Brian,
wow - thanks for the step-by-step instructions below! I check against
your list and the only thing I do different for the base setup is to
go straight to WinXP Pro SP3 (as that's what I have as an install disk
here).
73, Frank DG1SBG
Am 14.06.2009 um 19:39 schrieb Brian Lloyd:
On
Hi Tim,
well, as I said: The F-5kA *is* showing up in the driver control panel
and the driver does not complain about not finding the device.
So, in my state of reasoning and cause analysis, I'd rule out the
FireWire low-level and driver level interfaces/connections/software.
Would you ag
Neal,
yes, the radio does show up as a sound card. OS is WinXP Pro SP 3 with
KB955408 installed.
73, Frank DG1SBG
Am 14.06.2009 um 13:52 schrieb Neal Campbell:
In the control panel does the radio show up as a sound card? What
operating system are you using?
73
Neal Campbell
Abroham Neal S
Conditions were rather spotty on 6m down in the Southwest, but enough
openings to keep it interesting.
The F3K performed magnificently! Even though I was using the compressor,
I had several unsolicited comments on the good quality of the audio, and
it seemed to punch through the pileups just fin
Hi Tom,
Are talking about using your 5000 on 6M in the ARRL June VHF contest this
last weekend? If so ,the 5000 needs an external preamp connected to the RX1
In/Out ports to get the best possible performance out of your 5000 on that
band. The 6M noise figure is pretty high without one, but on
I tried to use the line in audio input of the FLEX-5000A today with the VOX
button enabled. I was surprised VOX would not work with that input selected.
Is that the intended operation?
I checked the manual and didn't see anything to indicate that VOX only works
using the front panel microphone
Tom,
Glad that you are enjoying the radio..When you say that the receiver
is hard of hearing, if you are going by the S-meter, it is very
accurately verses some other receivers (like the IC706) where the S
meters can be as much as 20 db off on the high side. I think that once
you get
I the box thru the paces over the weekend, the ease of operation and the
panadptor make it a winer. The receiver is a little hard of hearing, but the
audio processing made ther difference.
I had some high Q rates on sat and still was able to pick some off using the
second receive.
Nothing but g
Tim,
Using PWR SDR 1.18.0, 5KA, and Apple iMAC w/XP PRO - nothing I would
describe as a whine or anything unusual for that matter. Checked with
and w/o headphones, on antenna and on dummy load. Just the usual trash
(40 kHz spacing) from the switching power supply when connected to
the an
No unusual noises or whines here either.
-Tim
-Original Message-
From: flexradio-boun...@flex-radio.biz
[mailto:flexradio-boun...@flex-radio.biz] On Behalf Of N4PY2
Sent: Sunday, June 14, 2009 10:09 PM
To: flexra...@flex-radio. Biz
Subject: [SPAM] Re: [Flexradio] Low level whine Flex
I don't hear any low level whine on my F5K at those frequencies.
Carl Moreschi N4PY
121 Little Bell Drive
Bell Mountain
Hays, NC 28635
- Original Message -
From: "NZ8J"
To: "flexra...@flex-radio. Biz"
Sent: Sunday, June 14, 2009 9:41 PM
Subject: [Flexradio] Low level whine Flex 5K
Hi,
I just noticed today on all versions of SDR that on 30 meters (the only
band I've noticed it so far) , there is a distinct low level whine
between the frequencies of 10.109.769 and 10.102.139. Tuning through
those freq's the whine will start and stop, however it remains when SDR
is stopped, whe
Glad to help, hope those pics I gave helped.
No matter how much we explain it in wordsscreen shots seem to work
better.
On 6/14/2009 4:07:20 PM, STORMYX (stor...@cableone.net) wrote:
Firebrick...got the 5000 going on everything now, using MixW es 1.18.1.
Works like a champ. Thanks for yo
Firebrick...got the 5000 going on everything now, using MixW es 1.18.1.
Works like a champ. Thanks for your offer to help on the phone.
Of course, having said it's working fine, the next time I turn it on, with
my luck it won't. Great bunch of people on this reflector, and SMART!!!
7third,
Le
Same exact thing here as WX7Y Bret, the temporary work around is to sequence
through the sample rates. Need to do this every time on start up, a large
change in frequency or band change. Cycle through the sample rates and it
will start operating. I'm sure this will be fixed up very soon. (it
Same exact problem here EXCEPT if I would go and reset my Audio sample rate
to 4800 it started to work except the SQUELCH was up and squelching the
receiver, I then went to 9600 sample rate and every NOW was working then I
went back to 19200 sample rate and it now works BUT when I shut down
PowerS
Frank,
A couple of other things, when you installed the driver, you should
have gotten the New Found HW three times there on XP (Vista doesn't do
that) , then check the Sounds and Audio Device in the Control panel,
then the Audio tab, make sure that you see the Flex 5000 driver in the
Pl
I did the same thing and am experincing the same problem.
Duh
I just entered a bug report.
On 6/14/2009 1:25:28 PM, NZ8J (n...@woh.rr.com) wrote:
I just tried this test branch 1.19.1 SVN:3166 , but had two problems
when I did the calibration for images, 17 and 6 meters failed plus I
don't get an
I am having this exact same problem with Test SVN 3166.
Both receivers. on XP pro and Windows 7 64bit
Tried new database, power cycle, etc.
Trunk, Pretty betty work fine.
Dave W0DHB
NZ8J wrote:
I just tried this test branch 1.19.1 SVN:3166 , but had two problems
when I did the calibration f
I just tried this test branch 1.19.1 SVN:3166 , but had two problems
when I did the calibration for images, 17 and 6 meters failed plus I
don't get any audio and the panadapter line jumps from a normal signal
line at about -120 or so up to a straight line at about -60. It seems to
happen about ever
Uninstall Windows Desltop Search. Reboot. Install Google Desktop.
Reboot. Log in. Go away for a day.
Come back and have fun after Google Desktop is finished indexing. It
will put itself to sleep while you are working so you need to leave your
computer alone for the indexing job to get do
On Sun, Jun 14, 2009 at 5:54 AM, Tim Ellison wrote:
> Ah ha!
>
> I have had less than stealer success using Firewire 800 cards (either 800
> with a bilingual cable or a 800/400 combo card) with the FLEX-5000 and
> FLEX-3000. I tried a combo Firewire 800400 card with a TI chipset earlier
> this
The latest Test Branch SVN 3166, which according to the change log, "redone
vfo initialization", seems to improve the CW QSK significantly. The TX>RX
transition sounds better on the audio, no pop, now smooth sounding. My
Delay at 15ms seems best and quick.
I can also now set the Sample Rate
Tim,
Thanks, good info on how the temperature reporting works.
I'm not sure what the standards are on writing bug reports, release ver SVN
versions, but slight there is a difference in behavior of the Temp reporting
tool between release version 18.0 and Trunk 18.1 SVN 3165.
In the release v
Ah ha!
I have had less than stealer success using Firewire 800 cards (either 800 with
a bilingual cable or a 800/400 combo card) with the FLEX-5000 and FLEX-3000. I
tried a combo Firewire 800400 card with a TI chipset earlier this year on XP
and the driver that was required for it to load wou
Frank,
What is the text of the communication error? The problem may be with the MIDI
driver installation or something that was loaded subsequently that adversely
affected some of the driver components.
-Tim
-Original Message-
From: flexradio-boun...@flex-radio.biz
[mailto:flexradio
There will be a slight voltage drop when transmitting and a 0.2 VDC drop is
nothing to worry about. It looks like you have a well regulated power supply.
Due to the smaller footprint of the FLEX-3000, it has less thermal mass than
the FLEX-5000 (obviously), therefore it is going to heat up a bi
In the control panel does the radio show up as a sound card? What
operating system are you using?
73
Neal Campbell
Abroham Neal Software
Programming Services for Windows, OS X and Linux
www.abrohamnealsoftware.com
(540) 242 0911
On Sun, Jun 14, 2009 at 7:02 AM, Frank Goenninger wrote:
> Dudley
Dudley,
KB955408 is installed.
I do have a working communication connection between the Mac mini and
the F-5kA as the driver successfully loads and I can see the F-5kA
being shown correctly as a bus device in the driver control panel. So
there *is* a working connection between those two.
29 matches
Mail list logo
