I only had to hand calc grids for my NICET test of course with velocity pressures... Never again!
Sent from my iPhone Aaron M. Peck, SET Fire Protection Skype +1(202)407-9079 Cambodia +855(0)78700407 > On Mar 14, 2014, at 12:30 AM, Sharon Alves <[email protected]> wrote: > > I hate to admit it, but I calculated grids by hand. > > Thank you, > > Sharon Alves > Senior Fire Sprinkler Specialist, Project Manager, SET > > > > LP Consulting Engineers, Inc. > MEP/FS . Sustainability . CxA > 1663 Eureka Rd - Roseville, CA 95661 > (916) 771-0778 x114 > [email protected] > www.lpengineers.com > > > This email and its attachments are the sole property of LP Consulting > Engineers, Inc. and Copyrighted by LP Consulting Engineers, Inc. 2013. This > communication with its contents may contain confidential and/or legally > privileged information. It is solely for the use of the intended > recipient(s). Unauthorized interception, review, use or disclosure is > prohibited and may violate applicable laws including the Electronic > Communications Privacy Act. If you are not the intended recipient, please > contact the sender and destroy all copies of the communication. The sender > and its company do not guarantee that this email or its attachments is free > of viruses nor does it accept any liability for same. > > -----Original Message----- > From: [email protected] > [mailto:[email protected]] On Behalf Of Aaron > Peck > Sent: Thursday, March 13, 2014 9:58 AM > To: [email protected] > Subject: Re: Pre-fabbed Hangers and Drops > > Was that along with punchcard hydraulics? Lol > > I wish I had been better but I had my moments of very nice fit jobs. > Coordinating around huge duct work. The foreman called me out to find out > what I was on during this design. I just said wait and see. He was amazed > when the duct came in and it worked perfectly. > > More proper coordination instead of prefab. > > Sent from my iPhone > Aaron M. Peck, SET Fire Protection > Skype +1(202)407-9079 > Cambodia +855(0)78700407 > >> On Mar 13, 2014, at 11:47 PM, Sharon Alves <[email protected]> wrote: >> >> Back in the day (when the earth was new) we would cut everything to fit. >> That was our job as designers. >> >> Thank you, >> >> Sharon Alves >> Senior Fire Sprinkler Specialist, Project Manager, SET >> >> >> >> LP Consulting Engineers, Inc. >> MEP/FS . Sustainability . CxA >> 1663 Eureka Rd - Roseville, CA 95661 >> (916) 771-0778 x114 >> [email protected] >> www.lpengineers.com >> >> >> This email and its attachments are the sole property of LP Consulting >> Engineers, Inc. and Copyrighted by LP Consulting Engineers, Inc. 2013. This >> communication with its contents may contain confidential and/or legally >> privileged information. It is solely for the use of the intended >> recipient(s). Unauthorized interception, review, use or disclosure is >> prohibited and may violate applicable laws including the Electronic >> Communications Privacy Act. If you are not the intended recipient, please >> contact the sender and destroy all copies of the communication. The sender >> and its company do not guarantee that this email or its attachments is free >> of viruses nor does it accept any liability for same. >> >> -----Original Message----- >> From: [email protected] >> [mailto:[email protected]] On Behalf Of >> Aaron Peck >> Sent: Thursday, March 13, 2014 9:35 AM >> To: [email protected] >> Cc: [email protected] >> Subject: Re: Pre-fabbed Hangers and Drops >> >> Better men then me can do it. I was hit or miss. More miss than hit. I would >> even run it by the field super to make sure I was figuring it right. >> >> Usually took me actually doing a small mock up in the shop to be 100% sure. >> >> There was a guy in my office when I started. He could have the whole job >> pre-fabbed and he usually had a 97% fit rate. >> >> God speed! >> >> Sent from my iPhone >> Aaron M. Peck, SET Fire Protection >> Skype +1(202)407-9079 >> Cambodia +855(0)78700407 >> >>> On Mar 13, 2014, at 10:41 PM, Brad Casterline <[email protected]> >>> wrote: >>> >>> My confidence level is a bit low and I would appreciate a boost: >>> >>> I'm hanging 1" thru 2" pipe at center of 19" below smooth concrete, >>> using drop-in anchors. Elevation-wise this puts me center 5" above >>> finished ceiling. >>> >>> I'm using 2-pc deep escutcheon. >>> >>> For simplicity I'm thinking 3/8x18" A.T.R. and 5" drops should work? >>> >>> >>> >>> Thanks, >>> >>> Brad >>> >>> _______________________________________________ >>> Sprinklerforum mailing list >>> [email protected] >>> http://lists.firesprinkler.org/listinfo.cgi/sprinklerforum-firesprink >>> l >>> er.org >> _______________________________________________ >> Sprinklerforum mailing list >> [email protected] >> http://lists.firesprinkler.org/listinfo.cgi/sprinklerforum-firesprinkl >> er.org _______________________________________________ >> Sprinklerforum mailing list >> [email protected] >> http://lists.firesprinkler.org/listinfo.cgi/sprinklerforum-firesprinkl >> er.org > _______________________________________________ > Sprinklerforum mailing list > [email protected] > http://lists.firesprinkler.org/listinfo.cgi/sprinklerforum-firesprinkler.org > _______________________________________________ > Sprinklerforum mailing list > [email protected] > http://lists.firesprinkler.org/listinfo.cgi/sprinklerforum-firesprinkler.org _______________________________________________ Sprinklerforum mailing list [email protected] http://lists.firesprinkler.org/listinfo.cgi/sprinklerforum-firesprinkler.org
