[Flexradio] PSDR v2.3.5 and CW Skimmer

Hi, Now that PowerSDR ver 2.3.5 supports 96 and 192khz in VAC, do anyone know if we allso can use 96 and 192khz in CW skimmer, or it's still only 48khz? 73, Jan, OY3JE ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.

Re: [Flexradio] F5K: Question regarding an external transverter on XVRXport

Hi Carsten, I am using the Kuhne TR1296H with my Flex-5000 Cables are set like this TR1296H IF TX > Flex XVTXCOM TR1296H IFRX(TX) > Flex XVRX Then make sure the TR1296H is setup for seperate TX/RX cable and SW inside transverter is correct. In the Flex, you dont use the Antenna Selection menu.

Re: [Flexradio] 2.0 Beta - Panadapter image

Hi George, Have same problem here, special on low bands and very bad at times on 10 and 6m. I have a uploaded a recording of 80m to youtube here http://www.youtube.com/watch?v=Ijy81tMxqp4 You can se it very easy if you use the Panafall and scroll the band up or down Have had this problem from ver

Re: [Flexradio] VAC mismatch between line one and line two

Steven, You must adjust bouth Line 1 and Line 2 under Control Panel, Soundcard to you needed SR As Simon allso did mention I think this must be added to the Flex KB, as it's not the first program opening the VAC that sets the SR of the VAC. 73 Jan, OY3JE -Original Message- From: flexra

Re: [Flexradio] Spur in PSK31 output even with no rfout into Dummyload.

there too. So thanks for the help Simon. 73, Jan, OY3JE -Original Message- From: flexradio-boun...@flex-radio.biz [mailto:flexradio-boun...@flex-radio.biz] On Behalf Of Simon HB9DRV Sent: 2. februar 2010 19:17 To: 'David Beumer W0DHB' Cc: 'Steven L Hess'; 'Ja

Re: [Flexradio] Spur in PSK31 output even with no rf out into Dummyload.

8k so this must be a problem. So my questions is if there is a way to force DM780 to 41000? 73 Jan, OY3JE -Original Message- From: Simon HB9DRV [mailto:si...@hb9drv.ch] Sent: 2. februar 2010 09:18 To: 'Jan Egholm'; 'Bret Mills' Cc: 'Steven L Hess'; FlexRa

Re: [Flexradio] Spur in PSK31 output even with no rf out into Dummyload.

Hi, I am using DM780 and have allways had this spur when running PSK 73, Jan, OY3JE Sent from my iPhone On 02/02/2010, at 01.54, "Bret Mills" wrote: Hi Steve, Try DM780 (HRD) and you can see what Tim is talking about, it doesn't have the sound card harmonic and is NOT a Flex issue. It is

Re: [Flexradio] PowerSDR & 3rd party software

s so well that it sometimes detects/decodes signals I can't actually hear by ear. And 'sometimes', on quiet nights, it prints callsigns that I can't detect visually in the CWSkimmer waterfall. On 12/22/2009 2:58:23 PM, Jan Egholm (j...@egholm.fo) wrote: > Hi, > > I am w

[Flexradio] PowerSDR & 3rd party software

Hi, I am wondering why we do not se any 3'rd party software that is fully supporting Direct I/Q on VAC and FlexRadio Audio device? This is the only transceiver out there with this possibillity, yet even this there is no software supporting this. Some of these software I refere to are MAP65, CW Sk

Re: [Flexradio] HRD - No Automatic LOTW

- No Automatic LOTW - Original Message - From: "Jan Egholm" > > But hope to se more softwares supporting the I/Q of PowerSDR. > Hi Jan, As I mentioned indirectly before, part of the problem is gaining access to documented I/Q interfaces to work with. For normal soun

Re: [Flexradio] HRD - No Automatic LOTW

No even CW Skimmer is using the I/Q 100% as it's only possible to decode 24khz and not 96 or 192khz I am very suppriest not to se requests of this, as this wood be hugh benefit for contesters and others using the Flex radio. So I did add a QS1R here to get this bandwith on CW Skimmer. But hope to

Re: [Flexradio] CW skimmer and N1MM logger

Hi, I works fine with DDUtil and N8VB vcom. Only thinkg that is missing is tha capabillity of CW Skimmer to decode 192khz when used with powerSDR, as it will only decode about 24khz. 73's Jan, OY3JE -Original Message- From: flexradio-boun...@flex-radio.biz [mailto:flexradio-boun...@f

Re: [Flexradio] Phantom signals on 6M

I use a software named Freez Screen Video Capture, but there are many different software out there to record a window. I have had this problem for log time, and have tryed all awaileble SVN out there, and the problem keep comming, so only solution I found is to restart the PoweSDR software. This

Re: [Flexradio] Phantom signals on 6M

Hi, Did the signals look like this http://www.youtube.com/watch?v=Ijy81tMxqp4&feature=channel_page ? The spikes I have allso seen on my F5K Regards, Jan, OY3JE -Original Message- From: flexradio-boun...@flex-radio.biz [mailto:flexradio-boun...@flex-radio.biz] On Behalf Of vtnn...@comcas

Re: [Flexradio] Images

I have allso same problem here. This problem have been for long time, and is still here after software & driver updates, and allso the radio is just back from repair (for other reasons) from Flex for 3rd time, but still same problem :-( I have used the Flex for a few contests, and this is very ver

Re: [Flexradio] Huge latency spikes

Hi Alan, Have same problem here. This is happening each time I receive a Email. I use Outlook & AVG Antivirus. But problem happens only after the PC have been running for some hours. 73, Jan OY3JE -Original Message- From: flexradio-boun...@flex-radio.biz [mailto:flexradio-boun...@flex-r

Re: [Flexradio] are we getting close to FSK yet

Hi, I have been running a few RTTY contests with my F5K. I never used FSK on my other rigs, but cant se what the differance is on running RTTY in FSK when ALL other digital modes are using audiocables and in the F5K case it will be a VAC. The problem I can agree on is that the PowerSDR is not disp

Re: [Flexradio] DM780 and PowerDSR question with FLEX-5000A

Hi Jay, I have seen same problem, and this happens if I have used wrong soundcard (Flex Radio 5000 SPDIF) on the TX or input on DM780 or other digital Software. In my case is DM 780 setup for: Input device is Virtual Cable 2 and Source is Line, Output Device is Virtual Cable 1 and Device Wave. An

Re: [Flexradio] Audio & Latency

ilto:[EMAIL PROTECTED] Sent: 3. december 2008 20:58 To: Jan Egholm; flexradio@flex-radio.biz Subject: RE: [Flexradio] Audio & Latency For item #1, what is the Firewire driver operation mode? If it is SafeMode1 set it to SafeMode2 What is the sampling rate and buffer size set for the Firewir

[Flexradio] Audio & Latency

Hi, I have two problems I have been trying to solve, and have not managed to do this yet. 1. The first problem is glitches in the audio. These do happen when loud audio is present, and I allso hear this in the phones jack on the F5K. Allso the audio can stop if I do open a software window or the

Re: [Flexradio] CW Skimmer 196khz

g, I can't get it to decode anything outside +/-12kHz of my QRG. But if there is a way to get it to decode 96 or 192kHz I realy wood like to know how to set it up. 73, Jan OY3JE -Original Message- From: Edward Russell [mailto:[EMAIL PROTECTED] Sent: 28. november 2008 02:20

Re: [Flexradio] CW Skimmer 196khz

:[EMAIL PROTECTED] On Behalf Of Jan Egholm Sent: 27. november 2008 21:43 To: 'Jan Egholm'; 'Dudley Hurry' Cc: flexradio@flex-radio.biz Subject: Re: [Flexradio] CW Skimmer 196khz Looks like this is a Skimmer issue and nothing to do with F5K or VAC I will need to have a very la

Re: [Flexradio] CW Skimmer 196khz

! 73, Jan, OY3JE -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Jan Egholm Sent: 27. november 2008 17:57 To: 'Dudley Hurry' Cc: flexradio@flex-radio.biz Subject: Re: [Flexradio] CW Skimmer 196khz Dudley, Yes, Audio is comming in to CW Skimmer

Re: [Flexradio] CW Skimmer 196khz

To: Jan Egholm Cc: flexradio@flex-radio.biz Subject: Re: [Flexradio] CW Skimmer 196khz Jan, Make sure that you have "Output to VAC" checked in the Setup => Audio => VAC tab.. 73, Dudley WA5QPZ Jan Egholm wrote: > > Hi, > > > Skimmer have been working fine he

[Flexradio] CW Skimmer 196khz

Hi, Skimmer have been working fine here with VAC 196khz, but today I cant get it to decode outside the waterfall on the Skimmer, I can only se 16khz on skimmer even F5K is set to 196. I have rechecked all settings several times but can't get it to work again. Anyone have a clue where the probl

Re: [Flexradio] CAT interface

15 To: Jan Egholm; flexradio@flex-radio.biz Subject: Re: [Flexradio] CAT interface Natively, two applications can not use the same com port (virtual or physical) at the same time. However, Steve has written are really cool application that aggregates and controls the behavior of multiple CAT en

[Flexradio] CAT interface

Hi, I am trying to get two or more app to read the frequency from the PowerSDR at same time. This looks not to be easy as this must bee done via virtual serial cable. I want one app to bee able to use TX/RX in the CAT interface and the other APP's shall only RX on the CAT. In my case I have CW

Re: [Flexradio] PowerSDR V1.12.0 Stops

Hi, I have allso a freezing problem, but have found out that this happens when receiving Email, so it's either Outlook or AVG antivirus that couses this in my case. So it's a very bad idea to check Email when in a pileup :-) Jan, OY3JE -Original Message- From: [EMAIL PROTECTED] [mailto

Re: [Flexradio] Dual mode display panadapter and waterfall - help

Yes you did just needed to drag the window down to enable dual screen, and this was in all my latest versions until 1.12.0 But I cant got back as I have the latest firmware now in the F5K And if you look at 5th page in the nice review from QST, you will se the window is draged down and the panada

Re: [Flexradio] Dual mode display panadapter and waterfall - help

Tim, I was allso verry happy for the dual function of Panadapter & Waterfall, in previos PWSDR version. But this is not in ver. 1.12 :-( I did think this was maybe a mistage an there wood be an update that corrected this, but now you say this must be reported as an "enhancement" ? This is not an