Trem:

I like your approach to generating CS using a current regulated (1 ma) power
supply. With this approach the only variables are time, and water quality. I
wonder how this approach applies to the HVAC method. Is it needed or even
possible to implement a 10,000 VAC or DC current limited generator?

Dennis Lipter

"M. G. Devour" wrote:

> Hello all,
>
> Trem Williams sent me this message so I could review it for
> compliance with the non-commercial nature of the list. It's just fine
> by me, and I am forwarding it to you all because it is good info.
>
> Constant current has been discussed and is thought to be among the
> best techniques we know about. But it hasn't been discussed a lot
> recently and it is good to get another developer's point of view.
> Thanks for good citizenship and for sharing your results, Trem.
>
> Be well,
>
> Mike D.
>
> >>>>>>>>>>>>Begin included message
>
> Hello All,
>
> I have to jump in and pass on some information we have regarding
> voltage, current density, current flow, timing, water temperature,
> electrode spacing, electrode immersion depth and electrode
> deterioration.
>
> We use 1/4" wide by 5" long silver electrodes with our colloid
> generators. This results in quite a large surface area of silver.
> Immersion depth is about 3 inches, typically.  Our generators limit
> the current with a regulator to a constant, low current value so as to
> get very low current density.  We do not get any bubbling, boiling or
> any odd looking effects. Just a slow release of silver into the water.
>
> Our instructions are to not use saline, do not heat the water, use
> steam distilled water and place the electrodes at least two inches
> apart.  Nothing critical there.  We suggest running the unit for 4-5
> hours in 16 ounces of water to get 15-20 PPM.  As you can see, our
> generators take quite some time to make a batch but what is a little
> extra time when the results are always the same.
>
> We are able to get repeatable results every time a batch is made.  All
> the variables are taken care of by using the constant current
> regulator. Spacing and water temperature are not part of the equation.
>  All one has to do is use the same amount of distilled water and run
> the generator for the same time to get the same results each time.
> It's a no brainer.  The key here is CONSTANT CURRENT.
>
> As far as I'm concerned, using a constant voltage source is the same
> as trying to drive a car with the gas pedal stuck to the floor.  The
> speed is going to continue to increase until the engine is turned off.
>  The same analogy applies to using constant voltage.  Wire spacing,
> size, depth of immersion and water temperature are the  variables and
> when the silver starts to build up in the water, the current starts to
> run away and increase too rapidly.  That's why it bubbles, makes black
> particles, gets brown, etc. And it is almost never repeatable.  There
> are too many variables in the process using a constant voltage source.
>
> If one wants to do it inexpensively without using electronic circuitry
> to make it automatic, try using a rheostat and milliameter in series
> with the battery and electrodes.  These are available at Radio Shack
> or any electronic parts store.  After the current starts to flow,
> adjust the rheostat to maintain current at some low value.  In our
> case we adjust the internal regulator so that it maintains a constant
> current flow of 1 milliampere.  I would suggest that value for the
> do-it-yourselfers if they use electrodes with equivalent surface area
> to our electrodes.  If using wire, the surface area will be less and
> the current density will be higher so I can't suggest what current to
> use.  I would suggest a lower value.
>
> It is our experience that the electrodes will last upwards of 700-1000
> hours if they are reversed every once in a while.   It is also our
> experience that there is little or no sludge or fallout using this
> technique.  Particle size is small as attested to by consistently
> clear colloidal water without any "sparklers" when a laser is shone
> through the water.  The color is golden and depth of color is
> determined by length of running time.  It is never cloudy; always
> clear.  It is never brown, purple, blue or red.  Just light golden,
> clear water.
>
> The upshot is; use more silver surface area and limit the current and
> you will get repeatability.  And that's what we're all after isn't it;
> a uniform product?
>
> Good luck to all.
>
> Trem Williams
> www.silvergen.com
>
> -----Original Message-----
> From: Pam Whitmire <[email protected]>
> To: [email protected] <[email protected]>
> Date: Monday, June 28, 1999 8:15 PM
> Subject: CS strength, times, etc.
>
> >Ok, I'm confused. Someone told me that you don't WANT to see your silver
> >wires bubbling and misting. And NOT to use saline. When I used saline, I
> >saw lots of mist rising off one of the wires (I'm using a small
> >generator with 3 9volt batteries) and the solution stayed sort of misty.
> >Tasted just like the gold-colored CS that I had bought from a company.
> >When I didn't use saline, I didn't see anything at all happening. Does
> >it take a lot of time? One article said DONT boil the water - another
> >said DO boil it. Today I heated the water to approx. 125 degrees,
> >started the generator and at about 11 minutes I began to see tiny
> >bubbles on one rod. Started timer again, and at the end of about 24
> >minutes the one rod was black and starting to form some deposits on the
> >end (but none were dropping in the water) the other rod was also
> >blackish and beginning to mist a bit from the end. I turned it off and
> >have left it alone. How do I know it's correct? Do you just assume that
> >you got a good solution because you had the water, silver, generator and
> >left it for x amount of time? I know I sound like a real dummy, but I
> >really want this to work for me. I appreciate all of you who have taken
> >time to answer me....feel free to reply to me personally if that is
> >best. Thanks in advance,
> >Pam
>
> --
> The silver-list is a moderated forum for discussion of colloidal silver.
>
> To join or quit silver-list or silver-digest send an e-mail message to:
> [email protected]  -or-  [email protected]
> with the word subscribe or unsubscribe in the SUBJECT line.
>
> To post, address your message to: [email protected]
>
> List maintainer: Mike Devour <[email protected]>


--
The silver-list is a moderated forum for discussion of colloidal silver.

To join or quit silver-list or silver-digest send an e-mail message to: 
[email protected]  -or-  [email protected]
with the word subscribe or unsubscribe in the SUBJECT line.

To post, address your message to: [email protected]

List maintainer: Mike Devour <[email protected]>