Hey wait... what type of CPE? Anything based on Orinoco? Their OSU management stuff would probably cause that difference.
Scott -----Original Message----- From: "Colin Watson" <[EMAIL PROTECTED]> To: <[EMAIL PROTECTED]> Date: Fri, 31 Oct 2003 18:01:34 -0000 Subject: Re: [smartBridges] Throughput errors on Airpoint Pro Outdoor > Plug a laptop into the switch that collates your four APPO's and run > ethereal (http://www.ethereal.com - it's free) and set it to capture > packets > on the laptop. This will show you whats traversing the network. If > broadcast > storms are occuring, you will see large numbers of packets appearing, > and > when you finally view the contents - you will be able to determine the > offender. Ideally you want to ensure you either have a router at the > tower > (to prevent broadcasts from propogating), and ensure your customers > have > their CPE connected to a router, and not a hub or a switch (as I have > seen > done). Hubs are especially dangerous, as they forward all traffic out > of > every port, and as SmartBridge CPE can mask 64? MAC addresses in it's > own, > if a customer is copying to a local machine on their network you will > receive their broadcasts. Consider that if they are running on a > 100Mbit > network, your smartbridge will be hogging all the AP's attention as it > forwards the maximum amount (of pointless crap) it can to your tower. > Still, > an ethereal dump of traffic will show you if this is occuring and who's > responsible. > > ----- Original Message ----- > From: "shoffman" <[EMAIL PROTECTED]> > To: <[EMAIL PROTECTED]> > Sent: Friday, October 31, 2003 4:49 PM > Subject: Re: [smartBridges] Throughput errors on Airpoint Pro Outdoor > > > > Realize that the Smartbridge stuff is pretty sensative so you may be > > seeing more of a cross talk effect then your previous gear. You > should > > see if "tuning down" the clients helps your situation. > > > > You should be able to see if your storm theory is correct with the > > Ethernet statistics on the AP's. > > > > > > Scott > > > > > > -----Original Message----- > > From: "Shane Mitchell" <[EMAIL PROTECTED]> > > To: <[EMAIL PROTECTED]> > > Date: Fri, 31 Oct 2003 10:06:42 -0600 > > Subject: [smartBridges] Throughput errors on Airpoint Pro Outdoor > > > > > I am a new user of these items with 4 of them on a water tower. > Each > > > AP > > > has approximately 25 clients presently. The old AP's I was using > were > > > providing about 2.5 mbps at peak, however, we are only getting > about > > > 1.8mbps at peak now. Also, clients are reporting traffic being > > > "Jerky", > > > with bursts of speed, followed by lags. I have tinkered with > RTS/CTS, > > > but it has not improved it, so I have disabled it again. > > > > > > I am beginning to suspect broadcast storm traffic from each AP to > the > > > switch and back out to the other AP's, but I'm not sure this is > > > correct. > > > Any suggestions? > > > > > > Shane Mitchell > > > > > > > The PART-15.ORG smartBridges Discussion List > > To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe > smartBridges <yournickname> > > To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe > smartBridges) > > Archives: http://archives.part-15.org > > > > > > > > The PART-15.ORG smartBridges Discussion List > To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe > smartBridges <yournickname> > To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe > smartBridges) > Archives: http://archives.part-15.org The PART-15.ORG smartBridges Discussion List To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges <yournickname> To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) Archives: http://archives.part-15.org
