We've always put the RSM in Slot 4...
"Mark Krysinski" <[EMAIL PROTECTED]> wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> Are you sure you can plug the RSM into slot #2. I remember someone
telling
> me to have it in slot 12. Please let me know if this is the case, our
5500
> uses slot 2 for a back up sup III module and slot 12 for the RSM with Vip
> module.
>
> Hope this helps.
>
> Mark
>
> -----Original Message-----
> From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of
> viathin
> Sent: Wednesday, December 20, 2000 6:59 PM
> To: [EMAIL PROTECTED]
> Subject: Re: problems configuring a 5500 chasis please help
>
>
> I tried plugging in an active switch into vlan 100 and it still was
saying
> that the vlan was not active or at least it appeared that way and i
couldn't
> ping it.
>
> ""Brian Gleason"" <[EMAIL PROTECTED]> wrote in message
> 91qoiu$1kf$[EMAIL PROTECTED]">news:91qoiu$1kf$[EMAIL PROTECTED]...
> >
> > Try plugging in a client machine into each of your vlans. I had this
> > problem with a 6509 and once the client link state came up, the
interface
> > came up.
> >
> >
> > ""viathin"" <[EMAIL PROTECTED]> wrote in message
> > 91plqc$2ti$[EMAIL PROTECTED]">news:91plqc$2ti$[EMAIL PROTECTED]...
> > > I'm having trouble configuring one router was wondering if you could
> help
> > >
> > > We are configuring a 5500 Chassis with:
> > > > >
> > > > > 1) WS X5530 Supervisor Engine (Slot 1)
> > > > > 2) WS X5302 Route Switch Module (Slot 2)
> > > > > 3) WS 5224 Switch ports (24 copper ports)
> > > > >
> > > > > A)
> > > > > We have defined:
> > > > > VLAN 100 on 3/1-4
> > > > > VLAN 200 on 3/5-8
> > > > > VLAN 300 on 3/9-12
> > > > > VLAN 500 on 3/21-24
> > > > > B)
> > > > > We have created the interfaces on the RSM:
> > > > > Config Terminal:
> > > > > 1) Interface vlan 100
> > > > > ip address 192.170.1.1 255.255.255.0
> > > > > 2) Interface vlan 200
> > > > > ip address 192.170.2.1 255.255.255.0
> > > > > 3) Interface vlan 300
> > > > > ip address 192.170.3.1 255.255.255.0
> > > > > 5) Interface vlan 500
> > > > > ip address 192.170.5.1 255.255.255.0
> > > > >
> > > > > Performed a no shutdown command on all interfaces.
> > > > >
> > > > > C)
> > > > > We implemented "eigrp 1" as the routing protocol using:
> > > > > Interface vlan 100
> > > > > router eigrp 1
> > > > > network 192.170.1.0
> > > > > network 192.170.2.0
> > > > > network 192.170.3.0
> > > > > network 192.170.5.0
> > > > > The above was repeated for all vlans (100,200,300,500)
> > > > > D)
> > > > > 1) Can not ping any vlan interfaces.
> > > > > 2) Performed a "Show Interface" and it shows all interfaces are
> down.
> > > > >
> > > > >
> > > > > Thanks for looking into this and we appreciate any insight on this
> > > > > problem.
> > > > >
> > > > Craig.
> > >
> > >
> > >
> > > _________________________________
> > > FAQ, list archives, and subscription info:
> > http://www.groupstudy.com/list/cisco.html
> > > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
> > >
> >
> >
> > _________________________________
> > FAQ, list archives, and subscription info:
> http://www.groupstudy.com/list/cisco.html
> > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
> >
>
>
> _________________________________
> FAQ, list archives, and subscription info:
> http://www.groupstudy.com/list/cisco.html
> Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
>
> _________________________________
> FAQ, list archives, and subscription info:
http://www.groupstudy.com/list/cisco.html
> Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
>
_________________________________
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]