"Michael R. Jinks" wrote:
No you shouldn't need swap, but it's possible the installer won't let
you proceed without it. The spare partition won't be picked up as swap
unless it's flagged by fdisk/diskdruid as a swap partition (type 82).
Alright, thanks for trying. I did double check a few
Hello Everyone:
I have just installed RH 7.0 (Respin) and I had a problem getting past
DiskDruid. I used fdisk to set a Linux partiton on hdb3 and selected it
for the mount point. However, once this was done (I tried several times)
the "NEXT" button would not work. "Manually Partition with
The Next button won't work if you haven't configured enough partitions
with proper mount points. Chances are you filled out something wrong in
diskdruid.
First of all, as I read your post you set the disk device as the mount
point; this isn't right. I may be reading incorrectly but the mount
"Michael R. Jinks" wrote:
The Next button won't work if you haven't configured enough partitions
with proper mount points. Chances are you filled out something wrong in
diskdruid.
That's what I thought, that's why I tried several times before doing
anything else. The 6.2 and 7.0 installers
No you shouldn't need swap, but it's possible the installer won't let
you proceed without it. The spare partition won't be picked up as swap
unless it's flagged by fdisk/diskdruid as a swap partition (type 82).
I've run into swap on machines with 192MB of swap before, FWIW, though
of course not
Okay the saga continues...
If I power off the machine and leave it for a while it MAY start up however
it gives a segmentation fault for just about every service it starts. Most
of the time though it will not start. It is giving the segmentation fault
errors prior to the problems spawning the
On Mon, 5 Feb 2001, shoe wrote:
Okay the saga continues...
If I power off the machine and leave it for a while it MAY start up however
it gives a segmentation fault for just about every service it starts. Most
of the time though it will not start. It is giving the segmentation fault
errors
1 12:55 PM
To: [EMAIL PROTECTED]
Subject: RE: RH 7.0 install problem
On Mon, 5 Feb 2001, shoe wrote:
Okay the saga continues...
If I power off the machine and leave it for a while it MAY start up
however
it gives a segmentation fault for just about every service it starts. Most
of the t
On Fri, 2 Feb 2001, shoe wrote:
I've tried upgrading from 6.2 to 7.0, I've tried a custom install, server,
and workstation installs and all render the same error message when booting
up the first time.:
INIT:Entering runlevel 3
INIT: Id "1" respawning too fast: disabled for 5 minutes
On Sat, 3 Feb 2001, Kyle Hargraves wrote:
On Fri, 2 Feb 2001, shoe wrote:
I've tried upgrading from 6.2 to 7.0, I've tried a custom install, server,
and workstation installs and all render the same error message when booting
up the first time.:
INIT:Entering runlevel 3
INIT: Id
On Sat, 3 Feb 2001, Mikkel L. Ellertson wrote:
On Sat, 3 Feb 2001, Kyle Hargraves wrote:
On Fri, 2 Feb 2001, shoe wrote:
I've tried upgrading from 6.2 to 7.0, I've tried a custom install, server,
and workstation installs and all render the same error message when booting
up the
On Sun, 4 Feb 2001, Kyle Hargraves wrote:
On Sat, 3 Feb 2001, Mikkel L. Ellertson wrote:
On Sat, 3 Feb 2001, Kyle Hargraves wrote:
On Fri, 2 Feb 2001, shoe wrote:
I've tried upgrading from 6.2 to 7.0, I've tried a custom install, server,
and workstation installs and all
Hello,
I've been trying to install RH 7.0 on a little box with little success. It
is a P166 wth pretty standard hardware, in fact it runs RH 6.2 just fine.
I've tried upgrading from 6.2 to 7.0, I've tried a custom install, server,
and workstation installs and all render the same error message
13 matches
Mail list logo
