For health reasons, I will be disposing of this project. It is a partially
(and lovingly) constructed 1976 plans-built KR 2. It is a small 2 place, VW
powered, plane designed to cruise in the 130-134 MPH range. Since I was 6'1"
tall the cockpit was designed to be comfortable for a pilot of this si
I still have my project for sale. It is a very straight and solid boat with
all the KR fiberglass to complete the top. Fiberfrax for the firewall and
stainless steal if you want it.
Jim Ellison
Sherman, Texas
missile.mo...@hotmail.com
903-815-3231
> _
> Se
To KR Knetters,
Health matters have dictated an end to my dream.. I have a KR-2 In canoe
form with wing stubs attached and sitting on original KR retractable landing
gear. Vertical and horizontal tail feathers are attached and front and rear
wing spars have been built but not attached.
I ha
As much as I hate to, I have a KR-2 Project for sale. It is time to make
the decision and realize my dream will not materialize..
For more information on the project E-Mail Paul @ _Kr1pilot@hotmail.com_
(mailto:kr1pi...@hotmail.com)
Please serious inquires only..
1 11:06 AM
Subject: KR> Kr-2 Project for Sale
> It's time for me to close shop, so I have a KR-2 project looking for a new
> home.
>
> As well I have a 66 corvair engine partially torn down.
>
> Send all inquires to kr1pi...@hotmail.com.
>
It's time for me to close shop, so I have a KR-2 project looking for a new
home.
As well I have a 66 corvair engine partially torn down.
Send all inquires to kr1pi...@hotmail.com.
Projects located in central florida..
KR-2 project for sale skin removal
One way to remove the skins while leaving the skeleton ready for new skins
might
be to use a router. Set the cutting blade the depth of the skin and get a blade
for the router the width of the skeleton sticks.
Rout down the skins over the skeleton sticks
One way to remove the skins while leaving the skeleton ready for new skins
might
be to use a router. Set the cutting blade the depth of the skin and get a blade
for the router the width of the skeleton sticks.
Rout down the skins over the skeleton sticks, unless you intend to re-use the
skins.
Original Message
What would be a good procedure for removing existing fuselage skin and leave
surfaces good for applying new skin?
If you must remove the skin, try using a steam iron. let it set on the first
part of the area you want to remove and when it gets real hot, just use a
wedge to li
-Original Message-
What would be a good procedure for removing existing fuselage skin and leave
surfaces good for applying new skin?
END
I would cut the ply out between the 5/8" spruce and then use a Dotco type
grinder to get is close. Maybe use a block sander with about
DON'T, spend the time finishing the project and go FLY, Virg
On 11/6/2010 3:22 PM, ttcse/Tom wrote:
> What would be a good procedure for removing existing fuselage skin and leave
> surfaces good for applying new skin?
>
>
>
>
What would be a good procedure for removing existing fuselage skin and leave
surfaces good for applying new skin?
> The Bad -
>
> 2. The builder did really nice work on the spruce. Something was lost
> in translation on the fuselage skin and it was not installed correctly. It
> should
--Original Message--
From: Steve Glover
Sender: krnet-bounces+q500=msn@mylist.net
To: virg...@bellsouth.net
To: KR Net
ReplyTo: n92...@cox.net
ReplyTo: KRnet
Subject: Re: KR> KR-2 project for sale.
Sent: Nov 6, 2010 8:38 AM
I know. It is stronger as well but the mahogany looks ni
R-2 project for sale.
Sent: Nov 6, 2010 05:14
Birch is an acceptable plywood for the KR series. It was sold in
the wood kit, Virg
\On 11/6/2010 12:14 AM, I FLY KRs wrote:
> Netter's,
>
>
>
> I have a standard KR-2 project for sale. This is a great start on a build
Birch is an acceptable plywood for the KR series. It was sold in
the wood kit, Virg
\On 11/6/2010 12:14 AM, I FLY KRs wrote:
> Netter's,
>
>
>
> I have a standard KR-2 project for sale. This is a great start on a build
> for not a lot of cash.
>
>
>
> The Good -
>
>
>
>
> The Bad -
>
Netter's,
I have a standard KR-2 project for sale. This is a great start on a build
for not a lot of cash.
The Good -
1. The boat is assembled.
2. Spars and tail frame is built.
3. Prefabricated components include canopy frame, wings tips, forward
deck/ instrument pan
Please check out my Barnstormers.com ad for a kr2 project for sale.
Address is www.barnstormers.com, find Experimental, then Rand Robinson.
Thanks,
Jim Foster
Katy, Texas
A very nice project is for sale. Boat stage with Revmaster 2180 and
other stuff. Buying Mooney. No time to build. For photos and more
info contact:
mlw...@hotmail.com
19 matches
Mail list logo
