!
Gordon Watson.
.. no
rot no holes.no movement..recommended.
Gordon Watson.
Kevin,
Congratulations. thats very believable
as a forney.I particularly like the tapered stack,
and firebox profile..
Gordon watson.
Wood Part no:T98 would suit.
Marks fax no : 0011 44 1787 238458.
Gordon Watson.
which can make excess steam from gas firing in
non drafted boilers, and is an easier production job, which is why it
persists in use, and there is nothing wrong with it applied to a siutable
model.
Gordon Watson.
testing on
my track as it has on ground level, and raised track with metal and timber
deck and a variety of rail/track brands..
gordon Watson.
was lit up and
fussed over /lubed and prepared by the driver, then thats what I want to do
as well..it seems they are marketing it to the switch on and run crowd.no
knowledge needed! I think we may hear some grievous stories in the future.
Gordon Watson.
rolled bar flat stock..when you come back the next day it will
have bowed as much as 2 or 3mm over 400mm lenght as stresses relieve..which
is very! irritating...
Gordon Watson.
around 2000km of 2 ft gauge still in
use for sugar trams..
Gordon Watson.
and the black
is a very thin[molicular copper oxide layer] I find it best to give two
treatments, drying off and buffing with soft cloth between this gives a much
more durable and even coating.
Gordon Watson.. Australia.
and no whistle, with a generally quie ter performance.
Gordon Watson.
!
Gordon Watson.
fyou ask for a G jet or HM jet you will get the right
thing..tap needed for the jet holder is 4.5mm by .5 mm pitch.. this may be
hard in Brissy.. if so mail your jet holder to me and Ill do it..
Gordon Watson.
And it arived here in wildest Victoria[OZtoday ] and its a ripper, thanks
Art.
Gordon Watson.
Royce,
I have 1/16th piping on dead leg lubricators, but with short
direct. route[about 1 long ] for longer runs 1/8th works ok, make the
offtake from the lubricator removable and fit up with 1mm hole to start
with, can always enlarge by small steps until youre happy with the feed
.
Gordon Watson.
Richard,
For the whistling burner, wrap stainless steel insect screen
round the burner, tightly,, 2 layers..
for the axle pump, remove the balls, clean the seats with a D bit, install
new balls[after the tap the ball in the seat trick] brings tears to the
eyes! these pumps supply
Art,
Yes its a JVR type C 2 off 1/2 inch tubes..I think it might be the
fairly large smokebox volume and the choke of the petticoat looks larger
than some other Asters Ive run. whatever it works!
Gordon.
] but
at least it looked Pommie.It steams well and tracks well but seems a litle
slippery on its feet, track was oily though and that didnt help..
Gordon Watson
,very good! absolutely leak free. but again needs to be very carefully
sized so that flow resistance is as low as possible the silicone tube
internal diameter should be about0.002 smaller than the sleeve.
Gordon Watson
Argyle has had a chinese origin combination slip roll/shear and brake for 7
years now .used every day..tend to be poorly set up when you buy it but
worth its weight in gold.
we grind the shear blades yearly and dont let Father in law crop hardened
screws to length on it! the regrind cost $80
castings..you
will need to discuss shrinkage factors etc before pattern making.
Gordon Watson.
a plate glass surface this will show up all sorts of posible leak
areas.But I do think fitting a set of David Baileys trucks is the best move.
Gordon Watson.
Flouty,
Its been done .commercially..German co in 1980s
Ive got a section drawing of a 2-8-2 tanker in HO scale..worked on 18vdc
resistance heater in horizontal boiler..can mailk you a drawing copy if you
like.
Gordon Watson.
Mike,
Very nice indeed.I love the polished boiler! I assume its 7/8 scale?
looks tall enough..
Gordon Watson
.
Gordon Watson.
for those interested in lateral thinking.O. Bullied while CME of Eire
National Railways in 1950,s built and ran a Locmotive somewhat like a small
Jawn Henry [NW] in looks,,it had piston valved engines in each bogie[truck]
a boiler which was double ended and fired by stoker in a firebox at the
Larry,
Basic data for gas burners..
To steam 10mm[3/8] cylinders. air mixing chamber inside diameter 3/8
lenght from face of gas jet to entry into slotted tube 20mm.2 air holes 6mm
dia half way along the chamber...jet holder to be a sliding fit in outer end
of air mix chamber, grub screw
My experience has ben good with cement sheeting, although it does need
timber edgeing to prevent crumble [it seems to get brittle after 4 or 5
years.] but one method I can endorse is to use Cable tray..this is used in
high rise buildings to carry electric cables its galvanised ,made from
pressed
Ive followed this with interest..becuase Ive had the Plastic plate in Mamods
blow out while running ,very scary[but not real dangerous!] the type of
water glass on the Merlin /Beck locos is easy to make. Body from 3/8 sq
brass . milled channel in center with bolt holes around outside, recess
/brasses/ but not all bronzes and not silver solder.
Trade name is "Ebonol" The coating /colour is copper oxide.
Gordon Watson.
of the brass with nail polish.
[4] immerse in Ferric chloride solution for 20 minutes .
[5] rinse of in water, remove the masking with thinners .
Radio shacks etchant for circuit boards is ferric chloride..about 10%
only.
Gordon Watson.
warmed through and runs like the wind! and
no reheating was fitted..
Gordon Watson.
is present!
gordon Watson.
Jun,
I have not recievde any reply from Locosteam from several enquiries
over many months,, I dont think they wish to deal outside of UK.
Gordon Watson
- Original Message -
From: "sslivesteam" [EMAIL PROTECTED]
To:
, axle pumps, working side tanks and
baldwin 4 bar crossheads[ which are a B to fit up!each one took
150 hours too build and where sold for about half thier true value..a good
first lesson in this business.
gordon Watson.
36 matches
Mail list logo