Re: [smartBridges] Slow down problems

[Blazen Wireless]

Different SSID no roaming Derek trust me I have tried EVERY option that you and SB has given me there is nothing that I have not tried.. It progressively gets worse as I add more clients.   1. I change the ssid on the APS to something different and change like 10 or less customers CPE to match and the problem GOES AWAY!!!!!!!   Tell me that is not an issue with how much capacity the APPO can handle? I mean it sounds as though you all want to lay claim just like SB that GEE it cant be their equipment? Have we not all learned from the past that it has most the time been a issue with the equipment Just think this stuff is junk when it comes to handling lots of clients in an area thats congested with other 802.11 traffic and it just plain and simple cant handle it. I am sure if SB would have taken our suggestions almost 5 months ago so send someone out to investigate they would learn a allot of how and what affects their products!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!         ----- Original Message ----- From: Derek Breiland To: [EMAIL PROTECTED] Sent: Tuesday, October 28, 2003 10:02 PM Subject: Re: [smartBridges] Slow down problems So, you are using different SSID's?  Are you set for roaming on the clients? ----- Original Message ----- From: Blazen Wireless To: [EMAIL PROTECTED] Sent: Tuesday, October 28, 2003 11:35 PM Subject: Re: [smartBridges] Slow down problems No different SSIDS and different channels ones is on 4 one was on 7 and they have been working fine. They were even working fine both on chan 3 so channel is NOT the issue. Everyone is trying to read more into this then what I believe to be the problem LESS users system is great MORE users system is crap   ----- Original Message ----- From: Derek Breiland To: [EMAIL PROTECTED] Sent: Tuesday, October 28, 2003 9:24 PM Subject: Re: [smartBridges] Slow down problems What antennas and channels are you using?  Same SSID's on both AP's? ----- Original Message ----- From: Blazen Wireless To: [EMAIL PROTECTED] Sent: Tuesday, October 28, 2003 11:22 PM Subject: Re: [smartBridges] Slow down problems Power is not an issue how can power be an issue when the power strip is 2 inches away from the radio. The radios has LMR 400 jumper going to a amp power supply then 50ft of LMR 400 going to the amp at the ant then from the amp to the ant..   And YES I have tried the system without any amps and basically I get 1 5 users associated.   ----- Original Message ----- From: Derek Breiland To: [EMAIL PROTECTED] Sent: Tuesday, October 28, 2003 8:17 PM Subject: Re: [smartBridges] Slow down problems The toehr thing, as it was mentioned in a differnet reply earlier, are you using 18VDC power supplies?  Are the AP's lacking the power they need? ----- Original Message ----- From: Blazen Wireless To: [EMAIL PROTECTED] Sent: Tuesday, October 28, 2003 5:17 PM Subject: [smartBridges] Slow down problems We give up! We cant add any more users to our system total of 60 split between 2 APPO's 30 each at max. We added 2 more today and now we have hardly any users downloading and best we can do is about 300KBPS down... This SUCKS! is it possibly due to all the smoke in the air which I would find hard to believe BUT you never know.   What's the deal with the XO stuff is it done it sure could be nice to have one to test and see if it is worth $900.. I am very frustrated at not being able to figure this out. It all points back to the radios (APPO's) not being able to process all the associated radios to it? I change the SSID so only a few people 10-12 can associate to the APPO and there is NO pro problems. I allow all the users to associate to the APPO and WHAM crap city throughput goes to hell pings skyrocket just with one user surfing on and off.. how can this NOT point to the radios inability to keep up? Why would just idle radios associated to the APPO have such a bad effect on the APPO?   I have 6 users ready to cancel due to the crappy service I am getting from these radios I don't understand how someone else claims 60 plus users on ONE APPO and they are fine? what speeds are you offering what are your settings on the APPO and the clients associated to it. What ant are you using? any amps etc etc..         Martin & Steve Blazen Wireless www.blazenwireless.com