Thanks Constance ...
This helps alot!
""Constance Cate"" <[EMAIL PROTECTED]> wrote in message
8t6pui$uvu$[EMAIL PROTECTED]">news:8t6pui$uvu$[EMAIL PROTECTED]...
> Use dialer profiles on the Corp BRI interface (hub site) to define each of
> the 4 spoke sites and use floating static routes (or possibly dialer
watch)
> to activate the dialer profiles upon link failure.
> Basically you will define 4 logical dialer interfaces (kinda like sub
> interfaces) and each of these will use the physical BRI interface when it
is
> needed. The far end IP address and the dial string will be part of these
> logical interfaces which will allow multiple dialed destinations.
> The floating static routes (configured with a higher administrative
distance
> than the RIP routes) will become active when one of the RIP routes falls
out
> of the routing table due to a link failure. Traffic which was once
destined
> for a FR interface will now be directed to one of the logical dialer
> interfaces.
> If you have configured the hub site to connect to the spoke sites with
> separate physical interfaces (which I doubt) you could use a dialer watch
> configuration in the place of floating static routes. You may be able to
use
> dialer watch with sub-interfaces, I'm not sure. The floating static routes
> are a sure thing.
>
> Check out these links,
>
http://www.cisco.com/univercd/cc/td/doc/product/software/ios120/12cgcr/dial_
> c/dcdbakdp.htm
> http://www.cisco.com/warp/public/793/access_dial/ddr_dialer_profile.html
> HTH,
> Connie
>
> "FRS" <[EMAIL PROTECTED]> wrote in message 8t6nf8$l8u$[EMAIL PROTECTED]">news:8t6nf8$l8u$[EMAIL PROTECTED]...
> > Hi,
> >
> > I have 4 sites reporting back to Corp over FR ....
> > I need to implement ISDN backup to all sites ....
> > How do I get the single Corp BRI interface to accept the different
remote
> > BRI ip addresses and route accordingly ... I am running RIP ....
> >
> > righ now, only one remote sites is configured as:
> >
> > int bri0/0
> > ip x.x.3.2 255.255.255.0
> > no ip directed broadcast
> > encap ppp
> > dialer string 123456789
> > dialer string 987654321
> > dialer-group 1
> > isdn switch-type basic-5ess
> > isdn spid1 12345678901
> > isdn spid2 98765432101
> > ppp auth chap
> > ppp multilink
> >
> > corp config:
> >
> > int bri5/0
> > ip x.x.3.1 255.255.255.0
> > no logging event-subif-link-status
> > isdn spid1 998887776554
> > isdn spid2 887766554321
> > dialer-group 1
> > no fair-queue
> > ppp auth chap
> > ppp multilink
> >
> > the ip addresses of the other remote site's bri are x.x.4.2/24 ,
> > x.x.6.2/24, etc.
> >
> > my question is :
> >
> > how do i get the configure the corp bri interface to recognise x.x.4.2,
> > x.x.5.2, x.x.6.2 etc ... as it is now only configured for x.x.3.2 ....
> >
> > or does this not matter ....
> >
> > please help!
> >
> > thanks
> >
> >
> >
> >
> > _________________________________
> > FAQ, list archives, and subscription info:
> http://www.groupstudy.com/list/cisco.html
> > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
> >
>
>
> _________________________________
> FAQ, list archives, and subscription info:
http://www.groupstudy.com/list/cisco.html
> Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
>
_________________________________
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
