: XenServer vs XCP-NG
Sorry I have to ask, I see XenServer is listed, but i donbt see any
documentation for XCP-NG,
i know it was previously supported. Is it still supported and what is the
supported versions? as 3.0
is now in the wild. Thanks
--
Sent with Vivaldi Mail. Download Vivaldi for free
Sorry I have to ask, I see XenServer is listed, but i donbt see any
documentation for XCP-NG,
i know it was previously supported. Is it still supported and what is the
supported versions? as 3.0
is now in the wild. Thanks
--
Sent with Vivaldi Mail. Download Vivaldi for free at vivaldi.com
Hi Rene,
Is your zone type basic or advanced with security group in that case you want
to change xenserver/xcp-ng network back end to bridge . I am suspecting this
since the message has bridge in it otherwise it should use openvswitch.
Regarding SR , cloudstack can use any type of storage
that it says failed to configure brige(typo) firewall, but what can I
do to fix that? Or what did I miss?
And another question I have regarding a Xenserver setup, can cloudstack
utilize any kind of SR storage or only fibre channel?
Cheers,
Rene
ack setup on Xenserver with CEPH as
> Storage (both Primary n Secondary) . insight on this will be very
> helpful.
>
> Regards,
> Ranjit
>
Hello,
There are mixed reviews on Cloudstack setup on Xenserver with CEPH as
Storage (both Primary n Secondary) . insight on this will be very
helpful.
Regards,
Ranjit
, getting
> >> > >> following
> >> > >> > error while we are trying to reinstall the services.
> >> > >> >
> >> > >> > =
> >> > >> > root@cloudstack1:~# sudo apt-get --reinstall install
> >> cloudstack-usag
t;> > >> > Reading state information... Done
>> > >> > Some packages could not be installed. This may mean that you have
>> > >> > requested an impossible situation or if you are using the unstable
>> > >> > distribution that some required packages have not yet been created
>> &
= 4.16.1.0~bionic)
> but
> > >> > 4.17.0.0~bionic is to be installed
> > >> > E: Unable to correct problems, you have held broken packages.
> > >> > =====
> > >> >
> > >> > Thank you,
> > >&g
>> >
> >> > > Hi Ranjit,
> >> > >
> >> > > CloudStack management and usage have to be on the same version, can
> >> you
> >> > > please check the version of CloudStack usage server and verify if
> the
> &
com> wrote:
>> >
>> > > Hi Ranjit,
>> > >
>> > > CloudStack management and usage have to be on the same version, can
>> you
>> > > please check the version of CloudStack usage server and verify if the
>> > > upgrade to 4.17 h
upgrade to 4.17 happened properly. If not on 4.17, can you please try
> to
> > > upgrade the usage server?
> > >
> > > Please paste the exact error from the management server or usage server
> > > logs that you are seeing.
> > >
> > > Thanks,
> > > Harikrishna
> > &
ent server or usage server
> > logs that you are seeing.
> >
> > Thanks,
> > Harikrishna
> >
> >
> > From: Ranjit Jadhav
> > Sent: Saturday, June 18, 2022 5:53 PM
> > To: users@cloudstack.apache.org ; dev <
>
> Sent: Saturday, June 18, 2022 5:53 PM
> To: users@cloudstack.apache.org ; dev <
> d...@cloudstack.apache.org>
> Subject: ACS Upgrade Failed :: Xenserver
>
> Hello,
>
> While attempting to upgrade ACS from 4.16.1 to 4.17 on Xenserver, we faced
> the following issue. It appea
the management server or usage server logs
that you are seeing.
Thanks,
Harikrishna
From: Ranjit Jadhav
Sent: Saturday, June 18, 2022 5:53 PM
To: users@cloudstack.apache.org ; dev
Subject: ACS Upgrade Failed :: Xenserver
Hello,
While attempting to upgrade ACS from
Hello,
While attempting to upgrade ACS from 4.16.1 to 4.17 on Xenserver, we faced
the following issue. It appears that "cloudstack-management" and
"cloudstack-usage" requires different versions of cloudstack-common.
With cloudstack-common=4.17 Management, services are workin
What he said ^^^, as the XenServer upgrade effectively does backup of the
old partition data, and installs a brand new OS - with no ACS
plugins/scripts - so you have to initialise the host, to force ACS to copy
again all the binaries.
Best,
On Thu, 2 Jun 2022 at 06:14, Harikrishna Patnala
Hi Vivek,
Please check the CloudStack detected Xenserver version in either UI or database.
You may try an option to reinitialize the Xenserver host by clearing the tags
on the host and try reconnecting from CloudStack UI.
Run the following command on Xenserver and reconnect the host
Hi Vivek,
This discussion thread might provide you some inputs:
https://lists.apache.org/thread/7q6yybm3qcms21qcd8945kvrygpr1v86
Also, check the docs here:
http://docs.cloudstack.apache.org/en/4.16.1.0/installguide/hypervisor/xenserver.html#upgrading-xenserver-versions,
and see if you have
Hello Guys,
We have recently upgraded our XenServer from 7.1 to 8.2. We are using
CloudStack 4.16.1. But after the upgradation my status of host is showing
alert. I have gone through the logs getting below error. Can someone help me
out
;In
> > CloudStack 4.X.0, this plugin only supports the KVM hypervisor with the
> > standard linux bridge."
> >
> > Is this correct?...that I cannot use VxLAN with XenServer/XCP-NG ?
> >
> > thanks in advance
> > Matt
> >
>
>
> --
> Daan
>
t;
> I am in need of a quick confirmation.
>
> I am reading in the latest documentation for the VXLAN Plugin that "In
> CloudStack 4.X.0, this plugin only supports the KVM hypervisor with the
> standard linux bridge."
>
> Is this correct?...that I cannot use VxL
Hello,
I am in need of a quick confirmation.
I am reading in the latest documentation for the VXLAN Plugin that "In
CloudStack 4.X.0, this plugin only supports the KVM hypervisor with the
standard linux bridge."
Is this correct?...that I cannot use VxLAN with XenServer/XCP-NG
e the same
example as in our blog page)
Best,
On Tue, 15 Jun 2021 at 01:17, Felipe wrote:
> I put in allow.additional.vm.configuration.list.xenserver:
>
> HVM-boot-params%3Aorder%3D%22dcn%22
>
> it didn't work, do you have an example to change the order of bios on HVM
> on xenserver?
I put in allow.additional.vm.configuration.list.xenserver:
HVM-boot-params%3Aorder%3D%22dcn%22
it didn't work, do you have an example to change the order of bios on HVM on
xenserver?
Thank you!!
On 2021/06/14 22:32:24, Andrija Panic wrote:
> https://www.shapeblue.com/cloudstack-feat
https://www.shapeblue.com/cloudstack-feature-first-look-enable-sending-of-arbitrary-configuration-data-to-vms/
Best,
On Mon, 14 Jun 2021 at 21:57, Felipe wrote:
> Hello everyone!!!
>
> I wonder if it is possible to change the boot order on xenserver?
>
> in
Hello everyone!!!
I wonder if it is possible to change the boot order on xenserver?
in global settings, is it at
allow.additional.vm.configuration.list.xenserver?
i would like to put DVD first in boot order.
thank you all!!
[image: image.png]
4 juil. 2020 à 04:34, David Merrill
> a
> écrit :
>
> > Reporting in on this - turns out was fairly painless (I never ended
> up
> > goofing around with host tags at all).
> >
> >
> >
> > Here's an updated to-do list (with some observations):
l).
>
>
>
> Here's an updated to-do list (with some observations):
>
>
>
> 1. In XenCenter – if HA is enabled for the XenServer pool, disable it
> 2. Stop ACS management/usage services
> 3. Do MySQL database backups
ions):
>
>
>
> 1. In XenCenter – if HA is enabled for the XenServer pool, disable it
> 2. Stop ACS management/usage services
> 3. Do MySQL database backups
> 4. Start ACS management/usage services
> 5. Start with the pool master
> * In ACS – Put the pool
Hey Andrija,
It worked. Now after clearing the below params from XenServer host and
restarting the management services, it has copied all directory and plugins to
XenServer hosts and now all XenServer hosts are showing in “UP” State. Thanks
for the help.
Vivek Kumar
Manager - Cloud & De
restart your network with "clean up" option checked?
> >
> >
> > El lun, 22 feb 2021 a las 17:27, Vivek Kumar
> > ( vivek.ku...@indiqus.com.invalid>>) escribió:
> >
> >> Hello Team,
> >>
> >> Recently, I have upgraded t
rk with "clean up" option checked?
>
>
> El lun, 22 feb 2021 a las 17:27, Vivek Kumar
> (mailto:vivek.ku...@indiqus.com.invalid>>)
> escribió:
>
>> Hello Team,
>>
>> Recently, I have upgraded the XenServer pool from 7.0 to XenServer 7.1
>&
Hello Vivek,
Did you try to restart your network with "clean up" option checked?
El lun, 22 feb 2021 a las 17:27, Vivek Kumar
() escribió:
> Hello Team,
>
> Recently, I have upgraded the XenServer pool from 7.0 to XenServer 7.1
> under ACS 4.15. After that I’m unable to
Hello Team,
Recently, I have upgraded the XenServer pool from 7.0 to XenServer 7.1 under
ACS 4.15. After that I’m unable to start any router. It’s giving below error.
2021-02-23 01:53:07,661 DEBUG [c.c.h.x.r.CitrixResourceBase]
(DirectAgent-132:ctx-b70f66c3) (logid:9f07ddd0) Creating VIF
Hi Ammad,
Adding guest mapping alone might not work as the product name has been changed
by Citrix and Xenserver is now Citrix Hypervisor. This will create an issue
while trying to add the host or with some operations. To support this product
name change, updates have been made in CloudStack
Hi,
I am currently running ACS4.11.3 and Xenserver 7.0. Is it possible that I
could manually add guest OS mapping for ubuntu 18 / 20 and win server 2019
for xenserver 8.2 with API addGuestOsMapping
<https://cloudstack.apache.org/api/apidocs-4.11/apis/addGuestOsMapping.html>.
Will i
Reporting in on this - turns out was fairly painless (I never ended up goofing
around with host tags at all).
Here's an updated to-do list (with some observations):
1. In XenCenter – if HA is enabled for the XenServer pool, disable it
2. Stop ACS management/usage services
3. Do
Andrija,
I appreciate you sharing your thoughts on this. I'm getting my ducks in a row
on the XenServer side (for the upgrade) & I'll give the plan a go.
I'll report in afterwards, wish me luck!
Thanks,
David
David Merrill
Senior Systems Engineer,
Managed and Private/Hybrid Cloud Serv
a master, your steps look fine.
For the records, I've updated& the official documentation, for
XenServer 6.5+ : https://github.com/apache/cloudstack-documentation/pull/140
/
https://acs-www.shapeblue.com/docs/WIP-PROOFING/pr140/installguide/hypervisor/xenserver.html#upgrading-xenserver-vers
Hi All,
I have a production deployment of ACS managing three XenServer Clusters
(XenServer pools of 6 hosts each) in two different Zones. I now find myself in
the position of needing to do a major version upgrade of those hosts. Happily I
have a ACS lab managing a XenServer cluster running
http://docs.cloudstack.apache.org/en/latest/releasenotes/compat.html
cheers
On Tue, 26 May 2020 at 19:08, Luis Martinez
wrote:
> Hi
>
> ACS website is not loading for me, I am trying to find what versions of
> XenServer/XCP-NG are supported.
>
> Thank you
>
>
--
Andrija Panić
Hi
ACS website is not loading for me, I am trying to find what versions of
XenServer/XCP-NG are supported.
Thank you
Hello All
I plan to use vgpu in passhrough mode in xenserver.
I found in the code that the method of createVGPU is only rewritten in the of
XenServer620SP1Resources.
Does xenserver only support vgpu use under 6.2sp1 version?
CloudStack 4.13.0
-Jerry
Felipe,
I suggest you download the VHD from CloudStack and use external tools like
qemu-img to convert from VHD to QCOW2. You will need to uninstall the XenServer
tools and install the KVM one.
Marco
Rua Gomes de Carvalho, 911 – Sala 316
Vila Olímpia, São Paulo, SP, Brasil, 04547-003
Phone
Hi All,
We deploy new zone on ACS but we need migrate old Zone that are running
with XenServer to new Zone with KVM hypervisor.
I would like know if some one have solution for this situation.
Att / Regards
Felipe Rossi | BRASCLOUD
Founder - Diretor de Negócios e Inovação
Cloud Architect
fel
This is a XenServer-specific technique - it relies on removing a Tag from
XenServer, not to be confused with the host tags in ACS. KVM hosts in ACS
do not use the same setup procedure as XenServer Hosts.
On Mon, 25 Nov 2019 at 12:58, Michael Kesper wrote:
> Hi all,
>
> On 25.11
f the other ACS modifications to a XenServer HV.
The only thing that (sadly) can not be set by this method seem to be host tags,
a cs_host API call is needed for that (at least CS4.9 and KVM).
Best wishes
Michael
signature.asc
Description: OpenPGP digital signature
restart the management server. When it connects to that host,
it will perform the initial setup procedures again.
We use this procedure to roll out a customised SystemVM ISO, but it should
also take care of the other ACS modifications to a XenServer HV.
Regards,
Richard
On Mon, 25 Nov 2019 at 01:43
filesystem!
Put host in maintenance mode in ACS - this will live migrate away all VMs,
so the host is empty.
Put the host in maintenance mode itself (XenServer or via XenCenter)
Reboot, boot from new ISO/CD, upgrade XS, boot into the new OS, exit
Maintenance mode in XenCenter/XenServer only.
Now the fun
Hi Melanie,
I would without a doubt choose Linux bridge unless you want to use some
very special things that OVS provides - but assuming you'll be using VLANs
(or VXLANs) and considering the simplicity, stability, performance - I
would go with that.
Since XenServer is using it as the default
Hi Andrija,
Am Donnerstag, den 15.08.2019, 12:54 +0200 schrieb Andrija Panic:
> One question though, why are you aiming to use OVS for KVM? i.e. why
> not regular/default Linux bridge?
I am more familiar with OpenVSwitch and I did have the impression that
is gives more configuration options for
to change anything with XenServer now
and I support ditching it for KVM (my personal attitude...)
After you have prepared all the bridges/OpenVSwitches, just edit each of
the 4 Traffic types, to set "KVM Traffic Lable" to have the value as the
name of bridge / OpenvSwitch that will carry
t up for one zone and what that
would mean.
> b) are you planning on reconfiguring your XenServer hosts at all (in
> sense
> of networking) or just thinking adding KVM hosts and defining proper
> KMV
> Traffic Label for each traffic type you have?
Would it be possible to reconfigure
Hi Melanie,
a) I assume you are planning on staying on single "Physical network" in ACS?
b) are you planning on reconfiguring your XenServer hosts at all (in sense
of networking) or just thinking adding KVM hosts and defining proper KMV
Traffic Label for each traffic type you have?
M
Hello,
we plan to change from XenServer to KVM virtualisation for Apache
CloudStack 4.11 with advanced networking.
I am currently installing an KVM proof of concept und would like to
integrate two KVM hosts for testing as a new cluster to CloudStack.
I got some questions concerning
Hello all
My ACS 4.11.3+ xenserver 7.1.3 +iscsi shared storage.
We plan to add multiple SSD hard drives to each HOST, and each SSD hard drive
is made into an SR. These SRs are added to the ACS for local storage.
Proceed as follows :
1, create an SR of the SSD disk
2, add a record
I encountered this problem and my solution was to add 7.1.2 support manually.
INSERT IGNORE INTO `cloud'. `guest_os_hypervisor'(uuid, hypervisor_type,
hypervisor_version, guest_os_name, guest_os_id, created, is_user_defined)
SELECT UUID (), `Xenserver', `7.1.2', guest_os_name, guest_os_id
I've just run up a clean instance of CloudStack 4.11.2 against 2
XenServer 7.1 CU2 Hosts (running in VMs). I was unable to get the VMs
to boot, with errors about HVM required. I spotted the log message
"no guest OS type, start it as HVM guest", which indicates that Xen is
being t
Hi All
I take over XenServer 7.1.2 through cloudstack (4.11.2). In order to realize HA
of VM and HOST, I open HA on XENSERVER (all VM select "Dot not restart").
ISO NFS SR (i-2-43-VM-ISO) cannot be deleted after VM unloads ISO after HA is
turned on. Once the same ISO is mou
Hi Yiping,
Please check how this was done in previous releases (i.e. added support for
XenServer 7.1.0 and some additional missing guest os mapping etc:
https://github.com/apache/cloudstack/blob/master/engine/schema/src/main/resources/META-INF/db/schema-41000to41100.sql
Just make sure
Hi, Andrija:
I am willing to try this approach given that we are working in a lab
environment. Otherwise we would have to downgrade to use XenServer 7.1 +
installing security patches afterwards
Since we also need to add one new entry in hypervisor_capabilities table for
XenServer 7.1.1
Street, London WC2E 9DPUK
@shapeblue
-Original Message-
From: Yiping Zhang
Sent: 29 January 2019 21:54
To: users@cloudstack.apache.org
Subject: Re: how to run rhel 6.x VM as PV VM on xenserver 7.1CU1?
Hi, Andrija:
I think you are
on to something here:
Here are my query
+
| id | name | hypervisor_type | hypervisor_version |
++---+-++
| 56 | lab-hv03 | XenServer | 7.1.1 |
| 57 | lab-hv02 | XenServer | 7.1.1 |
| 58 | lab-hv04 | XenServer
n reported for your XenServer, I'm assuming it might report
true version after upgrade i.e. "7.1.2", for which there are NO mappings inside
guest_os_hypervisor table - if so, you would need to duplicate all the mapping
records for XenServer 7.1.0 (or 7.0.0).
Different way to sa
Additionally, I expect that following table is correct in sense of paper vs
reality, but always good to check:
https://docs.citrix.com/en-us/xenserver/7-1/system-requirements/guest-os-support.html
andrija.pa...@shapeblue.com
www.shapeblue.com
Amadeus House, Floral Street, London WC2E 9DPUK
Hi Yiping,
If you do the following SQL:SELECT * FROM guest_os_hypervisor WHERE
hypervisor_type="XenServer" and hypervisor_version="7.1.0" AND guest_os_id IN
(SELECT id FROM guest_os WHERE display_name="CentOS 6.4 (64-bit)");
+--
Hello Meanie,
That is true. XenServer does not support IOPS per volume. I did asked
Citrix about a year ago about that. With the recent new features regarding
storage (thin provisioning over shared block devices!) I really hope they will
continue they focus on storage with the next
/QA:Testcase_Virtualization_IO_Throttling
Cheers
Andrija
On Mon, 26 Nov 2018 at 14:28, Melanie Desaive
wrote:
> Hi all,
>
> do I get it right, that there is no way to limit IOPS per volume with
> XenServer as hypervisor? (Using ACS 4.11)
>
> I tried the settings to limit IO bandwidth a
Hi all,
do I get it right, that there is no way to limit IOPS per volume with
XenServer as hypervisor? (Using ACS 4.11)
I tried the settings to limit IO bandwidth and IOPS per volume on
hypervisor side with XenServer and only the bandwidth limitation seems
to have an effect. Seems to me
Please excuse my post.
I think I found the issue. I have deployed cloudstack 4.9 instead of 4.11.
Best regards,
Jordan
From: Yordan Kostov
Sent: Tuesday, August 21, 2018 12:04 PM
To: users@cloudstack.apache.org
Subject: Secondary storage issue with XenServer
Hello everyone,
I
Hello everyone,
I recently found about Cloudstack and decided to give it a try
and I really like it so far but I bumped into a very weird config issue.
Here is my test environment.
10.10.10.200 - XenServer 7.1 host (all free patches installed
To: users@cloudstack.apache.org
Subject: RE: Cloudstack 4.11.1 RC1. SystemVM Config Issue with Xenserver 7.1.
Detected as xen-domU.
Hi James,
This looks like a slightly different issue as the system VM is not getting it’s
config when booting. Can you look at the system VM through XenCenter, and look
Angus
From: James Richards
Sent: 01 June 2018 13:01
To: users@cloudstack.apache.org
Subject: Cloudstack 4.11.1 RC1. SystemVM Config Issue with Xenserver 7.1.
Detected as xen-domU.
Hi
I’m attempting to integrate Cloudstack on top of Centos 7, with Xenserver 7.1
as the hypervisor.
Initially I
Hi
I’m attempting to integrate Cloudstack on top of Centos 7, with Xenserver 7.1
as the hypervisor.
Initially I came up against the problem described here,
https://github.com/apache/cloudstack/issues/2561 . The SystemVM’s did not
complete configuration, with the ‘systemvm type=’ observed
Envoyé : vendredi 27 avril 2018 10:18
À : Cloudstack Mailinglist <users@cloudstack.apache.org>
Objet : KVM in Xenserver advanced networking environement
Hi together,
currently we have a cloudstack 4.10 environment with Xenserver and the
following network configuration:
Physical (Bond)
7, "Benjamin Naber" <benjamin.na...@coders-area.de> wrote:
Hi together,
currently we have a cloudstack 4.10 environment with Xenserver and the
following network configuration:
Physical (Bond) Interfaces:
1 management -> untagged vlan f
Hi together,
currently we have a cloudstack 4.10 environment with Xenserver and the
following network configuration:
Physical (Bond) Interfaces:
1 management -> untagged vlan for management / tagged vlan 133 for secondary
storage.
2 guest -> tagged vlans 2000-2699
3 public -> tagged
After more investigation, I found out that changing template's "OS Type"
assignment affects how a VM is started as PV or HVM guest on either XenServer
6.5 or 7.0 clusters:
On XenServer 6.5 clusters, 64 bit RHEL guests with versions up to 6.7 (last
6.x version listed by A
Hi Yiping,
Am 11.04.2018 um 23:30 schrieb Yiping Zhang:
>
> Why does CloudStack convert just a few rhel 6.x instances into HVM mode,
> while leaving most in PV mode?
> How would I force them back to PV guests?
To my understanding CloudStacks decides about the virtualiuzation mode
of a VM
Hi, list:
I am in the process of upgrading my hypervisors clusters from XenServer 6.5 to
7.0 for all my ACS instances.
My XS 7.0 clusters are patched up to XS70E050.
During cluster rolling upgrade, VM instances are live migrated several times,
eventually all of them running on XS 7.0 hosts
[mailto:m...@swen.io]
Gesendet: Dienstag, 10. April 2018 09:29
An: users@cloudstack.apache.org
Betreff: XenServer Storage Live Migration between pools
Hi all,
we added a new XenServer 6.5 SP1 cluster (pool) to our CS installation. When
we do a live migration between pools we run into a problem
Hi all,
we added a new XenServer 6.5 SP1 cluster (pool) to our CS installation. When
we do a live migration between pools we run into a problem with the VM. The
migration itself is working fine and the VM is reachable all the time. I can
see in XenCenter that the same network has been created
9:14:00 PM
Subject: Re: upgraded XenServer host stays in Alert state
Hi, Kristian:
Thanks for the link. I have checked it out , but its contents are quite dated,
even though the link itself implies it is for ACS 4.11.
In the doc, there is no mentioning if it covers the case of upgrading from
XenServ
XenServer 7.0
installation ISO) and now both Xen pool and ACS are happy. I'll leave this
cluster alone till after the release frenzy is over!
But seriously, I still would like to know what went wrong this time. I have
built two brand new XenServer 7.0 clusters and upgraded another two clusters
reluctant to
follow it as is. Besides, I have upgraded two separate XenServer clusters
already without any issues by following my current own process so far,
including one cluster on current ACS instance.
Yiping
On 3/27/18, 12:37 AM, "Kristian Liivak" <k...@wavecom.ee> wrote:
Hi Yiping,
If I remember correctly a full ISO upgrade of a XenServer actually backs up the
existing version (OS partition), then installs a brand new XS version on top
before copying settings across from the backup. As a result you are effectively
looking at more or less a new install
quot; <yzh...@marketo.com>
To: "users" <users@cloudstack.apache.org>
Sent: Monday, March 26, 2018 11:47:24 PM
Subject: upgraded XenServer host stays in Alert state
Hi, all:
I am upgrading my ACS clusters from XenServer 6.5 to XenServer 7.0. I am on
ACS version 4.9.3.0. On t
Hi, all:
I am upgrading my ACS clusters from XenServer 6.5 to XenServer 7.0. I am on
ACS version 4.9.3.0. On this ACS instance, I have another fully functioning
XenServer 7.0 cluster already.
This time, after I upgraded the pool master, it remains in “Alert” state, while
all the slave
attaching DATA volume to VM), after
> certain time around 37670 seconds.
>
> Version of:
> - CloudStack is 4.5.0
> - XenServer 6.5.0
> - MySQL 5.1.73
>
>
> The error and log is provided below, Could someone please assist me here
.lakin...@gmail.com
> wrote:
> Hi All,
>
> I'm facing issue when copying larger size volumes. i.e., Secondary
> Storage to Primary Storage (I mean attaching DATA volume to VM), after
> certain time around 37670 seconds.
>
> Version of:
> - CloudStack is 4.5.0
> - XenServ
ry Storage (I mean attaching DATA volume to VM), after
> certain time around 37670 seconds.
>
> Version of:
> - CloudStack is 4.5.0
> - XenServer 6.5.0
> - MySQL 5.1.73
>
>
> The error and log is provided below, Could someone please assist me here
> which steps i have to ta
Hi All,
I'm facing issue when copying larger size volumes. i.e., Secondary Storage
to Primary Storage (I mean attaching DATA volume to VM), after certain time
around 37670 seconds.
Version of:
- CloudStack is 4.5.0
- XenServer 6.5.0
- MySQL 5.1.73
The error and log is provided below, Could
]
Gesendet: Samstag, 3. Februar 2018 12:41
An: users@cloudstack.apache.org; S. Brüseke - proIO GmbH <s.brues...@proio.com>
Betreff: Re: XenServer Licensing Change - Switch Hypervisors?
We too was evaluating ScaleIO on XS, now we move to KVM or Hyper-V but always
with ScaleIO, I don't understan
tion with using XenServer 6.5. Besides it will not
> be patched XS6.5 has poor memory performance. We are in the middle of
> evaluating KVM with ScaleIO to get rid of XenServer in the near future. I
> am stuck right now on how to mount a ScaleIO volume do a KVM host.
> Migrate all VM
Hi Alessandro,
we are in the same situation with using XenServer 6.5. Besides it will not be
patched XS6.5 has poor memory performance. We are in the middle of evaluating
KVM with ScaleIO to get rid of XenServer in the near future. I am stuck right
now on how to mount a ScaleIO volume do a KVM
gt;
> That's an interesting answer to recent citrix licensing change for
> xenserver, I'll definitely keep an eye on this project!
>
> thanks!
>
>
> *Pierre-Luc DION*
> Architecte de Solution Cloud | Cloud Solutions Architect
> t 855.652.5683
>
> *CloudOps* Votre parten
Hi Dingo,
That's an interesting answer to recent citrix licensing change for
xenserver, I'll definitely keep an eye on this project!
thanks!
*Pierre-Luc DION*
Architecte de Solution Cloud | Cloud Solutions Architect
t 855.652.5683
*CloudOps* Votre partenaire infonuagique* | *Cloud Solutions
- Original Message -
> From: "Sean Lair" <sl...@ippathways.com>
> To: "users" <users@cloudstack.apache.org>
> Sent: Sunday, 7 January, 2018 18:20:11
> Subject: RE: XenServer Licensing Change - Switch Hypervisors?
> Thanks for the reply Nux, yea
Thanks for the reply Nux, yea we originally chose XenServer over KVM because
KVM didn't support all of the VM snapshot functionality of XenServer.
We are evaluating switching to KVM now... But don't have a good way of moving
customers over from XenServer host to KVM hosts...
We
1 - 100 of 1242 matches
Mail list logo
