Hi Gaston,
There's more than one way to increase your starting current. I use a ten inch
electrode, it goes down 4", 2" across, and 4" back up, it's U shaped and I get
about 9-9.5 inches immersed in the DW.  My starting current jumped from
0.23-0.35 to about 0.65-.85 with this method, and the time to cook a batch
dropped dramaticaly also.  I made it out of 14ga wire. I do have 6 feet of 12
ga wire that just arrived but I have been to busy to try it out to see how much
of a difference it makes yet. I was experimenting with the 10 inch wire and
made so much CS I can take the next few weeks off and do other things.
I purchased my 12 ga. 99.99% wire from CCSILVER.COM, I do not know if they deal
with really small orders but they took mine. I ordered 25 feet of 14ga. and 6
feet of 12ga, price is right also.  Look them up..

Mike Leavitt

"G. Boucher" wrote:

> Hi Ron:
>
> Thank you for your reply.
>
> I believe that we are all learning and if we do not
> ask questions, I presume that it would take a long
> time to learn.
>
> Yes I know a little bit about current. I was not aware
> of what you were using as Silver ( size, etc) You may
> have mentionned it, but if you did I missed it.
> I am using Silver wire #14, approx 4 inches long
> with 3 1/4 inches in water. And this is what I get
> approx. 120 to 150 microamps at the start with
> distilled water. If I heat the water, I double this
> amount at the start.
>
> The same applies with the distance of electrodes.
> It will change the current slightly. But according
> to feedback on this list the best distance is between
> 2 1/4 to 2 1/2 inches.
>
> The current never went up to 6MA yet on the few
> batches that I have produced so far. The maximum was approx.
> 4MA at the end of the batch (2 1/2 hrs) with the small
> size wire that I am using.
>
> Ron, if you are using, larger than # 14 wire, I would
> appreciate to know where you obtain it. Pls send
> the reply to my private e-mail if you can. Thanks again.
>
> Gaston
> ============================================
> ----- Message d'origine -----
> De : Ron Hackley <[email protected]>
> À : <[email protected]>
> Envoyé : 2 avril, 2000 20:31
> Objet : Re: CS>Making CS
>
> > Hi Gaston & List...
> >
> > I'm sure not the one to be getting advise from, but I'm glad to share my
> > experiences and thoughts on CS. The following pertains to Gaston's
> > posting that's below.
> >
> > 1. I don't use a starter other than a few ounces of my previous batch,
> > and I sometimes forget that. For several years prior to joining this
> > list I was adding a drop or two of very dilute sea salt solution as some
> > web pages have suggested. In about twenty minutes I had a somewhat gray
> > solution. We drank it and it seemed to work (no colds etc.) and we
> > didn't turn gray. It seemed to work as well (or better?) on cuts and
> > scratches as the clearer solution. However, the arguments on the list
> > convinced me to switch over to the slower method, particularly for
> > silver taken internally.
> >
> > 2. and 3. I don't have CS test instruments YET beyond an ammeter/VOM so
> > I don't know what PPM or uS it is yet. Will post when I know. CS gets
> > used up pretty fast here so it doesn't sit around long, but I haven't
> > noticed any plating out in the bottles I use.
> >
> > Concerning current flow differences and recommendations; that probably
> > has something to do with the surface area of the electrodes. I use a
> > silver round which has a lot more surface area than a silver wire, hence
> > more current doesn't necessarily translate into a higher current density
> > at any specific point on the anode. I just started a batch of CS and the
> > starting current using the round was about 1.1ma. Then I unplugged the
> > round and plugged in the 3" long #14 silver wire I used to use and the
> > current dropped to 120uA.
> >
> > There seem to be many ways to make good (and bad) CS. I think if one can
> > make ANY CS they have an important tool, and then we can work to refine
> > and make it better. I don't think anyone should hold off making CS
> > because they are afraid they won't make it right or something. (I know
> > this doesn't apply to you Gaston, but once I start commenting it's
> > sometimes hard to stop:).
> >
> > Ron
> >
> >
> > "G. Boucher" wrote:
> > >
> > > Hi Ron
> > >
> > > Good to hear from you on CS.
> > >
> > > I am new to the CS and I would like to know from your experience:
> > >
> > > 1.- Do you use any starter to produce your cs other than
> > >      a mixture from the previous batch ?
> > >
> > > 2.- Do you know the strength of your CS in either PPM or microSiemens ?
> > >
> > > 3.- Do you notice a decrease in PPM or Microsiemens 24 hours
> > >      after production ?
> > >
> > > I normally read 0.15 MA with distilled water at the start and heated
> > > I read around 0.25 to 0.35 MA.
> > >
> > > It is interesting to hear that you see T. E. at around 6 MA. Many
> > > CS producers recommend to use a limiting current of 0.8MA
> > > to produce cs. Does that mean that T. E. is not present with that
> > > kind of low current ?
> > >
> > > >From what I read, apprarently, low current is better to produce
> > > small particles. It seems to take longer to prduce CS with a low
> > > current and this is probably why we do get yellow CS.
> > >
> > > <snip>
> > >
> >
> >
> > --
> > The silver-list is a moderated forum for discussion of colloidal silver.
> >
> > To join or quit silver-list or silver-digest send an e-mail message to:
> > [email protected]  -or-  [email protected]
> > with the word subscribe or unsubscribe in the SUBJECT line.
> >
> > To post, address your message to: [email protected]
> > Silver-list archive: http://escribe.com/health/thesilverlist/index.html
> > List maintainer: Mike Devour <[email protected]>
> >