Yup, i tried Jedi's way, it says "there's no such device or>> address" , well, off to work, this night perhaps i'll be fresh and see what i'm doing wrong, thanks :)
Fisherss wrote:
"No such file or directory" means that you didn't format your SD card correctly. The device files are there, you just can't mount it. I recommend you to follow JeDi's way to get it working. Have you tried it ?Angel Sánchez Morales wrote:Hmm... i'm stupid or still asleep xD I only had to put ls /dev -R on the linuxrc script :p /dev looks like: /dev: console hda hda2 null ttyS0 ttyS2 fb0 hda1 mmc tty ttyS1 vc0 /dev/mmc: blk0 /dev/mmc/blk0: disc part1 part2 Trying to mount part2... And the screen turns nearly all white :/ I was using the x50v filesystem.Then using x50 filesystem i re-format the sd and doesn't load opie still :(The funny thing is that it says that there's no such device or address, but then when doing an ls it is there!I'm bored, I'll continue trying it at night... sigh... JeDi wrote:Yes! I've got it running! I modified linuxrc in the initrd, so it mounts /dev/mmc/blk0/part1 in stead of /dev/mmc/blk0/disc, so I could create a partition in the normal way and put the rootfs there. That did the trick! The touchscreen driver isn't working correctly though (on x50v that is). Shouldn't there be some sort of alignment screen first in Opie? Anyway, the screen coordinates aren't correct, so I can't click much of the icons. I'll have a look at the touchscreen driver in the sources (it's there, right?). But anyway, I'm very happy I can finally see some decent result. Thanks a lot everybody! Greetz, JeDi On 1/4/06, Angel Sánchez Morales <[EMAIL PROTECTED]> wrote:Woho!!! woho!!! I got more output!!! :DAfter the Freeing init memory: 80K i can see this (the above seems to bethe same as before): open("/dev/mem"): No such file or directory open("/dev/mem"): No such file or directory Initial RAM Disk started ...mount: Mounting /dev/mmc/blk0/disc on /mnt/rootfs failed: No such deviceor address Failed to mount root filesystem, dropping to a shell Busybox v0.60.5 (2004.04.11-12:09+0000) Built-in shell (ash) Enter 'help' for a list of built-in commands. sh: can't access tty: job control turned off # If i use Fisherss' method to format the sd it makes an entire ext2partition on the sd, but then when using fdisk it doesn't recognizes anypartition and when you hit w (for writting the data to the medium) it tries to sync with the device and then it exits by itself, i should hit q to exit from fdisk. So i left the partition created with mke2fs /dev/sda and put all the filesystem there. I got the same output as before, and looking at it I noticed that it says that mmc0 doesn't have read-only access and makes it rw (mmc0: host does not support reading read-only switch. assuming write-enable.) and then i can see the line trying to mount mmc (mount: Mounting /dev/mmc/blk0/disc on /mnt/rootfs failed: No such device or address), perhaps in x50v we need to mount /dev/mmc0/blk0/disc? If i have time this night i'll try to modify the initrd to mount that device :) Fisherss wrote:I remember that the Chinese guy has mentioned this, use this line: set cmdline "root=/dev/ram0 rw ramdisk_size=12288 keepinitrd init=/linuxrc console=tty0" instead of this line : set cmdline "root=/dev/ram0 rw ramdisk_size=12288 keepinitrd init=/linuxrc console=tty0 console=ttyS0,115200n8 " Then you may get the output from linuxrc or other thing. JeDi wrote:On 1/4/06, Fisherss <[EMAIL PROTECTED]> wrote:The "echo" lines appear only through your serial console, not on thescreen. The size of fonts is suitable for x50, and I don't know what size x50v needs.It's in the post from the guy that got framebuffer working for x50v: "Graphics support->Console display driver support:enable VGA8X8 and VGA8x16" When these are enabled (the mini one can stay enabled too), the textis realy nicely readable on the x50v (kinda hard to read with the minifont on that resolution). Is there a way to put messages on screen in the linuxrc script? Would be great for us without a serial cable :-)I am uploading it. About the newest kernel, I have tried CVS version, but looks like something is aximx30.c file is incorrect, it cant passcompiling process.Thanks for uploading! As for the aximx30.c file not compiling, that's in the previously mentioned post too: [quote] f) modify aximx30.c to support new kernel: from kernel 2.6.13 ,the macros to setup machine descrtipion is delete from kernel source,so you should modify the endof aximx30.c as following: MACHINE_START(X30, "Dell Axim X30") #if 0 MAINTAINER("Giuseppe Zompatori, <[EMAIL PROTECTED]>") BOOT_MEM(0xa8000000, 0x40000000, io_p2v(0x40000000)) BOOT_PARAMS(0xa0000100) MAPIO(x30_map_io) INITIRQ(x30_init_irq) #endif .phys_ram = 0xa8000000, .phys_io = 0x40000000, .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc, .boot_params = 0xa0000100, .map_io = x30_map_io, .init_irq = x30_init_irq, .timer = &pxa_timer, .init_machine = x30_init, MACHINE_END [/quote] Thanks Fisherss and all the rest, for the great work you all put into this! Greetz and good luck, JeDi-- _______________________________________________ Aximx50-port mailing list [email protected] https://www.handhelds.org/mailman/listinfo/aximx50-port
-- _______________________________________________ Aximx50-port mailing list [email protected] https://www.handhelds.org/mailman/listinfo/aximx50-port
