Salt is what produces the corrosive chemicals [hypochlorous acid and
sodium hydroxide]...and that's the whole reason to use a zapper [change the
PH of the blood in a localized area]
Try eliminating the salt in your blood.
The problem is that blood flow in the skin is not sufficient to reduce the
concentration of corrosive chemicals being made out of the salt in the
blood ..and/or being used as an electrolyte....at the given rate
Gotta slow it down, spread it out or give it time to dilute with the blood
flow rate available before it becomes concentrated enough to burn the skin.
Ode
At 11:40 AM 12/27/2012 -0500, you wrote:
I believe this is a correct analysis. It might be worth while figuring
out something that can be added to the water that will increase
conductivity and not produce such corrosive chemicals. Any salt, acid or
alkaline will work. I was thinking of either vinegar (acetic acid) or
citric acid. I believe that hydrogen will be released at one electrode
and CO2 at the other. The CO2 is probably not a problem, it will make
carbonic acid, but the hydrogen will quickly react with most metals making
a metal hydride. So the choice of electrode material will be important.
I am looking at the pads on a TENS unit. They appear to have a carbon
conductive layer, and you use some type of gel with it. Carbon would be a
good choice if made like they are in the TENS unit.
Marshall
On 12/27/2012 8:37 AM, Ode Coyote wrote:
The problem is that the electrochemicals being produced build up in the
skin because the skin doesn't have much blood flow rate to dilute them as
fast as they are being made.
Those are "chemical" burns.
5 ways to prevent..can all be used at once or any in part.
Reduce voltage [potentiometer]
Reduce electrolyte conductivity..ie dilute it with more water [does the
same thing as the pot, but in a different spot]
Increase electrode pad area to spread concentration of electro chemicals
over a larger volume of blood flow.
Use zapper for a few minutes and take a few off.
Switch polarity to neutralize that particular electro-chemical with it's
opposite.
Ode
If one applies a DC current to a bucket of salt water, it will split into
Hypochlorous Acid and Sodium Hydroxide.[ an alkaline base...aka LYE ]
That substance was being promoted as a super duper house hold
cleaner...with a very short shelf life.
The Hypochlorous Acid is a grand disinfectant.
The Sodium Hydroxide, a great de-greaser [like Formula 409 ]
Then, there is MMS [ "Miracle Mineral Supplement"...which looks like
everything BUT that, having nothing to to with supplementing minerals ]
made from Sodium Chlorite being used to get rid of parasites and germs in
the blood stream..easy enough to over dose on and make you feel really
ill. [Careful there]
THEN..there is the Godzilla Zapper, a very simple and cheap device that
can be made using junk around the house...used for "blood electrification".
<http://health.groups.yahoo.com/group/microelectricitygermkiller/>http://health.groups.yahoo.com/group/microelectricitygermkiller/
BUT
Electricity doesn't flow through a conductive liquid like it would a
metal wire, it transports electrons via chemical reactions
....."Electro-chemistry"
SO
The Zapper cannot be working by the method claimed...but there is much
that indicates that it does work.
How could that be?!!!
OK
So what is the human body but a bag of salt water ? [rather than a bucket
of salt water]
If one electrode is Alkalizing and the other is Acidifying and you get
salt when the two chemicals meet up and recombine, what could that
potential be used for?
1] You have a MMS analog with it's own antidote being produced in vivo
using a simple Zapper. [ A couple of AA batteries, some wire and a couple
of sponges soaked with salt water]
....too much? [burning and itching??]
Turn it down or shut it off. [let the build up dissipate]
2] You have an Alkaline situation at the OTHER electrode being made in
vivo ....with ITs antidote lurking just around the bend......
Both made from existing salt, going back to salt.
That's chemo therapy with immediate dosage control and location control
as well...and no toxins left over after recombination.
At 11:58 AM 12/26/2012 -0800, you wrote:
Hi,
Although I wrapped the copper handholds in a layer of wet paper towel I
ended up with a burn on the side on which I felt the estim most. I'm
used to working with units that have an amplitude adjustment and this
zapper does not. I was running 15 Hz.
Would someone tell me what I can do to avoid this happening again. It
happened once before so I know from experience that they take awhile to heal.
Thanks.
PT
No virus found in this message.
Checked by AVG - <http://www.avg.com>www.avg.com
Version: 10.0.1430 / Virus Database: 2637/5490 - Release Date: 12/27/12
