Just a quick note on the enhanced PTP mode of operation - You will see lower latency in most deployments as compared to the TDD & Flex mode of operation. However, in high interference coupled with long distance environments the flexible mode will do better in terms of tput. At this time, this is per design but we will be addressing and incorporating some of the good stuff from our TDD/Flex mode of operation into the enhanced PTP to bring back the tput in the above conditions. Please note that we are also working on a 2.5ms frame to reduce latency in the PMP mode of operation.
Thanks Sakid From: Mathew Howard <mhoward...@gmail.com<mailto:mhoward...@gmail.com>> Reply-To: "af@afmug.com<mailto:af@afmug.com>" <af@afmug.com<mailto:af@afmug.com>> Date: Wednesday, March 11, 2015 at 2:56 AM To: "af@afmug.com<mailto:af@afmug.com>" <af@afmug.com<mailto:af@afmug.com>> Subject: Re: [AFMUG] ePMP Release 2.4 is Now Available I wonder if it doesn't handle interference as well in some cases, or something like that... it'll be interesting to see what it does on other links. On Tue, Mar 10, 2015 at 6:59 PM, John Woodfield <john.woodfi...@jwcn.biz<mailto:john.woodfi...@jwcn.biz>> wrote: Interesting. I used the Cambium link tester and followed up with Mikrotik. Weird John Woodfield, President Delmarva WiFi Inc. 410-870-WiFi -----Original Message----- From: "Mathew Howard" <mhoward...@gmail.com<mailto:mhoward...@gmail.com>> Sent: Tuesday, March 10, 2015 5:42pm To: "af" <af@afmug.com<mailto:af@afmug.com>> Subject: Re: [AFMUG] ePMP Release 2.4 is Now Available I did run a test before and after between the Mikrotik routers at each end of the link, it was averaging just over 50Mbps before and after - this was using a 20mhz channel with a fairly high noise floor, which is unfortunately the best I can do without shutting down some other stuff on these towers. On Tue, Mar 10, 2015 at 3:58 PM, John Woodfield <john.woodfi...@jwcn.biz<mailto:john.woodfi...@jwcn.biz>> wrote: Have you run before and after link tests within the software? John Woodfield, President Delmarva WiFi Inc. 410-870-WiFi -----Original Message----- From: "Mathew Howard" <mhoward...@gmail.com<mailto:mhoward...@gmail.com>> Sent: Tuesday, March 10, 2015 1:18pm To: "af" <af@afmug.com<mailto:af@afmug.com>> Subject: Re: [AFMUG] ePMP Release 2.4 is Now Available I upgraded a link to 2.4, and I'm not really seeing any difference in throughput with the ePTP mode... it's slightly better, if anything. latency dropped from 6-7ms to 1-2ms (with no load on the link). This link isn't actually in use, since it was replaced with a Mimosa link, so it's not really the best test... but it's also far from low noise, since both ends of the link are within a couple of the Mimosa radios, and on the same path. On Tue, Mar 10, 2015 at 6:06 AM, John Woodfield <john.woodfi...@jwcn.biz<mailto:john.woodfi...@jwcn.biz>> wrote: The PTP mode has been there. It allows to turn about the power to 30dbm in 5.8. I had a radio running at 30dbm and it would crap out within 12 hours - ethernet port would quit working. I dropped it to 28dbm and it works fine YMMV. The new PTP master/slave mode was supposed to cut latency - from what I saw it only cut it by about 5ms and the performance cut was dramatic. John Woodfield, President Delmarva WiFi Inc. 410-870-WiFi -----Original Message----- From: "George Skorup (Cyber Broadcasting)" <geo...@cbcast.com<mailto:geo...@cbcast.com>> Sent: Tuesday, March 10, 2015 2:57am To: af@afmug.com<mailto:af@afmug.com> Subject: Re: [AFMUG] ePMP Release 2.4 is Now Available If that's the case, then that's not cool. I see there's two PTP modes though. One is ePTP Master and Slave. The other is just PTP. Look like the PTP mode requires fixed distance settings at both ends? And ePTP mode does auto-ranging like Canopy BHM/BHSs perhaps? When are we going to get 2.5ms framing to sync with Canopy? I see we can now turn on the aux port PoE output and it'll power another ePMP or Canopy SM. PTP from a customer's barn to their house got easier. But that additional 20ms of latency is not so good, so hopefully PTP mode for a 1000' link works. On 3/9/2015 8:36 PM, John Woodfield wrote: This new mode of operation increases retransmits and cuts throughput in half in environments with any noise from what I've seen so far. John Woodfield, President Delmarva WiFi Inc. 410-870-WiFi -----Original Message----- From: "Mike Hammett" <af...@ics-il.net><mailto:af...@ics-il.net> Sent: Monday, March 9, 2015 3:38pm To: af@afmug.com<mailto:af@afmug.com> Subject: Re: [AFMUG] ePMP Release 2.4 is Now Available * New ePTP mode of operation: The release introduces a new mode of operation for point-to-point configuration providing significantly lower latency than other modes. Not available for DFS bands. ----- Mike Hammett Intelligent Computing Solutions http://www.ics-il.com [http://www.ics-il.com/images/fbicon.png]<https://www.facebook.com/ICSIL>[http://www.ics-il.com/images/googleicon.png]<https://plus.google.com/+IntelligentComputingSolutionsDeKalb>[http://www.ics-il.com/images/linkedinicon.png]<https://www.linkedin.com/company/intelligent-computing-solutions>[http://www.ics-il.com/images/twittericon.png]<https://twitter.com/ICSIL> ________________________________ From: "Ray Savich" <ray.sav...@cambiumnetworks.com><mailto:ray.sav...@cambiumnetworks.com> To: "af@afmug.com"<mailto:af@afmug.com><af@afmug.com><mailto:af@afmug.com> Sent: Monday, March 9, 2015 1:33:08 PM Subject: [AFMUG] ePMP Release 2.4 is Now Available ePMP Release 2.4 includes new enhancements to eFortify(tm) and eCommand(tm). Check out the details at http://bit.ly/1BYo2ja Ray Join the Conversation Cambium Networks Community Forum<http://community.cambiumnetworks.com/>