The tarnish was on the silver rods and ran down the jar near where the rods
ended. When I moved the rods it came off of them. I did strain the batch and it
was a film of black dots on the bottom of the filter. The CS came out a soft
yellowy clear color.
----- Original Message -----
From: Ode Coyote
To: silver-list@eskimo.com
Sent: Monday, May 09, 2005 3:38 AM
Subject: Re: CS>
Black tarnish where?
Ode
At 07:07 AM 5/7/2005 -0700, you wrote:
>>>>
this is a brand new machine. and My first batch. Does anyone know about the
black tarnish?
I did clean the jar with dish soap but I really rinsed in well. I flushed
it because I was concerned about using soap. could this be a factor?
----- Original Message -----
From: <mailto:odecoy...@alltel.net>Ode Coyote
To: <mailto:silver-list@eskimo.com>silver-list@eskimo.com
Sent: Saturday, May 07, 2005 2:59 AM
Subject: Re: CS>
Heavy deposits on the electrodes can defeat conductivity sensing auto off
circuits by semi-insulating the electrodes. At some point, they just get
heavier and heavier and make a mess.
Don't worry about light. If you haven't used salt or baking soda, you can
run a generator in direct sun and store CS on a sunny windowsill.
Silver in 'only' distilled water is not photo-reactive.
If you find that it is, there was something else in the water.
Ode
At 05:16 PM 5/6/2005 -0700, you wrote:
>>>>
Thanks it's been 26 hours and the light is still on. Should I through
it out? I just took a peak and the silver rods are tarnished with black (like
silver tarnish) and when I shook them it feel of and was making it's way to the
bottom. Also there are two tarnish lines run down the jar. From the bottom of
the rod to the bottom.
any thoughts, please
worried cook
----- Original Message -----
From: <mailto:ke...@shaw.ca>kent
To: <mailto:silver-list@eskimo.com>silver-list@eskimo.com
Sent: Friday, May 06, 2005 3:42 PM
Subject: **SPAM: RE: CS>first batch
I have a colloid master as well. My usual setting is 6 to 6.5. The
PPM tester is anywhere between 14 to 20. Which I understand correctly from the
list is doubled to come up with the correct the PPM. It should be
clear/slightly yellow at the end of the brewing cycle. It can take a bit of
time. I do not let mine sit for 36 hours before I use it. I also do not filter
it. Not sure if this causes any problems but I haven't turned gray yet
Kent
-----Original Message-----
From: SCD Traveler [mailto:s...@cox.net]
Sent: Friday, May 06, 2005 7:23 AM
To: silver-list@eskimo.com
Subject: CS>first batch
Well I started my first batch yesterday at 4 PM. It's now 7 AM and
it's not done. I have a colloid master and when I did the test for water purity
it was just fine (Arrowhead distilled) So I'm not sure what to do now. I'm
concerned. I did want a higher PPM so it's set on 6. I'm concerned about the
keep in the dark thing." Why would that make a difference. Can I lift the box
and look at it or would that ruin the batch and what about taking the box off
to remove the silver and let set for 36 hours. It's seems more difficult that I
thought it would be because of the darkness thing. I seen a post here about
fuzz does' that stop the process and what about lifting the box to see if I
have fuzz.
thanks for any input
worried cook
No virus found in this incoming message.
Checked by AVG Anti-Virus.
Version: 7.0.308 / Virus Database: 266.11.5 - Release Date: 5/4/2005
<<<<
----------
No virus found in this outgoing message.
Checked by AVG Anti-Virus.
Version: 7.0.308 / Virus Database: 266.11.5 - Release Date: 5/4/2005
No virus found in this incoming message.
Checked by AVG Anti-Virus.
Version: 7.0.308 / Virus Database: 266.11.6 - Release Date: 5/6/2005
<<<<
------------------------------------------------------------------------------
No virus found in this outgoing message.
Checked by AVG Anti-Virus.
Version: 7.0.308 / Virus Database: 266.11.7 - Release Date: 5/9/2005
