Hello all,

Trem Williams sent me this message so I could review it for
compliance with the non-commercial nature of the list. It's just fine
by me, and I am forwarding it to you all because it is good info. 

Constant current has been discussed and is thought to be among the 
best techniques we know about. But it hasn't been discussed a lot 
recently and it is good to get another developer's point of view. 
Thanks for good citizenship and for sharing your results, Trem.

Be well,

Mike D.

>>>>>>>>>>>>Begin included message

Hello All,

I have to jump in and pass on some information we have regarding
voltage, current density, current flow, timing, water temperature,
electrode spacing, electrode immersion depth and electrode
deterioration.

We use 1/4" wide by 5" long silver electrodes with our colloid
generators. This results in quite a large surface area of silver. 
Immersion depth is about 3 inches, typically.  Our generators limit
the current with a regulator to a constant, low current value so as to
get very low current density.  We do not get any bubbling, boiling or
any odd looking effects. Just a slow release of silver into the water.

Our instructions are to not use saline, do not heat the water, use
steam distilled water and place the electrodes at least two inches
apart.  Nothing critical there.  We suggest running the unit for 4-5
hours in 16 ounces of water to get 15-20 PPM.  As you can see, our
generators take quite some time to make a batch but what is a little
extra time when the results are always the same.

We are able to get repeatable results every time a batch is made.  All
the variables are taken care of by using the constant current
regulator. Spacing and water temperature are not part of the equation.
 All one has to do is use the same amount of distilled water and run
the generator for the same time to get the same results each time. 
It's a no brainer.  The key here is CONSTANT CURRENT.

As far as I'm concerned, using a constant voltage source is the same
as trying to drive a car with the gas pedal stuck to the floor.  The
speed is going to continue to increase until the engine is turned off.
 The same analogy applies to using constant voltage.  Wire spacing,
size, depth of immersion and water temperature are the  variables and
when the silver starts to build up in the water, the current starts to
run away and increase too rapidly.  That's why it bubbles, makes black
particles, gets brown, etc. And it is almost never repeatable.  There
are too many variables in the process using a constant voltage source.

If one wants to do it inexpensively without using electronic circuitry
to make it automatic, try using a rheostat and milliameter in series
with the battery and electrodes.  These are available at Radio Shack
or any electronic parts store.  After the current starts to flow,
adjust the rheostat to maintain current at some low value.  In our
case we adjust the internal regulator so that it maintains a constant
current flow of 1 milliampere.  I would suggest that value for the
do-it-yourselfers if they use electrodes with equivalent surface area
to our electrodes.  If using wire, the surface area will be less and
the current density will be higher so I can't suggest what current to
use.  I would suggest a lower value.

It is our experience that the electrodes will last upwards of 700-1000
hours if they are reversed every once in a while.   It is also our
experience that there is little or no sludge or fallout using this
technique.  Particle size is small as attested to by consistently
clear colloidal water without any "sparklers" when a laser is shone
through the water.  The color is golden and depth of color is
determined by length of running time.  It is never cloudy; always
clear.  It is never brown, purple, blue or red.  Just light golden,
clear water.

The upshot is; use more silver surface area and limit the current and
you will get repeatability.  And that's what we're all after isn't it;
a uniform product?

Good luck to all.


Trem Williams
www.silvergen.com

-----Original Message-----
From: Pam Whitmire <[email protected]>
To: [email protected] <[email protected]>
Date: Monday, June 28, 1999 8:15 PM
Subject: CS strength, times, etc.


>Ok, I'm confused. Someone told me that you don't WANT to see your silver
>wires bubbling and misting. And NOT to use saline. When I used saline, I
>saw lots of mist rising off one of the wires (I'm using a small
>generator with 3 9volt batteries) and the solution stayed sort of misty.
>Tasted just like the gold-colored CS that I had bought from a company.
>When I didn't use saline, I didn't see anything at all happening. Does
>it take a lot of time? One article said DONT boil the water - another
>said DO boil it. Today I heated the water to approx. 125 degrees,
>started the generator and at about 11 minutes I began to see tiny
>bubbles on one rod. Started timer again, and at the end of about 24
>minutes the one rod was black and starting to form some deposits on the
>end (but none were dropping in the water) the other rod was also
>blackish and beginning to mist a bit from the end. I turned it off and
>have left it alone. How do I know it's correct? Do you just assume that
>you got a good solution because you had the water, silver, generator and
>left it for x amount of time? I know I sound like a real dummy, but I
>really want this to work for me. I appreciate all of you who have taken
>time to answer me....feel free to reply to me personally if that is
>best. Thanks in advance,
>Pam


--
The silver-list is a moderated forum for discussion of colloidal silver.

To join or quit silver-list or silver-digest send an e-mail message to: 
[email protected]  -or-  [email protected]
with the word subscribe or unsubscribe in the SUBJECT line.

To post, address your message to: [email protected]

List maintainer: Mike Devour <[email protected]>