Thanks Mike, It could be that the water is super pure, as I first filter, then distill the water. After reading and hearing of all the stuff that "can" be found in water, I'm not taking any more risks of taking something in I don't want in my organism. :-) I'll leave a bit of "old brew" in the jar for the next batch. How much would make the difference, and how long should it take? 3-4 hours? instead of the 6+?
I remember reading a few posts about seeding, but it seems that it didn't make a difference for some, so I wonder what it all depends on. I would feel more sure of myself if I could test the ppm of the water in between, as to see if I could cut off the electricity, and so, also see how accurate (or not), the little green light is. Aldi On Mon, Mar 1, 2010 at 1:47 PM, M. G. Devour <mdev...@eskimo.com> wrote: > Aldi writes: > > See, I have never yet made any under 6 hours, thats for sure. Can't > figure > > out why. Like I mentioned before, a few batches ago, I had to cut the > > brewing, cause it was going on 14 hours. > > I suppose if your water happens to be very pure it could slow down the > early, "seeding" part of the process considerably. Leaving a little bit > of the previous batch in the jar would probably even that out > considerably. > > It also sounds like Pat ought to cut back on the "ppm" setting to below > the point at which it generates significant "crud." When you get that, > it just means you've gone too long, and whatever silver you've added in > the later phase of the run has gone straight to large particles that > don't enhance things much and waste electrodes. > > Even if the instructions say to run higher, it could be that Pat's > particular unit needs to be run at a lower setting. > > Be well, > > Mike D. > > > On Fri, Feb 26, 2010 at 10:29 PM, MaryAnn Helland > > <marmar...@bellsouth.net>wrote: > > > > > That's really odd, Pat. Mine rarely takes more than 5 or 6 hours. My > CS > > > is always clear, and I never have any crud on the bottom of my jars. > > > > ------------------------------ > > > *From:* Pat <pattycake29...@yahoo.com> > > > > My Colloid Master AC has a green light that goes on and off while > brewing, > > > then turns off totally when it's finished. The red light stays on to > > > indicate it has power plugged in (although I think it goes on and off, > too > > > during brewing.) Sometimes it takes 12 hours or more. I keep it in > the > > > dining room, so don't look at it often. It leaves quite a bit of crud > on > > > the bottom of my jars. The CS is clear as long as I don't go above > 5.5. > > > The worst thing about the machine is that it's hard sometimes to get > the > > > electrodes straight and parallel when I'm putting the clips on. It > eats > > > them up, too, sometimes. I'm on the third set in four years and I > don't > > > make it very often. > > > > ________________________________ > > > From: Golden Aldi <goldena...@gmail.com> > > > My setting is at about 5.5 or 6 to get a 10 ppm. I can't tell if it > shuts > > > itself off or not, but I'm hoping it does, and its the other light, the > red > > > one, that doesn't go on when it stops, which it should, according to > the > > > instructions that came with the generator. If the generator does go > off, > > > then maybe completely, which would explain why the red light does not > go on. > > > *grin* > > [Mike Devour, Citizen, Patriot, Libertarian] > [mdev...@eskimo.com ] > [Speaking only for myself... ] > > > -- > The Silver List is a moderated forum for discussing Colloidal Silver. > Rules and Instructions: http://www.silverlist.org > > Unsubscribe: > <mailto:silver-list-requ...@eskimo.com?subject=unsubscribe> > Archives: > http://www.mail-archive.com/silver-list@eskimo.com/maillist.html > > Off-Topic discussions: <mailto:silver-off-topic-l...@eskimo.com> > List Owner: Mike Devour <mailto:mdev...@eskimo.com> > > >