Put who on hold?
If you put PSTN on hold that would work fine but if you put IP phones of
other sites on Hold then they will not hear anything.
This is because IPsec limitations over VPN (this is also mentioned at
Proctor labs login page).
To check if your MOH is working fine then you can run the folliwng
commands and check the outputs.
These are the outputs I can see for my BR1 MOH:
BR1-RTR#sh ccm-manager mus
BR1-RTR#sh ccm-manager music-on-hold
Current active multicast sessions : 1
Multicast RTP port Packets Call Codec Incoming
Address number in/out id Interface
===================================================================
239.1.1.1 16384 433/433 69 g711ulaw Lo0
BR1-RTR#
BR1-RTR#
BR1-RTR#
BR1-RTR#debug eph
BR1-RTR#debug ephone moh
EPHONE music-on-hold debugging is enabled
BR1-RTR#
BR1-RTR#
Apr 18 00:01:32.241: MoH route If Loopback0 46 10.10.110.2 via 10.10.110.2
Apr 18 00:01:32.241: MoH route If Vlan240 ETHERNET 10.10.201.1 via ARP
BR1-RTR#
Apr 18 00:01:37.533: MoH route If Loopback0 46 10.10.110.2 via 10.10.110.2
Apr 18 00:01:37.533: MoH route If Vlan240 ETHERNET 10.10.201.1 via ARP
BR1-RTR#sh ip mr
BR1-RTR#sh ip mro
Apr 18 00:01:42.845: MoH route If Loopback0 46 10.10.110.2 via 10.10.110.2
Apr 18 00:01:42.845: MoH route If Vlan240 ETHERNET 10.10.201.1 via ARP
BR1-RTR#sh ip mrou
BR1-RTR#sh ip mroute
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report,
Z - Multicast Tunnel, z - MDT-data group sender,
Y - Joined MDT-data group, y - Sending to MDT-data group,
V - RD & Vector, v - Vector
Outgoing interface flags: H - Hardware switched, A - Assert winner
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode
(*, 239.1.1.1), 00:03:20/00:02:25, RP 0.0.0.0, flags: DCL
Incoming interface: Null, RPF nbr 0.0.0.0
Outgoing interface list:
Vlan240, Forward/Dense, 00:00:35/00:00:00
(*, 224.0.1.40), 08:48:14/00:02:24, RP 0.0.0.0, flags: DCL
Incoming interface: Null, RPF nbr 0.0.0.0
Outgoing interface list:
Vlan240, Forward/Dense, 08:48:14/00:00:00
BR1-RTR#
Apr 18 00:01:48.081: MoH route If Loopback0 46 10.10.110.2 via 10.10.110.2
Apr 18 00:01:48.081: MoH route If Vlan240 ETHERNET 10.10.201.1 via ARP
BR1-RTR#
Apr 18 00:01:53.417: MoH route If Loopback0 46 10.10.110.2 via 10.10.110.2
Apr 18 00:01:53.417: MoH route If Vlan240 ETHERNET 10.10.201.1 via ARP
BR1-RTR#
Apr 18 00:01:58.729: MoH route If Loopback0 46 10.10.110.2 via 10.10.110.2
Apr 18 00:01:58.729: MoH route If Vlan240 ETHERNET 10.10.201.1 via ARP
Apr 18 00:01:59.429: ifs_read flash:music-on-hold.au end of file at
492254 read 4267 = 496521
Apr 18 00:01:59.433: moh tail fill from 24 at 0x4A7BFC27 length 3733
BR1-RTR#
BR1-RTR#
BR1-RTR#
BR1-RTR#sh ccm-manager music-on-hold
Current active multicast sessions : 1
Multicast RTP port Packets Call Codec Incoming
Address number in/out id Interface
===================================================================
239.1.1.1 16384 2833/2833 69 g711ulaw Lo0
BR1-RTR#
On 17/04/2010 23:01, CCIETalk.com wrote:
So working through IPX Labs I ran into this. I can hear the "Piano"
music on my BR1 phones when I put them on hold but what will be
another way of testing this?
--
www.ccietalk.com <http://www.ccietalk.com>
_______________________________________________
For more information regarding industry leading CCIE Lab training, please visit
www.ipexpert.com
--
Thanks,
Ashar Siddiqui
_______________________________________________
For more information regarding industry leading CCIE Lab training, please visit
www.ipexpert.com