Hi guys. I already try the DMZ-Plus stuff, but look what i need to do, and after this, if i reboot my pfsense i need to do this again:
1; Disable DHCP server in my pfsense. 2; Put my WAN nic in DHCP mode. 3; Enable DHCP Server inside 2WIRE 4; Detect inside 2WIRE my PFsense-WAN 5; Put my PFsenseWAN in DMZPlus 6; Disable 2WIRE dhcp server 7; Enable DHCP server inside PFsenseLAN 8; After this i can use PFsense. But if for some reasons i reboot my pfsense, a lost everything, i need to do this again, is very exhausted. Now, another thing, look this is my small network: DSL <-- | | --------------------- ---------------------------- | | <-----PfsenseWAN--- | PFsense Box | <--- | 2WIRE | <-----LAN Switch---- --------------------------- | --------------------- | | PfsenseLAN | | | | | --------------------------- | | |--->| | <--| Internet | LAN Switch | --------------------------- <-----> Clients LAN Now why this settings??? 1; If i disconnect my 2WIRE from my switch, i lost all communication from my LAN, i couldn't access 2WIRE settings inside my LAN. 2; " , none of my clients could access Internet. I was trying to access my ISP from pfsense, i setup my WAN for PPPoE, all the settings like before, but pfsense cannot negotiated with ISP, i still don't now why, looks like 2WIRE doesn't want to let other device handled the connection. Now i need to check about the bridge mode see how it works. I will let u know guys, thanks for your help!!! 2007/9/3, Mike <[EMAIL PROTECTED]>: > > Alberto Moreno wrote: > > > > Hi people. > > > > This week my ISP told me that i need to change my old modem: DSL modem > > speedstream 5400, just a modem. My LAN was behind pfsense, DHCP, one vpn > > to my office, it was very beautiful. Some times i just connect my box > > and i was at work, didn't need to get there. > > > > Now, i have this 2wire Modem+Router(Model 2701HG-T), which if came > > with built-in Firewall, wireless, and other cool stuff for someone with > > no acknowledge of pfsense could say, this is great!!! > > > > Now i don't how to hell i will have my old settings, i cannot disable > > the firewall from that device, i cannot access my office from my LAN > > clients, the only one who could access my office is the pfsense box, > > because i enable some rule to the 2wire firewall, but any of my clients > > can. > > > > I'm lost, i don't know how is the gateway now or which one i chose? > > What about my WAN interface? I try to connect my wan interface but i > > don't get any answer from my ISP. > > > > I disable the DHCP server from the device, but right now my Gateway > > is 2wire, what can i do to bring everything to normal? do i need tot add > > each rule to my LAN and NAT or forward to my 2wire gateway? > > > > Someone could point me, what i need to do, or help me understand my > > case and help me find some path to this? > > > > Thanks all for your time. > > > > P.S. Running pfsense 1.0.1 Release. > > > > -- > > LIving the dream... > > I have the same gateway, and I just set the PFsense box in DMZ plus mode > (in the 2wire gateway) and specified that it gets the external IP from > my ISP. I am thinking that the 2wire's allow for proprietary firmware/ > software for each ISP though, so this may not work for you. When you > attempt to log in, do you use the http://<gateway address>? The address > you type in here is found in your PFsense WAN gateway. After you have > made the changes in your 2wire, you will need to reboot the pfsense box. > > Mike > > --------------------------------------------------------------------- > To unsubscribe, e-mail: [EMAIL PROTECTED] > For additional commands, e-mail: [EMAIL PROTECTED] > > -- LIving the dream...