Good idea Bill. Is this because there is data on fuel loads, burning rates, etc?, so from there, one could find a range for the less definite loads and configurations?
-----Original Message----- From: Bill Brooks [mailto:[email protected]] Sent: Monday, February 28, 2011 4:24 PM To: [email protected] Subject: RE: re- 'seeing' heat release rate Perhaps you could start by defining the differences among Group A, B, and C plastics, along with what configurations of each dictate the current NFPA 13 protection methods. Bill Brooks William N. Brooks, P.E. Brooks Fire Protection Engineering Inc. 372 Wilett Drive Severna Park, MD 21146-1904 410-544-3620 410-544-3032 FAX 412-400-6528 Cell -----Original Message----- From: [email protected] [mailto:[email protected]] On Behalf Of Brad Casterline Sent: Monday, February 28, 2011 4:46 PM To: [email protected] Subject: RE: re- 'seeing' heat release rate Steve, ya, I need to let this go (Forum-wise at least), since 13 says Installation..., not Theory and Installation :). I need to find an SFPE handbook and spend years trying to figure out what 2+3 is. Still, it would be nice for something as basic to all of 13 as Heat Release Rate, Quantity, and Combustibility to have at least a range of numbers attached to the words, in the annex anyway. Thanks, Brad -----Original Message----- From: Steve Leyton [mailto:[email protected]] Sent: Monday, February 28, 2011 2:56 PM To: [email protected] Subject: RE: re- 'seeing' heat release rate Brad: I don't want to open a bucket of worms discussion-wise, but obviously, what's burning in a "typical" light or ordinary hazard compartment could be very different within a "uniform" hazard group occupancy. If my desk and the mountain of papers scattered across it were to be involved in a fire, the overall release would be WAY lower than if the sofa in our lobby was involved. All light hazard, but our lobby is a much higher potential energy load. SL ________________________________ From: [email protected] on behalf of Brad Casterline Sent: Sun 2/27/2011 10:22 AM To: [email protected] Subject: re- 'seeing' heat release rate Experimenters have shown that the Heat of Combustion for a wide range of combustibles is directly proportional to the amount of O2 consumed= 13,100 Kj/Kg (12,428 BTU/lb). If so, 1 gallon of water per square foot will handle 7 pounds of fuel per square foot. A Christmas tree lot would only be LH if business had been good and this was Christmas Eve. Now the Burning Unit is a box weighing 19 pounds~ a 'case'*~~ playing like beer is an average combustible. A study of 3 hospitals in 1942 came up with an average fuel load of ~6 pounds per square foot- (an 8-pack). How hot is a Light Hazard Fire? I have no idea. *When I dropped out of college a 'case' was 24 beers. According to the fraternity I TAPPA KEG, a 'case' is now 30 beers. I still use 24. Ps- At the risk of spinning this until ridiculously twisted, how satisfying would it be to look for Max Deflector Distance and find- For Unobstructed Construction= Not TOO far down. For Obstructed Construction= 1.83 times Unobstructed. ? _______________________________________________ Sprinklerforum mailing list [email protected] http://fireball.firesprinkler.org/mailman/listinfo/sprinklerforum For Technical Assistance, send an email to: [email protected] To Unsubscribe, send an email to:[email protected] (Put the word unsubscribe in the subject field) _______________________________________________ Sprinklerforum mailing list [email protected] http://fireball.firesprinkler.org/mailman/listinfo/sprinklerforum For Technical Assistance, send an email to: [email protected] To Unsubscribe, send an email to:[email protected] (Put the word unsubscribe in the subject field) _______________________________________________ Sprinklerforum mailing list [email protected] http://fireball.firesprinkler.org/mailman/listinfo/sprinklerforum For Technical Assistance, send an email to: [email protected] To Unsubscribe, send an email to:[email protected] (Put the word unsubscribe in the subject field) _______________________________________________ Sprinklerforum mailing list [email protected] http://fireball.firesprinkler.org/mailman/listinfo/sprinklerforum For Technical Assistance, send an email to: [email protected] To Unsubscribe, send an email to:[email protected] (Put the word unsubscribe in the subject field) _______________________________________________ Sprinklerforum mailing list [email protected] http://fireball.firesprinkler.org/mailman/listinfo/sprinklerforum For Technical Assistance, send an email to: [email protected] To Unsubscribe, send an email to:[email protected] (Put the word unsubscribe in the subject field)
