Matt,
As Neil said, be sure to check the Mixer menu and that the Mic is checked..
Then move the TX meter to Mic, this will be the first mic audio stage,
and increase you Mic Gain, most Mic will need at least 20 on the mic
gain..
As some else said, if you are using a computer type of mic, m
Bruce,
I have had good luck with this one , for PCI..
http://www.lacie.com/us/products/product.htm?id=10332
or
This one
http://www.newegg.com/Product/Product.aspx?Item=N82E16815118005&cm_re=firewire_card-_-15-118-005-_-Product
For PCIe
http://www.newegg.com/Product/Product.aspx?Item=N82E168
Go to the Mixer menu and make sure you have enabled the front Mic for input.
That gets me every time!
73
Neal
On Sun, Jul 3, 2011 at 3:51 PM, wrote:
> Hi,
>
> I haven't used my F3K for anything other than digital modes for a long
> time. Voice used to work fine with the same equipment I am usin
What kind of processor and how much and type of memory? I am interested
in running a 1500 under openSUSE in a VM if possible.
On 07/03/2011 02:21 PM, John Vandenberg wrote:
Just a note:
Have been running the Flex-1500 for 2 month now with no problems on my
Linux system in Virtual box together
___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/ Homepage: http://
Many computer microphones are electret, and around 5 volts is provided by
the sound card in a computer for them. Here is one more or less random
reference I found with Google:
http://www.hobby-hour.com/electronics/computer_microphone.php
I wonder if you need this voltage with the headset
Just a note:
Have been running the Flex-1500 for 2 month now with no problems on my
Linux system in Virtual box together with other stuff.
System details
- quad core AMD with 16GB Ram
- Ubuntu 10.10 Maverick
- Virtual box V4.0.10 (and older)
- WinXP-pro (in VBox)
Software
Yes Mike, it's a custom wiring job, but it has always worked in the
past. Tip is wired to mic+ and ring to mic-.
Some high end microphones do need a 48v bias voltage, but I don't think
a computer headset mic needs it. At least it never used to on mine.
I wonder if some RF got into the audio c
Hi Larry,
Yes, that is the factory default setting, and it is enabled and turned
up fully.
Thanks,
Matt
On 07/03/2011 03:00 PM, Larry Goga wrote:
Hi Matt,
Did you check the audio mixer panel in the main menu bar? Is the
microphone connector on the front panel enabled and the level set
ap
I am somewhat confused! My PC doesn't have a mic connector that matches the
mic connector on my Flex 3000. You may be using a computer mic with an
adapter. I think most computer mic's need a bias voltage for power, check to
see if you are getting that on your adapter from the 3K. If that mic setup
Hi,
I haven't used my F3K for anything other than digital modes for a long
time. Voice used to work fine with the same equipment I am using now,
but no luck.
With the radio on dummy load, I downloaded PSDR 2.0.22, did the
factory defaults reset, went to the voice band of 20 meters, chose
USB, and
I am trying to run WSJT on Digu (Flex 5000).
After I TX, the "MOX" stays on . ie: does not switch back to RX.
Do I have some option selected incorrectly?
Any help appreciated.
73 Kevin
___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.
Phil
You didn't mention if you had any CAT program running (DDutil, Fldigi, etc.)
at the time.
I run with CAT enabled all the time and have not noticed any delay.
Do you have the "Use Kenwood AI command" unchecked ?
Dave
-Original Message-
From: flexradio-boun...@flex-radio.biz
[mailto:
Thanks for the help Dudley, You hit the nail on the head, but then why would I
have expected anything else! Your instructions were dead on, and now both ssues
are resolved.
73's Jack K5FSE
Treas QRP ARCI
jack.nel...@mindspring.com
- Original Message -
From: FlexRadio Support,
I noticed that when I installed 2.1.2 RC3, PSDR started to lag for 1
second on each operation. After digging down a bit, I found that it
happened when I had CAT control enabled. So, when I wanted to use CAT,
control, I went back to 2.0.22. However, 2.0.22 started to do the same
thing randomly after
15 matches
Mail list logo