sounds like an echo its sounds like a delay i.e. a few milliseconds at first i thought it was RF getting in..but on air reports say its an echo. I have tried on current Test SVN as well as K6JCA consoles and

[Flexradio] SDR-1000 frequency error.

All of a sudden, WWV shows up at ~2.511, 5.022, 10.044 MHZ. tried deleting the database and wisdom. restarted 1.12 and same thing. Can not calibrate frequency. Using ver 1.10.4, DDS Offset was 3125. dds offset has been reset to zero. Using ver 1.10.4, DDS Offset was 3125. changing it makes no

Re: [Flexradio] bug reports for RX2

Dave, I see that you did enter a bug report. Is this still an issue? At what point in the process do you see this? When you receive the error message, what is in the URL line of your browser? The line that should be there when entering a new bug report should be the following: