Re: [j-nsp] fpc2 message...

2010-12-21 Thread Alex
Hi there, How do you measure CPU? Is it FPC CPU or MS-PIC CPU? show services service-set summary will show you the MS-PIC CPU per service-set and my guess it could be very different from FPC CPU in show chassis fpc. HTH Regards Alex - Original Message - From: Derick Winkworth

[j-nsp] default_arp_policer

2010-12-21 Thread ibariouen khalid
Dear all Can someone tell me what is the default value of default_arp_policer ? is there any recommendation to reduce the values ;because i have an issue with an ARP storme and the router is impacted . thanks a lot ___ juniper-nsp mailing list

Re: [j-nsp] default_arp_policer

2010-12-21 Thread Felix Schueren
On 21.12.10 17:20, ibariouen khalid wrote: Dear all Can someone tell me what is the default value of default_arp_policer ? is there any recommendation to reduce the values ;because i have an issue with an ARP storme and the router is impacted . the major problem with the default arp

[j-nsp] logical router with physical Interco

2010-12-21 Thread juniper light
Hi guys, I would like to use M10 to simulate 3 PE, using logical-routers ( Junos 8.4R4.2 ) I connected 2 fastethernet back-to-back, link are UP. but when I tried configuring vlan-id , I cannot ping from one Logical router to the other : first scenario using Vlan-tagging : set logical-routers

Re: [j-nsp] logical router with physical Interco

2010-12-21 Thread Cristian Frizziero
Hi!! I'd try to change ports pairs, and to switch the PIC to a different fpc slot, just to be sure that there is no hardware issue The configuration looks fine Cristian El 21/12/2010 15:07, juniper light escribió: Hi guys, I would like to use M10 to simulate 3 PE, using

Re: [j-nsp] Juniper SRX and ssh freeze

2010-12-21 Thread Alfred Schweder
Hello I don't know about the SRX, but I know with the SSG, the ScreenOS default timeout for TCP sessions was way too low (IIRC something like 5 minutes) and would cause that. I turned on SSH keepalives to avoid the timeout. Does SRX support ssh keepalive (like M- or J-serie)? SSGs drop

Re: [j-nsp] logical router with physical Interco

2010-12-21 Thread juniper light
I didn't change cabling, but I connected a new interface to annother router and I'm having the same problem, the new interface is in the default configuration : set interfaces fe-0/3/2 unit 0 family inet address 10.0.24.2/30 ad...@m10 show interfaces terse Interface Admin Link Proto

Re: [j-nsp] logical router with physical Interco

2010-12-21 Thread Cristian Frizziero
Ok, It looks like a hardware problem (at PIC or EFEB level, may be). I´d be a good idea to change the cable too just in case Check with show log chassid , may be you can find some log related to a physical problem. Also check with a show route logical-router PE2 or PE3. You must find

Re: [j-nsp] Juniper SRX and ssh freeze

2010-12-21 Thread Julien Goodwin
On 22/12/10 04:53, Alfred Schweder wrote: Does SRX support ssh keepalive (like M- or J-serie)? SSGs drop the ssh session if they get a keepalive. Juniper isn't willing to fix this in the near future ;-( For my SRX at the office back when I installed it (9.6 IIRC) *TCP* keepalives would not

Re: [j-nsp] Juniper SRX and ssh freeze

2010-12-21 Thread Barny Sanchez
Yes it is supported in SRX, and you are right not supported in ScreenOS, it drops it. Thanks! - Barny On Dec 21, 2010, at 8:08 PM, Julien Goodwin jgood...@studio442.com.au wrote: On 22/12/10 04:53, Alfred Schweder wrote: Does SRX support ssh keepalive (like M- or J-serie)? SSGs drop the