Have you tried eptp master slave mode? On Aug 20, 2016 1:07 PM, <[email protected]> wrote:
> Are you using the same SM for all of your tests? > > *From:* Jordan Gregory <[email protected]> > *Sent:* Saturday, August 20, 2016 12:43 PM > *To:* [email protected] > *Subject:* Re: [AFMUG] New to list - issues (i think) with ePMP 2.4 > > So here are the things i've tried. > > Both my main Netonix Switch and the microtik switches has flow control > turned on. I disabled it and actually, if possible, the speed got worse. So > i re-enabled it. > > I'm still unable to pass more the 3Mbps anywhere though. > > I've been able to replicate this on every sector now. It has to be > something upstream from the access points, but I'm just not sure where to > look at this point. > > Thank You, > > Jordan Gregory > Founder / CEO > Hive Wireless, LLC > > On Thu, Aug 18, 2016 at 10:50 PM, Jordan Gregory < > [email protected]> wrote: > >> Tik switch at the tower had flow control enabled on all ports. I have >> disabled it now. Customer is asleep now i'm sure, so I can't have them >> check. But I'll know more in the morning. This was happening on all SMs >> though, so I may fire one up just to see. >> >> >> >> Thank You, >> >> Jordan Gregory >> Founder / CEO >> Hive Wireless, LLC >> >> On Thu, Aug 18, 2016 at 10:46 PM, Jordan Gregory < >> [email protected]> wrote: >> >>> They aren't airfiber, they are Mimosa B5s >>> >>> Microtik routers/switches. >>> >>> I didn't enable flow control, but i'll double check >>> >>> Thank You, >>> >>> Jordan Gregory >>> Founder / CEO >>> Hive Wireless, LLC >>> >>> On Thu, Aug 18, 2016 at 10:43 PM, George Skorup <[email protected]> >>> wrote: >>> >>>> What is all of the equipment involved? Have you looked for CRC or FCS >>>> errors on any ethernet links? Unfortunately, the ePMP gear does not have >>>> ethernet CRC errors stats. What about flow control on your GigE interfaces? >>>> >>>> Have you ran iperf from behind the SM all the way through to your >>>> router? >>>> >>>> You say 750Mbps. Are they AirFiber radios? Flow control is what comes >>>> to my mind there. If you have flow control enabled anywhere, turn it off >>>> and see if end-user speed increases. We don't use it because pause frames >>>> cause jitter for VoIP. >>>> >>>> On 8/18/2016 10:34 PM, Jordan Gregory wrote: >>>> >>>> Everyone, >>>> >>>> I enabled the MIR profiles and set the one I am talking about to >>>> 25000/5000, the link test shows this speed perfectly, except when we do a >>>> speedtest via speedof.me or speedtest.net or anything really, it's >>>> only showing 3Mbps. >>>> >>>> I have a cambium support ticket open, but that may take a while. >>>> >>>> I've dug through every setting I can find and can't see anything that >>>> would be causing this. >>>> >>>> Here is the generic layout of my network: >>>> >>>> SM --><-- AP --> L3 Switch --> BH Radio --> <-- BH Radio --> Switch --> >>>> Router --> Internet >>>> >>>> I've tested the speed (iperf) all the way from my router to my l3 >>>> swtich at the tower and I'm getting roughtly 750Mbps avg to the l3 switch. >>>> I've tested throughput on the switch as well and I was easily passing 5Gbps >>>> through it. >>>> >>>> I've seen no speed mismatch errors anywhere on the network. >>>> >>>> Thank You, >>>> >>>> Jordan Gregory >>>> Founder / CEO >>>> Hive Wireless, LLC >>>> >>>> On Thu, Aug 18, 2016 at 11:05 AM, Kerry <[email protected]> wrote: >>>> >>>>> Here's a couple things to check, >>>>> >>>>> Check the ap, is MIR under QOS enabled? if so, there should be an >>>>> entry under monitor->wireless for the sm showing the rate the sm is >>>>> 'queued' at. >>>>> >>>>> The wireless link test will only show it passing roughly what it is >>>>> queued at. Also, check the MCS column. If it;s a good link it will be at >>>>> the max Rate setting configured >>>>> >>>>> under the radio config of the ap >>>>> >>>>> >>>>> >>>>> On 8/18/2016 11:46 AM, Jordan Gregory wrote: >>>>> >>>>> Good day list, >>>>> >>>>> I have a Force 200 operating at very good signal levels but for some >>>>> reason, I can seem to get any more than 3Mbps out of the connection. >>>>> >>>>> Did i miss a setting somewhere? >>>>> >>>>> Backstory: Brand new wisp >>>>> >>>>> Thank You, >>>>> >>>>> Jordan Gregory >>>>> Founder / CEO >>>>> Hive Wireless, LLC >>>>> >>>>> >>>>> >>>> >>>> >>>> >>> >> >> > >
