Take it this way,
With dialer profiles, the logical and physical configuration are dynamically
bound to each other on a per-call basis, which allows physical interfaces to
dynamically take on different characteristics based on incoming or outgoing
call requirements.
Lets go back to our practical situation.
on the HUB side (Corp router) you need to receive calls from more that one
spoke, then you need to apply profiles.
On the sopke side (remote) you will call just one place which is the Corp,
so there is no need for profiles here.
Hope this would help
Thanks a lot
ME
On Wed, 25 Oct 2000 09:51:11 -0400, Naasief Edross wrote:
> Thanks John!!!
> Do I do dialer profiles on the Corp router and dialer profiles on the
remote
> routers, or only the corp router?
> ----- Original Message -----
> From: "John lay" <[EMAIL PROTECTED]>
> Newsgroups: groupstudy.cisco
> Sent: Wednesday, October 25, 2000 9:55 AM
> Subject: Re: HELP! ISDN DDR
>
>
> >
> > You need to apply dialer profiles.
> > Dialer profiles allow you to configure B channels of an ISDN interface
> with
> > different IP subnets or Internetwork Packet exchange networks.
> >
> > ME
> >
> >
> >
> > On Wed, 25 Oct 2000 09:22:14 -0400, FRS wrote:
> >
> > > Hi,
> > >
> > > I have 4 sites reporting back to Corp over FR ....
> > > I need to implement ISDN backup to all sites ....
> > > How do I get the single Corp BRI interface to accept the different
> remote
> > > BRI ip addresses and route accordingly ... I am running RIP ....
> > >
> > > righ now, only one remote sites is configured as:
> > >
> > > int bri0/0
> > > ip x.x.3.2 255.255.255.0
> > > no ip directed broadcast
> > > encap ppp
> > > dialer string 123456789
> > > dialer string 987654321
> > > dialer-group 1
> > > isdn switch-type basic-5ess
> > > isdn spid1 12345678901
> > > isdn spid2 98765432101
> > > ppp auth chap
> > > ppp multilink
> > >
> > > corp config:
> > >
> > > int bri5/0
> > > ip x.x.3.1 255.255.255.0
> > > no logging event-subif-link-status
> > > isdn spid1 998887776554
> > > isdn spid2 887766554321
> > > dialer-group 1
> > > no fair-queue
> > > ppp auth chap
> > > ppp multilink
> > >
> > > the ip addresses of the other remote site's bri are x.x.4.2/24 ,
> > > x.x.6.2/24, etc.
> > >
> > > my question is :
> > >
> > > how do i get the configure the corp bri interface to recognise
x.x.4.2,
> > > x.x.5.2, x.x.6.2 etc ... as it is now only configured for x.x.3.2
....
> > >
> > > or does this not matter ....
> > >
> > > please help!
> > >
> > > thanks
> > >
> > >
> > >
> > >
> > > _________________________________
> > > FAQ, list archives, and subscription info:
> > http://www.groupstudy.com/list/cisco.html
> > > Report misconduct and Nondisclosure violations to
[EMAIL PROTECTED]
> >
> >
> >
> >
> >
> > _______________________________________________________
> > Say Bye to Slow Internet!
> > http://www.home.com/xinbox/signup.html
> >
> > _________________________________
> > FAQ, list archives, and subscription info:
> http://www.groupstudy.com/list/cisco.html
> > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
> >
_______________________________________________________
Say Bye to Slow Internet!
http://www.home.com/xinbox/signup.html
_________________________________
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
