All right, now I have an LC III logic board in it (after a little head scratching to figure out why it wouldn't boot—dead battery, replaced with the LC II board's batt), and it's still saying it can't find an SCSI device with the ELS drive in.
I just found out that the LPS drive is missing its terminating resistors, and it needs 3 rather than 2 like the ELS. Does anyone know if it's possible to make these resistors DIY? On May 25, 12:00 pm, Austin Leeds <[email protected]> wrote: > OK, a little more specific info: > > Original drive: Quantum ProDrive ELS 85 > Shttp://stason.org/TULARC/pc/hard-drives-hdd/quantum/PRODRIVE-ELS-85-S... > > LaCie external drive: Quantum ProDrive LPS 240 > Shttp://stason.org/TULARC/pc/hard-drives-hdd/quantum/PRODRIVE-LPS-240-... > > As you can see, when I tried to use the ELS' terminating resistors on > the LPS, they obviously didn't work. Which leads me to believe the ELS > went bad or has stiction, and the LPS needs the correct terminating > resistors. Am I on the right track? > > On May 23, 2:52 pm, Todd - <[email protected]> wrote: > > > > > The LaCie SCSI drive may not be terminated properly for the LCII or might > > need a patched version of Apple Drive Setup utility to format a non branded > > Apple drive. > > > Todd M > > > On Mon, May 23, 2011 at 1:26 PM, Todd Brayer <[email protected]> wrote: > > > Just as a "why not" sort of thing, disconnect and reconnect the HDD. > > > Maybe a pin got loose just from time and whatnot. > > > > You can sometimes tell when an HDD is about to die. Is there any > > > unusual clicking noises? When my LCII was about to have it's > > > HDD die it started screeching like a tea kettle. > > > > Todd Brayer > > > [email protected] > > > > On Mon, May 23, 2011 at 3:23 PM, Alex Barnes <[email protected]> wrote: > > > > Try the drive in another computer. If it doesn't work it may have, as we > > > say in Texas, "Dunupindied". > > > > On May 23, 2011, at 1:16 PM, Todd Brayer wrote: > > > > >> The duster might have done something on the motherboard (always use > > > >> canned air to dust electronics), though I doubt it. > > > > >> Todd Brayer > > > >> [email protected] > > > > > -- > > > > ----- > > > > You received this message because you are a member of the Vintage Macs > > > group. > > > > The list FAQ is athttp://lowendmac.com/lists/vintagemacs.shtmlandour > > > netiquette guide is athttp://www.lowendmac.com/lists/netiquette.shtml > > > > To post to this group, send email to [email protected] > > > > To leave this group, send email to > > > [email protected] > > > > For more options, visit this group at > > >http://groups.google.com/group/vintage-macs > > > > > Support for older Macs:http://lowendmac.com/services/ > > > > -- > > > ----- > > > You received this message because you are a member of the Vintage Macs > > > group. > > > The list FAQ is athttp://lowendmac.com/lists/vintagemacs.shtmlandour > > > netiquette guide is athttp://www.lowendmac.com/lists/netiquette.shtml > > > To post to this group, send email to [email protected] > > > To leave this group, send email to > > > [email protected] > > > For more options, visit this group at > > >http://groups.google.com/group/vintage-macs > > > > Support for older Macs:http://lowendmac.com/services/ -- ----- You received this message because you are a member of the Vintage Macs group. The list FAQ is at http://lowendmac.com/lists/vintagemacs.shtml and our netiquette guide is at http://www.lowendmac.com/lists/netiquette.shtml To post to this group, send email to [email protected] To leave this group, send email to [email protected] For more options, visit this group at http://groups.google.com/group/vintage-macs Support for older Macs: http://lowendmac.com/services/
