Downgraded the bios to 1.32d on this particular 5501 and the problems still occur:
#1 - "MII without any phy!" in all vr interfaces; same CF (SiliconDrive CF SSD-C01G-3550) on other 5501's (1.32d) will work fine; I can't say if the problem occurred before the upgrade to 1.32h since this 5501 wasn't in use. #2 - the box won't boot off a SanDisk 512Mb; it takes a few seconds to probe and then it won't boot off of it (sequence is 80 81 F0 FF); this same SanDisk 512 will boot other 5501's (only tried with 1.32d); this box will boot off the above mentioned SiliconDrive CF. Both CFs have same OS image (day-old FBSD6.2-STABLE) #3 - somebody had mentioned some CFs showing up as ad0 and ad1; The other 5501 where these flashes boot, will show the SanDisk as ad0, whereas when booted off the SiliconDrive CF, ad1. Not sure if some/all pertains to your BIOS update but I would welcome your input about these issues. Thanks. ervin wrote: > I don't think so ... I'm running 6.2 as well and no issues after the upgrade > :-) > > On 04/10/2007, Joao Pedras <[EMAIL PROTECTED]> wrote: >> Joao Pedras wrote: >>> Mike Tancsa wrote: >>>> At 07:51 PM 10/3/2007, Soren Kristensen wrote: >>>>> Hi Everybody, >>>>> >>>>> I just posted a net5501 BIOS update with: >>>>> comBIOS vers 1.32h >>>>> >>>>> * fixed IDE DMA enable issue on net5501 >>>>> * fixed soft reboot issue on net5501 >>>> Hi, >>>> Unfortunately, I still see the soft reboot issue on FreeBSD. >>>> e.g. from the bootloader prompt, if I try to reboot, the box will >>>> hang and never reboot >>>> >>>> Nothing fancy about my bios settings, other than the speed is set to 9600 >>>> >>>> >>>> >>>> POST: 012345689bcefghips1234ajklnopqr,,,tvwxy >>>> >>>> >>>> >>>> >>>> >>>> >>>> >>>> >>>> comBIOS ver. 1.32h 20071004 Copyright (C) 2000-2007 Soekris Engineering. >>>> >>>> net5501 >>>> >>>> 0512 Mbyte Memory CPU Geode LX 500 Mhz >>>> >>>> Pri Sla LEXAR ATA FLASH LBA 994-16-63 501 Mbyte >>>> >>>> Slot Vend Dev ClassRev Cmd Stat CL LT HT Base1 Base2 Int >>>> ------------------------------------------------------------------- >>>> 0:01:2 1022 2082 10100000 0006 0220 08 00 00 A0000000 00000000 10 >>>> 0:06:0 1106 3053 02000096 0117 0210 08 40 00 0000E101 A0004000 11 >>>> 0:07:0 1106 3053 02000096 0117 0210 08 40 00 0000E201 A0004100 05 >>>> 0:08:0 1106 3053 02000096 0117 0210 08 40 00 0000E301 A0004200 09 >>>> 0:09:0 1106 3053 02000096 0117 0210 08 40 00 0000E401 A0004300 12 >>>> 0:20:0 1022 2090 06010003 0009 02A0 08 40 80 00006001 00006101 >>>> 0:20:2 1022 209A 01018001 0005 02A0 08 00 00 00000000 00000000 >>>> 0:21:0 1022 2094 0C031002 0006 0230 08 00 80 A0005000 00000000 15 >>>> 0:21:1 1022 2095 0C032002 0006 0230 08 00 00 A0006000 00000000 15 >>>> >>>> 1 Seconds to automatic boot. Press Ctrl-P for entering Monitor. >>>> >>>> 1 FreeBSD >>>> 2 FreeBSD >>>> >>>> Default: 1 >>>> >>>> /boot.config: -hConsoles: serial port >>>> BIOS drive C: is disk0 >>>> BIOS 639kB/523264kB available memory >>>> >>>> FreeBSD/i386 bootstrap loader, Revision 1.1 >>>> ([EMAIL PROTECTED], Sat Sep 15 01:52:01 EDT 2007) >>>> Loading /boot/defaults/loader.conf >>>> /boot/kernel/kernel text=0x258e14 data=0x2bed4+0x16018 >>>> syms=[0x4+0x359d0+0x4+0x45239] >>>> - >>>> Hit [Enter] to boot immediately, or any other key for command prompt. >>>> >>>> >>>> Type '?' for a list of commands, 'help' for more detailed help. >>>> OK reboot >>>> Rebooting... >>>> >>>> at this point its totally hung and needs a power cycle >>>> >>>> >>>> >>>> >>>> dmesg looks like the following >>>> >>>> >>>> Copyright (c) 1992-2007 The FreeBSD Project. >>>> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 >>>> The Regents of the University of California. All rights reserved. >>>> FreeBSD is a registered trademark of The FreeBSD Foundation. >>>> FreeBSD 6.2-STABLE #1: Tue Sep 18 11:35:06 EDT 2007 >>>> [EMAIL PROTECTED]:/usr/obj/nanobsd-soekris5501/usr/src/sys/nano5501 >>>> Timecounter "i8254" frequency 1193182 Hz quality 0 >>>> CPU: Geode(TM) Integrated Processor by AMD PCS (499.90-MHz 586-class CPU) >>>> Origin = "AuthenticAMD" Id = 0x5a2 Stepping = 2 >>>> Features=0x88a93d<FPU,DE,PSE,TSC,MSR,CX8,SEP,PGE,CMOV,CLFLUSH,MMX> >>>> AMD Features=0xc0400000<MMX+,3DNow+,3DNow> >>>> real memory = 536870912 (512 MB) >>>> avail memory = 520265728 (496 MB) >>>> K6-family MTRR support enabled (2 registers) >>>> cpu0 on motherboard >>>> pcib0: <Host to PCI bridge> pcibus 0 on motherboard >>>> pci0: <PCI bus> on pcib0 >>>> Geode LX: Soekris net5501 comBIOS ver. 1.32h 20071004 Copyright (C) >>>> 2000-2007 >>>> MFGPT bar: f00100006200 >>>> pci0: <encrypt/decrypt, entertainment crypto> at device 1.2 (no >>>> driver attached) >>>> vr0: <VIA VT6105M Rhine III 10/100BaseTX> port 0xe100-0xe1ff mem >>>> 0xa0004000-0xa00040ff irq 11 at device 6.0 on pci0 >>>> miibus0: <MII bus> on vr0 >>>> ukphy0: <Generic IEEE 802.3u media interface> on miibus0 >>>> ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto >>>> vr0: Ethernet address: 00:00:24:c8:e2:24 >>>> vr1: <VIA VT6105M Rhine III 10/100BaseTX> port 0xe200-0xe2ff mem >>>> 0xa0004100-0xa00041ff irq 5 at device 7.0 on pci0 >>>> miibus1: <MII bus> on vr1 >>>> ukphy1: <Generic IEEE 802.3u media interface> on miibus1 >>>> ukphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto >>>> vr1: Ethernet address: 00:00:24:c8:e2:25 >>>> vr2: <VIA VT6105M Rhine III 10/100BaseTX> port 0xe300-0xe3ff mem >>>> 0xa0004200-0xa00042ff irq 9 at device 8.0 on pci0 >>>> miibus2: <MII bus> on vr2 >>>> ukphy2: <Generic IEEE 802.3u media interface> on miibus2 >>>> ukphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto >>>> vr2: Ethernet address: 00:00:24:c8:e2:26 >>>> vr3: <VIA VT6105M Rhine III 10/100BaseTX> port 0xe400-0xe4ff mem >>>> 0xa0004300-0xa00043ff irq 12 at device 9.0 on pci0 >>>> miibus3: <MII bus> on vr3 >>>> ukphy3: <Generic IEEE 802.3u media interface> on miibus3 >>>> ukphy3: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto >>>> vr3: Ethernet address: 00:00:24:c8:e2:27 >>>> isab0: <PCI-ISA bridge> at device 20.0 on pci0 >>>> isa0: <ISA bus> on isab0 >>>> atapci0: <GENERIC ATA controller> port >>>> 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xe000-0xe00f at device 20.2 on pci0 >>>> ata0: <ATA channel 0> on atapci0 >>>> ata1: <ATA channel 1> on atapci0 >>>> ohci0: <OHCI (generic) USB controller> mem 0xa0005000-0xa0005fff irq >>>> 15 at device 21.0 on pci0 >>>> ohci0: [GIANT-LOCKED] >>>> usb0: OHCI version 1.0, legacy support >>>> usb0: <OHCI (generic) USB controller> on ohci0 >>>> usb0: USB revision 1.0 >>>> uhub0: AMD OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 >>>> uhub0: 4 ports with 4 removable, self powered >>>> pci0: <serial bus, USB> at device 21.1 (no driver attached) >>>> orm0: <ISA Option ROM> at iomem 0xc8000-0xd27ff on isa0 >>>> sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 >>>> sio0: type 16550A, console >>>> sio1 at port 0x2f8-0x2ff irq 3 on isa0 >>>> sio1: type 16550A >>>> Timecounter "TSC" frequency 499904611 Hz quality 800 >>>> Timecounters tick every 1.000 msec >>>> ad1: 489MB <LEXAR ATA FLASH V1.02> at ata0-slave PIO4 >>>> Trying to mount root from ufs:/dev/ad1s1a >>>> >>>> >>>> ---Mike >>>> >>>> >>>>> * change initial clear screen to scroll lines >>>>> >>>>> There might still be issues with Ultra-DMA detect/setting, I would be >>>>> happy to get a few success/failure reports, just email me directly. >>>>> >>>>> Also, I'm still investigating how 40/80 wire cable reporting should be >>>>> done.... >>>>> >>>>> >>>>> Best Regards, >>>>> >>>>> >>>>> Soren Kristensen >>>>> >>>>> CEO & Chief Engineer >>>>> Soekris Engineering, Inc. >>>>> >>>>> _______________________________________________ >>>>> Soekris-tech mailing list >>>>> Soekris-tech@lists.soekris.com >>>>> http://lists.soekris.com/mailman/listinfo/soekris-tech >>>> _______________________________________________ >>>> Soekris-tech mailing list >>>> Soekris-tech@lists.soekris.com >>>> http://lists.soekris.com/mailman/listinfo/soekris-tech >>> Same problem here, with the soft boot. >>> >>> Additionaly, when inserting a SANDISK 512Mb, it doesn't boot. I am not >>> sure if this is related with your recent issues since this was the first >>> time I tried this particular flash on the 5501. It was working well on a >>> 4801 and it has always been used read-only. >>> >>> It locks up/stops right before this part shows up (ie. this never showsup): >>> >>> Slot Vend Dev ClassRev Cmd Stat CL LT HT Base1 Base2 Int >>> ------------------------------------------------------------------- >>> 0:01:2 1022 2082 10100000 0006 0220 08 00 00 A0000000 00000000 10 >>> 0:06:0 1106 3053 02000096 0117 0210 08 40 00 0000E101 A0004000 11 >>> 0:07:0 1106 3053 02000096 0117 0210 08 40 00 0000E201 A0004100 05 >>> 0:08:0 1106 3053 02000096 0117 0210 08 40 00 0000E301 A0004200 09 >>> 0:09:0 1106 3053 02000096 0117 0210 08 40 00 0000E401 A0004300 12 >>> >>> >>> Thanks. >>> _______________________________________________ >>> Soekris-tech mailing list >>> Soekris-tech@lists.soekris.com >>> http://lists.soekris.com/mailman/listinfo/soekris-tech >> I am not sure if this is related as well. >> >> The only box I have with the new bios, booting FreeBSD 6.2-STABLE from >> yesterday, is not able to bring the vr interfaces up. During kernel >> probing the message "MII without any phy!" shows up with all of them. >> >> First I thought I had messed up my kernel config but I really didn't >> changed anything. >> >> I just had the chance to boot the *exact* same flash on a 5501 with the >> previous BIOS version and the problem does not occur. >> >> Again, not sure if this is related with your new BIOS version. >> >> Thanks! >> _______________________________________________ >> Soekris-tech mailing list >> Soekris-tech@lists.soekris.com >> http://lists.soekris.com/mailman/listinfo/soekris-tech >> > > _______________________________________________ Soekris-tech mailing list Soekris-tech@lists.soekris.com http://lists.soekris.com/mailman/listinfo/soekris-tech