getting its source maybe give you some help :)

Mark Co-Dyre wrote:
> Thanks Richard,
>
> I'm going to try it when I get home.
> Quick question
> I used Haret version 0.3.2(with usart support; fisherss ver), 0.3.4
> and 0.3.6. When using haret 0.3.4 I get a boot screen that shows a
> penguin. But, with the others I get nothing other than the Haret
> screen. Confused... could someone enlighten me on where this little
> penguin is coming from?
>
> Regards...
>
> Mark
>
> On 9/8/05, *Richard Bateman* <[EMAIL PROTECTED]
> <mailto:[EMAIL PROTECTED]>> wrote:
>
>     A few things:
>
>     1. you must be using fisherss' haret, as it initializes the serial
>     port
>     2. here is my default.txt:
>
>     print "Setting GPIOs for serial port..."
>     set GAFR(34) 1
>     set GAFR(35) 1
>     set GAFR(37) 1
>     set GAFR(39) 2
>     set GAFR(40) 2
>     set GAFR(41) 2
>     set GPDR(34) 0
>     set GPDR(35) 0
>     set GPDR(37) 0
>     set GPLR(34) 1
>     set GPLR(35) 1
>     set GPLR(37) 1
>     set GPLR(39) 1
>
>     set kernel "zImage"
>     set initrd "initrd"
>     set mtype 740
>     set cmdline "root=/dev/ram0 rw ramdisk_size=16384 keepinitrd
>     init=/linuxrc console=tty0 console=ttyS0,115200n8"
>     boot
>
>     this works for me.
>
>     When you wire up the serial cable, the pin that reads +- 3v with
>     ground
>     on a voltmeter is the tx pin from the x50 itself. it should be labeled
>     which pin this should go to on the max232 chip. On the pc side, it's
>     +9v, and the +9v from the max232 that comes from the max232 should
>     go to
>     the RX pin on your computer.
>
>     Similarly, the +9v from your computer rs232 cable is the tx from the
>     computer, and should go through the max232 to the rx on the other
>     side.
>
>     if you aren't using fisherss' haret, however, it probably won't work,
>     because his haret is modified to initialize the serial port.
>
>     Richard
>
>     Mark Co-Dyre wrote:
>
>     > Hello all,
>     >
>     > I'm new to this project and would greatly appreciate a couple of
>     > pointers on how to get the serial port console working on the
>     x50v. I
>     > got the penguin to display itself and the thermometer in the graphic
>     > to rise (freezes after the penguin eyes go all funny). But, I can't
>     > seem to get any output from the serial cable. When I scope out the
>     > Serial TX pin on the my Dell I seem to get a partial
>     initialization of
>     > the port because It changes state from a 0 to a 1 right after
>     starting
>     > Haret and then pressing run. Linux never actually boots. I'm just
>     > hoping to get some more info to make it easier to debug what is
>     > actually happening.
>     >
>     > I've built the serial cable that fisher had so kindly documented.
>     > Although in the documentation, I do suspect that the pin outs
>     for Dell
>     > pin number 10-Rx(dell in) and 11-TX(dell out) are reversed on the
>     > practical serial cable making method; I think it should be 11-Rx,
>     > 10-TX. if someone has a cable handy could they double check this
>     for
>     > me? Fisherss am I correct? For now I just hook a scope probe up to
>     > both the pins (10 and 11) and try to make data come out of
>     either or.
>     >
>     > Did you have to modify the haret program to get the serial port
>     of the
>     > dell up and running? Or will just modifying General Purpose I/O
>     > Alternate Function Select Registers by adding the appropriate
>     info the
>     > default.txt file work just fine (set GAFR(34) 1 and so on)
>     >
>     > I Hope that makes sense... any help would be greatly appreciated...
>     >
>     > Regards..
>     >
>     > Mark
>     >
>
>     --
>     _______________________________________________
>     Aximx50-port mailing list
>     [email protected] <mailto:[email protected]>
>     https://www.handhelds.org/mailman/listinfo/aximx50-port
>
>
-- 
_______________________________________________
Aximx50-port mailing list
[email protected]
https://www.handhelds.org/mailman/listinfo/aximx50-port

Reply via email to