Vertex Standard VX-2200 and 4200 series radios can be channel changed via BCD
addressible pins from the rear sub DB15.
We utilise a UHF link radio (VX-2200 or 4200) to send 5 Tone commands that
can be addressed via a configurable BCD output that can change the frequency
and of course pass
Still looking for a reed.
Jim, K8COP
Hi,
New member here. Thanks for allowing me to join.
Our club has acquired some large lead-acid 12v batteries we would like
to use to back up our repeater in emergency situations. Does anyone
know of a good (but simple and inexpensive [we are a very small group
in a very small town]) circuit
CPI Communications has several Tone Remote products as well, but as
mentioned the multi-channel control equipment is mainly for Motorola and
Kenwood. That said if you radio can support BCD control you might be in
luck.
http://www.cpicomm.com
-Sean
Some info can be found on the Midian site
Hi all you know they say there is no dumb question unless you didnt
ask it and messed things up so here goes .I am wanting to make a cheap
repeater system for 2 meter and I really need some input on how to put
one together and also once its built is there a special licence to
operate it?Thanks
CPI Communications has several Tone Remote products as well, but as
mentioned the multi-channel control equipment is mainly for Motorola and
Kenwood. That said if your radio can support BCD control you might be in
luck.
http://www.cpicomm.com
-Sean
Some info can be found on the Midian site
Ron,
Yes, as a matter of fact, we are using half-duplex transceivers for each
link, and some links go through multiple hops which makes your 24
input tail beep generater method unusable.
We do infact put a tail beep on each transceiver (only when the received
signal is coming in on the
* IF YOUR NICE I MAY TELL YOU [EMAIL PROTECTED] [2007 Jan 09 06:55 -0600]:
Hi all you know they say there is no dumb question unless you didnt
ask it and messed things up so here goes .I am wanting to make a cheap
repeater system for 2 meter and I really need some input on how to put
one
Hi ALL
I have an MFJ-2040 Autopatch repeater controller. I deperately need the
manual for it. Can anyone please help? Thank you!
Dave
http://www.surplussales.com/Manuals/man_mfj.html
Has it listed available for $10.. Mike
w2drh wrote:
Hi ALL
I have an MFJ-2040 Autopatch repeater controller. I deperately need the
manual for it. Can anyone please help? Thank you!
Dave
Heh... Same thing I found; Google is your friend. grin
Richard, N7TGB
-Original Message-
From: Repeater-Builder@yahoogroups.com
[mailto:[EMAIL PROTECTED] Behalf Of Mike Pugh
Sent: Tuesday, January 09, 2007 6:57 AM
To: Repeater-Builder@yahoogroups.com
Subject: Re:
what equipment are you using now?
astron makes a automatic switch (it automagicly switches from AC to DC with
loss of AC)
there are a couple other makers, I'm sure.
you'll also have to consider battery charger(s) too.
wm5c [EMAIL PROTECTED] wrote:
Hi,
New member here.
Mathew Quaife wrote:
Actually I have several 56 splits. When I ordered the xtal, I
ordered for high side injection, and it does not want to tune up real
well. Put a 147.78 LSI, and it tunes to better than -110 dBm. So
this is the reason I want to try a 66 split and see if it will do any
Ok thanks wheres a good site that tells how to do all of this? 73's
From: Nate Bargmann [EMAIL PROTECTED]
Reply-To: Repeater-Builder@yahoogroups.com
To: Repeater-Builder@yahoogroups.com
Subject: Re: [Repeater-Builder] Vhf Repeater
Date: Tue, 9 Jan 2007 07:11:22 -0600
* IF YOUR NICE I MAY TELL
I have had good luck using a pair of diodes to isolate a power supply
from a charging circuit. I essentially have a Statpower 10amp battery
charger (specifically designed for the flooded cells I am using). The
batteries float on the charger voltage when the AC power is available.
The battery
A really simple circuit that I have used in a couple of repeaters uses
three power diodes and a resistor. Select diodes that will carry the
repeater load at about 50% of their rating.
Place one diode in series with the power supply to the repeater. This
one keeps the voltage from backing up
I have to agree with Dave. Using the proper charger or power supply for
keeping the batts up. I have my batteries housed in a stainless steel
enclosure that is anchored into concrete outside my ham shack. I learned the
hard way about using the proper charger... I just tapped into my repeaters
Hi group,
I am looking to buy the following items for a ge mastr vhf highband
base factory preamp part # 19c320215g1 or 19c320215g2 for 147.690 mhz
and if anyone has the premade n female bulk mount to bnc male cable
assemblys and the bnc male to rca male commonly found in units that
have the
I had a similar experience: I had a couple of deep cycle batteries in an
outdoor steel enclosure that I would charge periodically by connecting a
standard automotive charger. At times I would forget it was connected, so
eventually the batteries were cooked. After some research on the web, I
very true.. Mike
Richard wrote:
Heh... Same thing I found; Google is your friend. grin
Richard, N7TGB
-Original Message-
From: Repeater-Builder@yahoogroups.com
[mailto:[EMAIL PROTECTED] Behalf Of Mike Pugh
Sent: Tuesday, January 09, 2007 6:57 AM
To:
One source of (almost) free diode pairs is any alternator shop. The
common configuration of diodes in an alternator has three on a
plate, and two plates. One plate is common anode, the other plate
is common cathode.
The common failure mode is that one diode opens or shorts and the
technician
At 05:11 AM 01/09/07, Nate Bargmann N0NB wrote:
* IF YOUR NICE I MAY TELL YOU [EMAIL PROTECTED] [2007 Jan
09 06:55 -0600]:
Hi all you know they say there is no dumb question unless you didnt
ask it and messed things up so here goes .I am wanting to make a cheap
repeater system for 2 meter
Kent Chong wrote:
Hello,
Would like to control ICOM, and Vertex radio remotelly by using the
tone, for example, change channel, PTT etc. Anybody know the remote
control tone standard? Where could I find the informtion?
Best Regards,
Chong Kwan Meng
Hello Kent:
I'm not sure if
* frank james73 [EMAIL PROTECTED] [2007 Jan 09 10:43 -0600]:
Ok thanks wheres a good site that tells how to do all of this? 73's
http://www.repeater-builder.com/rbtip/
Google will reveal many more.
73, de Nate
--
Wireless | Amateur Radio Station N0NB | Successfully Microsoft
At 07:31 PM 01/08/07, you wrote:
Hi,
New member here. Thanks for allowing me to join.
Our club has acquired some large lead-acid 12v batteries we would like
to use to back up our repeater in emergency situations. Does anyone
know of a good (but simple and inexpensive [we are a very small group
The simplest way is just to get the IOTA supply and
float it across the battery. Thats it, nothing else
needed. Get an IOTA big enough to power whatever you
have, and still have some left over for charging. You
don't need (or want) diodes, resistors, or relays.
It shouldn't be that easy, but in
Danny,
If your batteries are flooded wet cells, as distinct from sealed (VRSLA or
AGM) types, you should take care to vent them to the outdoors. Wet cell
batteries also require regular monitoring for electrolyte levels and
specific gravity.
If your power supply has any kind of crowbar device in
27 matches
Mail list logo