Hi Stanislaw,
i bought a "new" AT-AR215 at eBay. This one works nearly great with
your driver. There seems to be little problem with firmware uploading on
slower systems (like my old PII300):
Aug 30 07:48:19 gigabyte kernel: usb 1-1: new full speed USB device
using uhci_hcd and address 3
Aug 30 07:48:19 gigabyte kernel: usb 1-1: [ueagle-atm] ADSL device
founded vid (0X1110) pid (0X9010)
Aug 30 07:48:19 gigabyte kernel: usb 1-1: reset full speed USB device
using uhci_hcd and address 3
Aug 30 07:48:19 gigabyte kernel: usb 1-1: [ueagle-atm] pre-firmware
device, uploading firmware
Aug 30 07:48:22 gigabyte kernel: usb 1-1: [ueagle-atm] firmware uploaded
Aug 30 07:48:22 gigabyte kernel: usb 1-1: USB disconnect, address 3
Aug 30 07:48:25 gigabyte kernel: usb 1-1: new full speed USB device
using uhci_hcd and address 4
Aug 30 07:48:25 gigabyte kernel: usb 1-1: [ueagle-atm] ADSL device
founded vid (0X1110) pid (0X900F)
Aug 30 07:48:25 gigabyte kernel: usb 1-1: reset full speed USB device
using uhci_hcd and address 4
Aug 30 07:48:25 gigabyte kernel: usb 1-1: [ueagle-atm] using iso mode
Aug 30 07:48:25 gigabyte kernel: usb 1-1: [ueagle-atm] (re)booting started
Aug 30 07:48:25 gigabyte kernel: usb 1-1: [ueagle-atm] created proc
entry at: /proc/driver/ueagle-atm/001-004
Aug 30 07:48:27 gigabyte kernel: usb 1-1: [ueagle-atm] (re)booting started
Aug 30 07:48:28 gigabyte kernel: usb 1-1: [UEAGLE-ATM] wrong intr
Aug 30 07:48:30 gigabyte kernel: usb 1-1: [ueagle-atm] (re)booting started
Aug 30 07:48:31 gigabyte kernel: fw_register_class_device:
class_device_register failed
Aug 30 07:48:32 gigabyte kernel: fw_register_class_device:
class_device_register failed
Aug 30 07:48:32 gigabyte kernel: usb 1-1: [UEAGLE-ATM] requesting
firmware ueagle-atm/DSPei.bin failed with error -17
Aug 30 07:48:34 gigabyte kernel: usb 1-1: [UEAGLE-ATM] uea_intr() failed
with -84
HERE I PLUGGED OUT THE MODEM!
Aug 30 07:48:35 gigabyte kernel: usb 1-1: USB disconnect, address 4
Aug 30 07:48:42 gigabyte kernel: usb 1-1: [UEAGLE-ATM] usb_control_msg
error -19
Aug 30 07:48:42 gigabyte kernel: usb 1-1: [UEAGLE-ATM] writing cmv
failed with error -19
Aug 30 07:48:43 gigabyte kernel: usb 1-1: [ueagle-atm] kthread finish
with status -19
Aug 30 07:48:43 gigabyte kernel: usb 1-1: [UEAGLE-ATM] usb_control_msg
error -19
Aug 30 07:48:43 gigabyte kernel: usb 1-1: [ueagle-atm] ADSL device removed
Sometimes i've got this messages on my PIII1000 too, but after changing
ACK_TIMEOUT to msecs_to_jiffies(1500) in ueagle-atm.h it finally works
fine! I used the patch from "2005-07-25 20:19:25" against vanilla
2.6.13 (final) {ohci-hcd, preemption (low latency), big kernel lock and
timer frequency of 250Hz}
Bjoern Schmidt schrieb:
>>Maybe using
>>http://castet.matthieu.free.fr/eagle/release/ueagle-atm-1.0a.tar.gz
>>instead of kernel patch help (at least debug module parameter should work
>>there,
>>to make it work in patch you need add "#define DEBUG 1" at the beginning of
>>ueagle-atm.c).
>>It seems that is rather usb_firmware/CMV/DSP or usb bus problem.
>>Did you use eagle-usb driver, if yes, you can make
>>CMV and DSP firmware from files with do you use with eagle-usb.
>
>
> yes but i got similar errors with this driver...
>
>
>>If not, hmm... there is no much choice between CMV files for ISDN
>>and may by you need add some special options by self, what's your ISP?
>
>
> My ISP is the German Telekom (vpi 1, vci 20). Unfortunately i am not
> (yet) very experienced with ATM, therefore i dont know what options to
> add... :(
I also had to change vci to 32...
--
Greetings
Bjoern Schmidt
