Fisherss, do you still know what you've changed with the haret program
exactly? Maybe we can sync that with the latest version, or with the
version with the cool penguin :-)
And for X50V, we should use the same version, right? And the same default.txt?

And another question about the kernel: Did you have to change anything
with the kernel source? For X50v, I think Richard has changed at least
the vsfb driver, is that right? Do the notes from you about building a
new kernel still last?

On 9/9/05, Fisherss <[EMAIL PROTECTED]> wrote:
> getting its source maybe give you some help :)
> 
> Mark Co-Dyre wrote:
> > Thanks Richard,
> >
> > I'm going to try it when I get home.
> > Quick question
> > I used Haret version 0.3.2(with usart support; fisherss ver), 0.3.4
> > and 0.3.6. When using haret 0.3.4 I get a boot screen that shows a
> > penguin. But, with the others I get nothing other than the Haret
> > screen. Confused... could someone enlighten me on where this little
> > penguin is coming from?
> >
> > Regards...
> >
> > Mark
> >
> > On 9/8/05, *Richard Bateman* <[EMAIL PROTECTED]
> > <mailto:[EMAIL PROTECTED]>> wrote:
> >
> >     A few things:
> >
> >     1. you must be using fisherss' haret, as it initializes the serial
> >     port
> >     2. here is my default.txt:
> >
> >     print "Setting GPIOs for serial port..."
> >     set GAFR(34) 1
> >     set GAFR(35) 1
> >     set GAFR(37) 1
> >     set GAFR(39) 2
> >     set GAFR(40) 2
> >     set GAFR(41) 2
> >     set GPDR(34) 0
> >     set GPDR(35) 0
> >     set GPDR(37) 0
> >     set GPLR(34) 1
> >     set GPLR(35) 1
> >     set GPLR(37) 1
> >     set GPLR(39) 1
> >
> >     set kernel "zImage"
> >     set initrd "initrd"
> >     set mtype 740
> >     set cmdline "root=/dev/ram0 rw ramdisk_size=16384 keepinitrd
> >     init=/linuxrc console=tty0 console=ttyS0,115200n8"
> >     boot
> >
> >     this works for me.
> >
> >     When you wire up the serial cable, the pin that reads +- 3v with
> >     ground
> >     on a voltmeter is the tx pin from the x50 itself. it should be labeled
> >     which pin this should go to on the max232 chip. On the pc side, it's
> >     +9v, and the +9v from the max232 that comes from the max232 should
> >     go to
> >     the RX pin on your computer.
> >
> >     Similarly, the +9v from your computer rs232 cable is the tx from the
> >     computer, and should go through the max232 to the rx on the other
> >     side.
> >
> >     if you aren't using fisherss' haret, however, it probably won't work,
> >     because his haret is modified to initialize the serial port.
> >
> >     Richard
> >
> >     Mark Co-Dyre wrote:
> >
> >     > Hello all,
> >     >
> >     > I'm new to this project and would greatly appreciate a couple of
> >     > pointers on how to get the serial port console working on the
> >     x50v. I
> >     > got the penguin to display itself and the thermometer in the graphic
> >     > to rise (freezes after the penguin eyes go all funny). But, I can't
> >     > seem to get any output from the serial cable. When I scope out the
> >     > Serial TX pin on the my Dell I seem to get a partial
> >     initialization of
> >     > the port because It changes state from a 0 to a 1 right after
> >     starting
> >     > Haret and then pressing run. Linux never actually boots. I'm just
> >     > hoping to get some more info to make it easier to debug what is
> >     > actually happening.
> >     >
> >     > I've built the serial cable that fisher had so kindly documented.
> >     > Although in the documentation, I do suspect that the pin outs
> >     for Dell
> >     > pin number 10-Rx(dell in) and 11-TX(dell out) are reversed on the
> >     > practical serial cable making method; I think it should be 11-Rx,
> >     > 10-TX. if someone has a cable handy could they double check this
> >     for
> >     > me? Fisherss am I correct? For now I just hook a scope probe up to
> >     > both the pins (10 and 11) and try to make data come out of
> >     either or.
> >     >
> >     > Did you have to modify the haret program to get the serial port
> >     of the
> >     > dell up and running? Or will just modifying General Purpose I/O
> >     > Alternate Function Select Registers by adding the appropriate
> >     info the
> >     > default.txt file work just fine (set GAFR(34) 1 and so on)
> >     >
> >     > I Hope that makes sense... any help would be greatly appreciated...
> >     >
> >     > Regards..
> >     >
> >     > Mark
> >     >
> >
> >     --
> >     _______________________________________________
> >     Aximx50-port mailing list
> >     [email protected] <mailto:[email protected]>
> >     https://www.handhelds.org/mailman/listinfo/aximx50-port
> >
> >
> --
> _______________________________________________
> Aximx50-port mailing list
> [email protected]
> https://www.handhelds.org/mailman/listinfo/aximx50-port
>
--
_______________________________________________
Aximx50-port mailing list
[email protected]
https://www.handhelds.org/mailman/listinfo/aximx50-port

Reply via email to