There are usually only 2 types of NonPen's that we use, either a 6' mast
sturdy enough to put a reflector dish on (Flat roof that has a 4'
kneewall around the roof, very common in our area) or something in the
20-30' range. We don't usually have a need for something in between.
Definitely have the need to slightly level the mount in some way.
It would also be really cool to come up with a way to get ballast to the
roof. Maybe a smaller and lighter version of one of these that only
needs to do 40 or 50lb at a time.
http://www.garlockequip.com/garlock-hand-power-hoist-300-lb/ Run a
Garden hose up to fill up some plastic water tanks for the ballast.
Obviously, this would only be used when you need to lift more than like
10 blocks to the roof. Bonus points if you could hook a drill up to it
to make it a powered lift.
On 1/9/2016 1:09 PM, Ken Hohhof wrote:
There’s already one that tilts, although the mast appears to be a
non-standard size if you want to put a reflector dish directly on the top.
http://www.balticnetworks.com/maxxwave-adjustable-2in-non-penetrating-roof-mount.html
Lots of other designs out there including pitched roof mounts that
take J-pipes.
http://www.3starinc.com/non-pen_mounts_2.html
*From:* ch...@wbmfg.com <mailto:ch...@wbmfg.com>
*Sent:* Saturday, January 09, 2016 12:45 PM
*To:* af@afmug.com <mailto:af@afmug.com>
*Subject:* Re: [AFMUG] Non penetrating mounts
So you would want the mast holder to have U bolts? Then you supply
your own mast?
I looked at the wall brace, I don’t remember what the issue was,
probably could not build it for a competitive price. I know I played
with the design a bit.
*From:* Jaime Solorza <mailto:losguyswirel...@gmail.com>
*Sent:* Saturday, January 9, 2016 11:36 AM
*To:* Animal Farm <mailto:af@afmug.com>
*Subject:* Re: [AFMUG] Non penetrating mounts
OK...here goes...make the mast holder brace like ones on J arms with
degrees on it. Make wide enough to hold different diameter pipe. The
screw and bolt serves two purposes... hinge and anti rotation. So now
you can tilt mast as needed. The yoke will be wide enough to
accommodate different size pipe and by using same tightening method
but with longer screws you can adjust to position. This will work
whether support base is traditional or hinged. Easy enough to make
telescoping arms if you have a machine shop. I waive my consulting
fee for the good of the list. BTW..hey Chuck... you ever make that
wall brace idea I sent you?
On Jan 9, 2016 11:26 AM, "Joshaven Mailing Lists" <lis...@joshaven.com
<mailto:lis...@joshaven.com>> wrote:
How about Lego® style where you can add/remove parts to make it
work for larger & smaller setups…
Sincerely,
Joshaven Potter
Google Hangouts: j...@g2wireless.co <mailto:j...@g2wireless.co>
Cell & SMS: 1-517-607-9370 <tel:1-517-607-9370>
supp...@joshaven.com <mailto:supp...@joshaven.com>
On Jan 9, 2016, at 1:05 PM, Chuck McCown <ch...@wbmfg.com
<mailto:ch...@wbmfg.com>> wrote:
I get constantly asked to do a non penetrating mount. I have
always resisted because there are a ton of them out there
already. But I get almost daily searches for this term on my
website. It appears folks presume I have one.
If I did one, I would like to have some feature or quality that
differentiates it from the rest. Perhaps a unit that can be
locked or hinged for flat or peak mounts.
Maybe one with hinged legs that give it a wider footprint using
greater leverage so you don’t need as many concrete blocks.
I dunno, any ideas?