From: Alfred Green n...@cox.net
Date: Fri, 16 Jul 2010 Time: 20:31:36
Guess who the poor sod is, that's been run over by the lawnmower?
I don't know who it is, but it's obviously someone who just ran over the
replacement antenna cable on his iPhone 4
--
73
Ian, G3NRW
Would anyone in Flex like to comment as to why none of these deals are ever
offered to us in the EU and why we always have to pay full RRP plus a bit more?
--
Message: 3
Date: Fri, 16 Jul 2010 20:31:36 -0700
From: Alfred Greenn...@cox.net
To: 'Flex
You can´t say this in general. Appello-Funk in germany offered Flex
1500 for 579,-- EUR before HamRadio (so only pre-order), 599,-- EUR at
HamRadio and now 649,-- EUR after...
Thats creative priceing, isn´t it?
73, martin dl1fux
Am 18.07.2010 12:53, schrieb Mike:
Would anyone in Flex
Hi Everyone,
I have a few questions about a Flex5000C I am working on for my friend's
remote control system.
We access the radio/antenna site via a fixed IP internet connection, and run
the audio (incoming/outgoing) link through a VOIP provider and audio hybrid.
1). How do I determine the
:
http://kb.flex-radio.com/
FlexRadio Homepage: http://www.flex-radio.com/
End of FlexRadio Digest, Vol 63, Issue 18
*
__ Information from ESET NOD32 Antivirus, version of virus
signature database 5288 (20100718) __
The message was checked
Can anybody recommend a linear amp and tuner that might work well with the
QRP 1500?
Thanks
W1APZ
___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives:
I assume you want 100 watts? If so you can get both in a compact package - a
FLEX-3000. :-)
For about the same cost and you get a higher sampling rate and better rx
performance.
-Tim
Sent from my iPhone
On Jul 18, 2010, at 1:03 PM, Al Zaba a...@gmx.com wrote:
Can anybody
I love it.
On 7/16/2010 11:31 PM, Alfred Green wrote:
Guess who the poor sod is, that's been run over by the lawnmower?
It doesn't look like Gerald.
In case this is too cryptic, take a look at our favorite site:
www.flex-radio.com
g 73, Alf NU8I
1). How do I determine the 5000C's Ethernet IP address and ports so that I
can program those into my router's NAT?
Goto command prompt (run 'cmd') then type 'ipconfigenter' and it will give ip
address
2). Can the 5000C provide CI-V level outputs to exploit the frequency
tracking features of
Hi all
I am considering offering an upgrade to the computer in the Flex-5000C and
have tested a couple of boards that might be candidates but I do not have a
5000C to understand how constrained it is for alternative configurations.
Therefore, if anyone has a 5000C they would be willing to let me
Hi:
This mornig I decided to install PSDR 2.0 Beta, performed all steps as per
instructions and got the same error message on both installation attemps. The
message I am getting is the following:
Erro Communicating with radio, the program will likely crash
Please update the radio firmware to
Uninstall your Firewire driver before running the PowerSDR v2.0 Beta
I tried to locate a radio firmware version 2.0 but could no find it, mine is
1.3.0.8.
Try the Knowledge Center
http://kc.flex-radio.com/KnowledgebaseArticle50441.aspx
-Tim
-
W4TME
-Original Message-
From:
The new firmware is in a folder in your Documents folder/library. Go looking
for it and you could upload it with the FlexDriver.
73
Neal Campbell
Abroham Neal Software
www.abrohamnealsoftware.com
(540) 645 5394 NEW PHONE NUMBER
Amateur Radio: K3NC
Blog: http://www.abrohamnealsoftware.com/blog/
Thank you,
The only thing the article didn't describe is where is the 5000c's output
where I connect the wire that runs to the CI-V
73, Scott W3TX
-Original Message-
From: flexradio-boun...@flex-radio.biz
[mailto:flexradio-boun...@flex-radio.biz] On Behalf Of Bill Dailey
Sent: Sunday,
Hi Scott,
You will need a serial (or USB) to CI-V adapter and then use a 3rd party
program called DDUtil. The setup works great and I'll email you a pdf I
wrote on how to configure it.
If anyone else would like a copy of the pdf, please contact me directly.
Dave
wo2x
SDR 1.18.5, latest firmware. Flex 3000. Windows 7 ultimate.
I left the F3K running overnight. Came back to check on it today, and the
SDR screen was frozen. I clicked on STOP, and the Windows Program has
Stopped Responding message came up. I chose to terminate.
I waited a minute, then tried
Hi Mark
A couple of suggestions!
For whatever reason, Microsoft has implemented a very short timer to report
back that a process is not responding, usually giving you the option to
switch to another program, wait, or cancel.
In almost all cases, its best to wait. If the program is still in this
Mark,
To add what Neil and Tim suggested, you might want to look at the Event
Viewer to see just what might have stopped before PowerSDR stopped
responding. Bet it might have been the some surge that might have the
12 dc going down differently from the computer, this can cause the FW
to
Neil and Tim:
Solved the problem, thanks for help. PSDR2.0 is great
73´s
Mario
- Original Message -
From: Tim Ellison telli...@itsco.com
To: Mario Aviles mario.avi...@amnetsal.com; flexradio@flex-radio.biz
Sent: Sunday, July 18, 2010 2:39 PM
Subject: RE: [Flexradio] Help with PSDR
19 matches
Mail list logo
