Ahmed, Does the calling phone have the Long Distance Partition as part of it's CSS?
--- Ahmed Hamed <[EMAIL PROTECTED]> wrote: > > > ccievoice1, > > What if I don't have a CSS or a partition defined > anywhere?.... Not even an AAR CSS! > > Is it a requirement to have an AAR CSS defined? > > Thanks, > > AH > > > > --- On Mon, 6/16/08, ccievoice1 > <[EMAIL PROTECTED]> wrote: > > > From: ccievoice1 <[EMAIL PROTECTED]> > > Subject: Re: [OSL | CCIE_Voice] AAR Problem! > > To: [EMAIL PROTECTED], "OSL CCIE Voice Lab Exam" > <ccie_voice@onlinestudylist.com> > > Date: Monday, June 16, 2008, 1:26 PM > > Well, > > > > I will always check and verify the calling search > space and > > the partition. > > Also, I will make sure that I have the AAR Group, > AAR CSS > > and the External > > Phone Mask configured on my ip phones. Lets not > forget AAR > > Group and AAR CSS > > on the gateway as well. > > > > HTH > > > > On Mon, Jun 16, 2008 at 9:10 PM, Ahmed Hamed > > <[EMAIL PROTECTED]> wrote: > > > > > > > > > > > Hi ccievoice1, > > > > > > Thank you for your reply. > > > > > > > > > I dont's think there is a typo below, but > possibly > > a "mistake" :) > > > > > > so... > > > > > > HQ-AAR should have same prefix as original route > > pattern e.g. 91 and > > > 9.16175222XXX > > > > > > BUT I have it correct in the other way around > > > > > > i.e. > > > > > > Br1-AAR ..... prefix:91 with HQ-AAR > > > > > > and original route pattern is 9.12122221xxx > > > > > > Any clue? > > > > > > AH > > > > > > > > > --- On Mon, 6/16/08, ccievoice1 > > <[EMAIL PROTECTED]> wrote: > > > > > > > From: ccievoice1 <[EMAIL PROTECTED]> > > > > Subject: Re: [OSL | CCIE_Voice] AAR Problem! > > > > To: [EMAIL PROTECTED], "OSL CCIE Voice Lab > > Exam" < > > > ccie_voice@onlinestudylist.com> > > > > Date: Monday, June 16, 2008, 8:20 AM > > > > Hi, > > > > > > > > Not sure if it is typo error. You have AAR > prefix > > 9 with > > > > BR1 while your > > > > route pattern to BR1 is 916175222XXX > > > > > > > > IF it is not a typo, then with your AAR Prefix > + > > BR1 > > > > External Phone Mask = > > > > 96175222002 which didn't match your BR1 Route > > Pattern. > > > > > > > > Br1-AAR ..... prefix:91 with HQ-AAR > > > > HQ-AAR ..... *prefix: 9* with BR1-AAR > > > > > > > > HQ phone dn [1001, 2122221001] > > > > BR1 phone dn [2002, 6175222002] > > > > > > > > > > > > Route patterns configured: > > > > 9.12122221xxx > > > > 9.16175222xxx > > > > > > > > HTH > > > > > > > > On Mon, Jun 16, 2008 at 3:48 AM, Ahmed Hamed > > > > <[EMAIL PROTECTED]> wrote: > > > > > > > > > > > > > > > > > > > > > > > > Hi, > > > > > > > > > > I have a problem with AAR.. > > > > > > > > > > HQ phone is configured with location HQ-L > > > > > Br1 phone is configured with location BR1-L > > > > > > > > > > > > > > > AAR groups are configured as follows: > > > > > > > > > > Br1-AAR ..... prefix:91 with HQ-AAR > > > > > HQ-AAR ..... prefix: 9 with BR1-AAR > > > > > > > > > > HQ phone dn [1001, 2122221001] > > > > > BR1 phone dn [2002, 6175222002] > > > > > > > > > > > > > > > Route patterns configured: > > > > > 9.12122221xxx > > > > > 9.16175222xxx > > > > > > > > > > pointing to 6608 gw. > > > > > > > > > > Problem: Whenever I reduce location HQ-L, I > > try to > > > > reach destination > > > > > hqphone from BR1 phone, and I get a fast > > busy tone.. > > > > > > > > > > I am not sure where the problem is.. Could > > anyone give > > > > me a hint? > > > > > > > > > > Note: Under normal conditions, I can reach > > hqphone > > > > from Br1 phone thru 6608 > > > > > gw if I use hq phone's external mask as > > a > > > > destination.. > > > > > > > > > > > > > > > Thanks, > > > > > > > > > > AH > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > Jacob Owen CCIE #14063 (R&S, Service Provider), CCVP, CCDP