Methinks not to worry.
There's a few ways to make CS right and many many ways to do it wrong.
You'd be TRYing to do it wrong and will have a hard time failing.
The main thing about using high voltage here is to achieve a high current
over a certain distance in water.
You have 240 volts available? Run it through a big ole rectifer to get
full or half wave DC with a circuit breaker to prevent fires, [use a
breaker a little less than what the rectifier is rated at] toss a couple of
silver bars into a vat of water..step back and throw the switch.
If the wires heat up, use bigger ones. [or smaller electrodes]
When the breaker kicks you out, look at what happened. It'll be bad. Bad
enough? No? Use a bigger rectifier, wires and breaker.
You oughta be able to make a real mess.
Be careful. Stand back.
Ode
At 04:29 AM 11/19/2003 +0530, you wrote:
>Ode,
>Thanks for this information, which seems to be another good methodology.
>We're now working up a real list of methodologies. The creation of
>silver sludge, using very high voltage, etc., would seem to be
>promising. Off hand what would you imagine the setup would cost? I
>hear '20,000 volts,' and imagine some very beefy, expensive devices.
>And when the electrodes disintegrate do they do so uniformly? I'm also
>imagining there would be some big chunks of metalic silver that would
>have to go back for melting and reworking.
>Thanks,
>Reid
>
>Ode said:
>The way I see it is that the effects of silver on microbes depends on
>'available' surface area.
> In a liquid, that surface area can be huge depending on the size of the
>
>particles.
> In a solid, it will be limited by the exposure possible at a given
>porosity...that is, the size of the pore in the filter will determine
>the
>maximum exposure of silver to the water going through it by the surface
>area presented by the pore.
> The best you can do is to make very small pores entirely coated with
>silver.
> The silver that's not on the pore surface will do nothing at all.
> If it's possible to make tiny, close packed but still seperate beads of
>
>silver on the pore surface, THAT may increase surface area exposure over
>a
>solid sheet.
>
> So, "possibly", saturating the filter with oxide particles small enough
>to
>get into the pores and burning off the oxygen in the oxide during
>fireing
>will make those micro beads that stay stuck to the clay surface.
> If you're using sawdust to determine the size of the pore in the clay,
>perhaps soaking the sawdust with silver oxide sludge will do it. [Or
>specifically sized...by screening?... charcoal chunks?]
>
> It's not hard to make CS sludge. [Lots of voltage and current and
>enough
>time to disintigrate the electrode..done wrong the right way, mere
>minutes.
> Guessing 20,000 volts at a few amps?]
> If voltage and current is high enough, the sludge will actually
>emulsify.
>It will be deep brown turning to quite black.
> { I discovered the best way to not make good CS first off...slight fire
>
>hazard there too.}
>
> Patterson [forget the first name...James?] patented micro beads and
>made
>millions when it became apparent that they had unique delivery
>properties
>for many cosmetics and drugs depending on what the bead coating was.
> Many products you buy today have that feature.
> Patterson is the guy who now is playing with a cold fusion process that
>
>uses micro beads. [Microscopic round particles coated with another
>material...palladium?]
>
> This will be too high tech to do in the field, but it seems like
>spraying
>very fine clay dust [or silica to make glass beads?] into a vaccuum
>along
>with a silver plasma will result in such a bead which then could be
>pressure packed or sintered together to form a pourous shape.
>
> I've seen various filters [especially fuel filters] made by packing
>small
>round metallic shapes together..perhaps bonded by heating them to the
>point
>of stickyness [like spot welding] or perhaps simply by applying large
>amounts of pressure in a mold. The size of the bead and extent of the
>packing effect determines the porosity.
>
>Ode
>
>
>
>--
>The silver-list is a moderated forum for discussion of colloidal silver.
>
>Instructions for unsubscribing may be found at: http://silverlist.org
>
>To post, address your message to: [email protected]
>
>Silver-list archive: http://escribe.com/health/thesilverlist/index.html
>
>List maintainer: Mike Devour <[email protected]>
>
>